“Dynasty” TV/Media Stand MS986400TX- Antique White Finishing MS986500TX- Espresso Finishing Assembly Instructions For assistance with assembly contact: Southern Enterprises Inc. Customer Service 1-800-633-5096 service@seidal.com www.seidal.
“Dynasty” TV/Media Stand Parts List Please review all parts and hardware before disposing of any packaging. Call Customer Service if missing hardware. Using hardware that is too long will cause damage. Before beginning assembly, separate each type of hardware. Carefully study the hardware diagrams below.
“Dynasty” TV/Media Stand Parts List Please review all parts and hardware before disposing of any packaging. Call Customer Service if missing hardware. Using hardware that is too long will cause damage. Before beginning assembly, separate each type of hardware. Carefully study the hardware diagrams below. You may receive extra hardware with your unit (1) Quantity (2) of 16 8mm x 30 mm Wood Dowel (4) 1/4” x 1” Bolt Quantity (5) of 1 3.
“Dynasty” TV/Media Stand Assembly Instructions Assembly Instructions: Wood may scratch easily. Be careful when assembling. Do not scratch. Step 1. Unpack and lay parts on clean, padded surface like carpet or blanket. Check that you have all parts indicated on the front page. Step 2. Put the Top Panel (A) on the soft working surface. Step 3. Attach the Single Magnet(3) and Double Magnet(4) to the Top Panel(A) with Screw For Magnet(5), then fasten them.
“Dynasty” TV/Media Stand Assembly Instructions Step 1. Insert the Wood Dowels(1) into predrilled holes in Bottom Panel(F) and Middle Panels(B,C) as pictured. Step 2. Attach the Bottom Panel(F) to the Right Side Panel(E) and Middle Panels(B,C). Quantity of 6 (1) 8mm x 30 mm Wood Dowel Figure 3 Step 1. Insert the Wood Dowels(1) into predrilled holes in Bottom Panel(F). Step 2. Attach Left Side Panels(D) to the Top Panel(A) and Bottom Panel (F) with Bolt(2) and flat Washer(6), then fasten them.
“Dynasty” TV/Media Stand Assembly Instructions P F Step 1. Put the flat Washer(6) into Allen Bolt (7), attach the Legs(H) into corner block with Allen Bolt (7) by Allen Wrench(8), Then fasten them. Step2. Attach the Middle leg (P) to bottom panel (F) as shown Quantity of 8 (6) Washer Quantity of 8 (7) 1/4” x 1-1/2” Allen Bolt Quantity of 1 (8) Allen Wrench Figure 6 Step 1. Attach the Back Panel(I) as pictured with Screw For Back(9), then fasten them. Quantity of 16 (9) 3.
“Dynasty” TV/Media Stand Assembly Instructions Step 1. Attach Left Middle Door (L) to Left Middle Panel(B) with Screw (10) for Door, then fasten them. Step 2. Attach Right Middle Door (M) to Right Middle Panel(C) with Screw (10) for Door, then fasten them. Step 3. Attach Handle (11) to Doors(L,M) with Bolt For Handle(12). Quantity of 12 (10) 3.5mm x 12mm Screw For Door Quantity of 1 (11) Metal Handle Quantity of 4 (12) 5/32” x 12mm Bolt For Handle Figure 9 Step 1.
Parts Replacement Form Customer Information Name Address City/State/Zip Code Phone Number Please indicate where you purchased this item: Store/Website/Catalog Please indicate color/size/style number: Style No Parts Letter Parts Description Quantity Needed Please immediately examine this product carefully. Any request for missing parts or damage replacement must be received within 90 days of your receipt of the product. Replacement, if available, will be honored within this time frame.
CAUTION The top shelf is intended for a flat screen television with a maximum overall width of 46” and supports up to 175 lb. The top shelf is NOT INTENDED for tube televisions. Each shelf should not be loaded with more than 20 lb. DO NOT EXCEED RECOMMENDED LOAD. Use with products heavier than the maximum sizes and weights indicated may result in instability causing possible injury. This unit contains a permanent warning sticker located on under side of top shelf or inside drawer.