User's Manual

80*120mm.
---风琴折.
W37A 709-0000-0000
0000000
◆Packing list:
◆
QUICK INSTALLATION GUIDE：
3 4
1
2
1000 M WAN/L AN
Pow er
WPS ON/ OFF
Connect the Ethernet
interface to any
Ethernet port
Internet access
on the wall
DSL/PON/Cable Gateway
Reset
Reset
Product name：WiFi 6 AP
Product model：WA6 -B F0 WW
IP：192.168.0.1
SSID(2.4G)：WiFi6AP- XXXX
SSID(5G)： WiFi6AP-XXXX-5G
Password：XXXXXXXX
MAC: XX:XX:XX:XX:XX:XX
S/N: XXXXXXXXXXXX
Made in China
Power
O N/OFF
R esetGE
10G_LAN
10G_PON
or
1 2
• Power Adpater
• User manual
• Ethernet cable
• Wi-Fi 6
！Please contact your service provider if any item is missing
80g paper(80克书写纸）
Step One:
Power on the Router and Connect To the Internet
Step Two: Plug and Play
（1）Connect the Router to a power source
（2）Connect the Ethernet interface from a DSL/PON/Cable Gateway to
any Ethernet port of the Wi-Fi 6 Router through a network cable.
（1）Wi-Fi6 Router is ready when its LED light shows steady Green.
（2）Look for Wi-Fi network name (SSID) and key (password) on the
bottom of the Router. Connect a wireless device (for example Wi-Fi
enabled computer or mobile phone) to the Wi-Fi 6 router.
Alternatively, connect a wired device by inserting a network cable to
any of the Wi-Fi 6 router’s Ethernet ports.
If changing the Wi-Fi SSID and/or password,
please refer to the following steps:
※Wi-Fi Settings
（1）Set up either a wireless or wired connection as indicated in
“Step One” and “Step Two”. Launch a web browser and enter
http://192.168.0.1 in the address bar.
（2）You need to set the login password when you enter the page for the
first time. And then click “Next”.
（3）Internet Configuration Settings
Connect a cable from your PON/DSL/Cable gateway to the Wi-Fi 6
router, and choose ”DHCP”, after click “Next”, the Wi-Fi router is ready.
！Note: if you forgot the Broadband account and Password, you can
contact to broadband network provider (AIS) to get these
information.
！Note: if click “Skip”, default choosing “DHCP” .
（4）Changing the Wi-Fi Network Name and Password
The router default selects “The password is the same as the login password”.
It means new Wi-Fi password is the same as login password, click “Next”.
If not select “The password is the same as the login password”, you can
enter a different Wi-Fi password in the password field, click “Next”.
！If click “Skip”, Wi-Fi information still as shown on the label.
（5）Click “Complete”, finishing the settings.
When “Setup Succeed”, click “Confirm”, it will jump to the login page.
LED
Indicates Behavior
Connecon to the power supply
Red inially , then blinking green
Power on, no network Blinking Red
Power on, network being connected… Blinking Green
The router is ready Steady Green
WPS (Press WPS buon or click WPS on the web
page). WPS or Mesh pairing acon is in progress.
Blinking Blue
WPS or Mesh paring acon is successful
Steady Blue for 1min, then blue
light goes off
WPS ac
on failed Blue light off
1. Why can’t I access the web based configuration?
FREQUENTLY ASKED QUESTIONS
Answer：(1) Check the connection between the Network cable and the
Wired device. Check correct Wi-Fi connection in the
wireless device.
(2) Check your IP Address. Your computer must have an IP
Address in the same range of the device you are attempting
to configure. If not, the resolve solution is：Setting the
computer’s TCP/IP to “Obtain an IP address automatically”
and ”Obtain DNS server address automatically” .
(3) Check URL in browser：Launch a web browser and enter
the router’s IP Address (192.168.0.1), enter the login
password and then the home page displays.
2. If forgot the login password, what to do?
Answer：You can use a needle to press the Reset button on the bottom
of the router and keep pressing more than 10s before you
release the button. The router will restart for 2~3mins and finish
restore factory setting. Then you can enter” http://192.168.0.1”
to reset the login password.
Answer:
3. Wi-Fi enabled device can connect the router, but there is no network.
What to do?
(1) Check the Ethernet cable connection to your
DSL/PON/Cable gateway.
(2) If “PPPoE” is chosen, you need to check if you enter the
right broadband account and password.
(3) Make sure your broadband account is active, contact your
service provider.
(4) If all above are ok, please restart the router. Power off
after 10s, then power on the router.
If PPPoE is required alternatively, connect a cable from your
PON/DSL/Cable gateway to the Wi-Fi 6 router and Choose “PPPoE”,
and then enter the Broadband account and Password, and click “Next”.
3 4 5 6
Open the Wi-Fi connection manager on your Wi-Fi-enabled computer or
mobile device, find the router’s new Wi-Fi network name (ssid), and use
the router’s new password to connect.
AZORES
AX1500
Wi-Fi 6 MESH AP
AZORES