ll09636 Issue 2 800 Series 800D 801D 802D 803D HTM1D HTM2D T +44 (0) 1903 221800 F +44 (0) 1903 221801 info@bwgroup.com www.bwspeakers.com MOISTEN B&W Group (UK Sales) T +44 1903 221 500 E uksales@bwgroup.com B&W Group North America T +1 978 664 2870 E marketing@bwgroupusa.com B&W Group Asia Ltd T +852 2 869 9916 E showroom@bwgroup.hk Copyright © B&W Group Ltd. E & OE Rohacell is a registered trademark of Rohm GmbH Kevlar is a registered trademark of DuPont. Printed in England.
Owner details Contents Figure 1 Figure 7 800D 801D 802D 803D 803S 804S 805S SCMS HTM1D HTM2D HTM3S HTM4S Figure 8 Figure 9 DS8S Title, first name, surname English Limited Warranty...........1 Owner’s Manual............1 Français Garantie limitée.............7 Manuel d’utilisation .......7 Deutsch Garantie .....................14 Bedienungsanleitung...15 Español Garantía limitada.........22 Manual de instrucciones ..............22 Português Garantia limitada.........30 Manual do utilizador....
Figure 26 Figure 19 Figure 27 Figure 28 Figure 36 SPEAKERS OUT Amplifier 12V TRIG OUT Processor Figure 20 Figure 29 Figure 30 Figure 37 FIgure 22 Figure 23 Figure 31 Figure 33 Figure 32 Figure 38 Figure 24 Figure 25a Figure 25b Figure 34 Figure 39 Figure 35 Glue Area Figure 21
English How to claim repairs under warranty Should service be required, please follow the following procedure: Limited Warranty Dear customer, Welcome to B&W. This product has been designed and manufactured to the highest quality standards. However, if something does go wrong with this product, B&W Loudspeakers and its national distributors warrant free of charge labour (exclusion may apply) and replacement parts in any country served by an official B&W distributor.
Contact your dealer if there are any missing items. 2 POSITIONING Stray magnetic fields If you are using speakers in a home theatre set-up and you are using a CRT screen (a traditional tube television or back projector), make sure the picture is not going to be distorted by stray magnetic fields from the drive unit motor systems.
Use the bottom switch on the front baffle when selecting between monopole and dipole modes. In the • position, the speaker defaults to monopole. (figure 8) placed directly behind the centre of the listening area. (figure 14) f Go to section 2.8 2.7 However, if a 12V signal is applied to the trigger input, internal relays switch to dipole mode. In the •• position, the speaker is always in dipole mode, whatever the trigger signal.
Screw in the feet with locking ring attached, with either the spikes or rubber tips outermost, according to the type of floor surface. Leave the tips of the feet protruding beyond the inner packing pieces for clearance when the speaker is upright. After rolling the cabinet onto its feet and lifting off the carton, remove the inner packing and adjust the feet as described in section 3.3 f Continue to section 3.3. 3.
4 CONNECTIONS All connections should be made with the equipment switched off. The terminals accept a variety of cable terminations to suit most applications – 4mm banana plugs, 6mm and 8mm (1/4 in and 5/16 in) spades, or bare wires up to 6mm (1/4 in) diameter. Important safety notice In certain countries, notably those in Europe, the use of 4mm banana plugs is considered a potential safety hazard, because they may be inserted into the holes of unshuttered mains supply sockets.
5 FINE TUNING shaped surfaces such as bookshelves and large pieces of furniture. Before fine tuning, double check that all the connections in the installation are correct and secure. DS8S only In monopole mode, the high-frequency output level may be adjusted using the top toggle switch on the front baffle. (figure 39) Floor- and stand-mount speakers only Moving the speakers further from the walls will reduce the general level of bass.
gripping round the edges and gently pulling them away from the cabinet. Spray onto the cleaning cloth, not directly onto the cabinet. The grille fabric may be cleaned with a normal clothes brush whilst the grille is detached from the cabinet. When replacing grilles, ensure that the pegs are correctly aligned with the receptacles in the cabinet before pushing into place.