355 Old Road Clacton On Sea Essex CO15 3RH Tel: +44 (0)1255 422807 Fax: +44 (0)1255 436342 www.bowens.co.uk ʻBowensʼ ® and ʻthe power behind the pictureʼ ® are registered trademarks of Bowens International Ltd.
Introduction Table of Contents Dear Valued Customer, Description Page Introduction and Safety Notes 3 Thank you for choosing the Bowens Esprit Gemini Digital professional flash system. Control Panel Guide 4 Connecting & Using the Esprit Gemini 5 Mounting 5 Fitting the Modelling Lamp 6 Accurate, ergonomic, powerful and simple to use, the Esprit Gemini Digital was designed by working closely with photographers to develop a flash that meets the standards demanded in professional studios today.
Connecting & Using the Esprit Gemini Digital Control Panel Guide !!! WARNING HIGH VOLTAGE !!! Rear Control Panel Mains / Battery Power Select Carry Handle NEVER CONNECT THE ESPRIT GEMINI DIGITAL TO BOTH A MAINS SUPPLY AND A BATTERY SUPPLY AT THE SAME TIME. THIS APPLIANCE MUST BE EARTHED WHEN USED WITH MAINS. DISCONNECT THE MAINS LEAD WHEN CHANGING MODELLING LAMPS & FLASH TUBES.
Synchronisation cont. Fitting the Modelling Lamp Switch off and disconnect from the supply. Screw modelling lamp into ES lampholder in the centre of the reflector. Allow lamp to cool before removing. Note: It is recommended that a Photoflood or Halostar bulb with a maximum wattage of 275W is used. Bowens will not accept liability on the use of any lamp with a greater wattage than 275W. Fitting / Removing Reflectors A wide range of reflectors are available for the Esprit range.
Normal Functions Functions Overview During normal use simply rotate the dial to adjust the power to the required level. The unit ready indication is by means of a ʻsteadyʼ display and a sounder beep (if on) as well as the modelling lamp indication function when the unit reaches ready (if switched on). While changing the power level the display flashes at different rates to indicate whether the unit is charging or if there is excess power that needs dumping.
Functions Menu System Advanced Functions Menu Top Level Function Display Description Press ‘Menu’ *LP Audio (Key Clicks & Warnings) AUD Off (OFF) - All audible beeps/clicks are turned off during normal operation i.e. while scrolling through the functions menu. On (ON) - All audible beeps/clicks are enabled while unit is powered on.
Photocell Modelling Lamp Ready Indicator The modelling lamp can be used as an indicator of when the unit has flashed, and also when it has charged and is ready to fire again. All modelling lamp options are only available when the unit is operating from mains power. The available options for the modelling lamp ready indicator are: Off (OFF) - No lamp ready indication; the modelling lamp remains on or off during operation depending on ʻLampʼ settings.
Battery Power Additional Information Notes: Setting ʻFldʼ to ʻonʼ will automatically flash the unit to dump any excess energy if the user reduces the power output setting and makes no further adjustments within 2 seconds. The modelling lamp has a micro controlled soft ʻonʼ and ʻoffʼ to prolong the life of the bulb. The ʻkey clickʼ & ʻwarning sounderʼ can be turned ʻonʼ or ʻoffʼ independently of the ʻreadyʼ sounder. This option is available within the Advanced Functions.
Accessories Pulsar Clip-On Platform With The Pulsar clip-on platform is a handy way of attaching your radio trigger units to almost anything around your studio or even whilst out on location. Simply attach your loose Pulsar unit to the platform and clip onto whatever you need to. A great way of saving valuable time and effort in the studio. 65° Maxilite Reflector This is a good general-purpose direct reflector with an even coverage and a high light output.
Specifications Specifications Unit GMD250 GMD500 BW3700 BW3705 BW3710 BW3715 Stored Energy (max) 250Ws 500Ws Sync Voltage 5V 5V Flash Colour Temperature 5600K ±300K 5600K ±300K Circuit Protection 230V - 5A (F) (117V - 10A (T)) 230V - 5A (F) (117V - 10A (T)) Supply Voltage Range 230V (117V) 190-250V AC 50Hz (95-130V AC 60Hz) 190-250V AC 50Hz (95-130V AC 60 Hz) 56.1 79.8 0.81 (1.1) secs 1.54 (1.
