Copyright This publication, including all photographs, illustrations and software, is protected under international copyright laws, with all rights reserved. Neither this manual, nor any of the material contained herein, may be reproduced without written consent of the author. © Copyright 2009 Disclaimer The information in this document is subject to change without notice.
D DLLPP PPrroojjeeccttoorr— —U Usseerr’’ss M Maannuuaall Important Safety Information Congratulations on purchasing the BOXLIGHT DLP projector! Important: It is strongly recommended that you read this section carefully before using the projector. These safety and usage instructions will ensure that you enjoy many years of safe use of the projector. Keep this manual for future reference. Symbols Used Warning symbols are used on the unit and in this manual to alert you of hazardous situations.
PPrreeffaaccee Power Safety ¾ Only use the supplied power cord. ¾ Do not place anything on the power cord. Place the power cord where it will not be in the way of foot traffic. ¾ Remove the batteries from the remote control when storing or not in use for a prolonged period. Replacing the Lamp Replacing the lamp can be hazardous if done incorrectly. See Replacing the Lamps on page 83 for clear and safe instructions for this procedure. Before replacing the lamp: ¾ Unplug the power cord.
D DLLPP PPrroojjeeccttoorr— —U Usseerr’’ss M Maannuuaall Main Features x Lightweight unit, easy to pack away and transport. x Compatible with all major video standards including NTSC, PAL, and SECAM. x A high brightness rating allows for presentations in daylight or in lit rooms. x Supports resolutions up to UXGA at 16.7 million colors to deliver crisp, clear images. x Flexible setup allows for front, rear projections.
PPrreeffaaccee Table of Contents INTRODUCTION................................................................................................................................................................. 1 PACKING CHECKLIST ........................................................................................................................................................... 1 VIEWS OF PROJECTOR PARTS ......................................................................................................
D DLLPP PPrroojjeeccttoorr— —U Usseerr’’ss M Maannuuaall USING THE PHYSICAL LOCK .............................................................................................................................................. 46 Using the Kensington Lock ........................................................................................................................................... 46 USING ON-SCREEN DISPLAY.............................................................................................
PPrreeffaaccee Control Command Diagram ......................................................................................................................................... 99 Control Sequence .......................................................................................................................................................... 99 Operation Commands ..........................................................................................................................................
D DLLPP PPrroojjeeccttoorr— —U Usseerr’’ss M Maannuuaall Bottom view ITEM LABEL DESCRIPTION SEE PAGE: 32 1. Height adjusters Adjust projection height 2. Ceiling support holes Contact your dealer for information on mounting the projector on a ceiling Note: When installing, ensure that you use only UL Listed ceiling mounts. Caution: With ceiling installation, use approved mounting hardware & M4 screws; maximum depth of screw: 12 mm; distance from ceiling/ wall: 20 cm (0.
D DLLPP PPrroojjeeccttoorr –– U Usseerr’’ss M Maannuuaall Top Features Lens Controls ITEM LABEL 1. ZOOM 2. UP CURSOR 3. RIGHT CURSOR 4. DOWN CURSOR 5. LEFT CURSOR 6.
D DLLPP PPrroojjeeccttoorr— —U Usseerr’’ss M Maannuuaall OSD Controls and Status LEDs ITEM LABEL DESCRIPTION SEE PAGE: 1. MENU Open / Close the OSD 47 2. UP/ DOWN/ LEFT/ RIGHT BUTTONS Navigate and change settings in the OSD 47 3. RIGHT CURSOR/ VOLUME INCREASE Increase volume 34 4. CANCEL Exit the On-Screen Display (OSD) 47 5. SOURCE Detects the input device 27 6. POWER Turn the projector on or off (main power switch must be turned on first).
D DLLPP PPrroojjeeccttoorr –– U Usseerr’’ss M Maannuuaall ITEM LABEL DESCRIPTION SEE PAGE: Green 10. POWER (LED) Orange See Indicator Messages 87 Flashing 11. AUTO 12. 13.
D DLLPP PPrroojjeeccttoorr— —U Usseerr’’ss M Maannuuaall Terminal Panel Features ITEM LABEL DESCRIPTION SEE PAGE: 1. COMPUTER 3 IN Connect the DVI-D cable (not supplied) from a computer 2. AUDIO IN (COMPUTER 3) Connect the audio cable (not supplied) from the input device 3. AUDIO OUT Audio loop-thru 4. MONITOR OUT Connect to a monitor 5. AUDIO IN (COMPUTER 2) Connect the audio cable (not supplied) from the input device 6.
D DLLPP PPrroojjeeccttoorr –– U Usseerr’’ss M Maannuuaall ITEM LABEL DESCRIPTION SEE PAGE: 10. POWER SWITCH Turn on/off the projector 35 11. AC IN Connect the supplied power cable 25 12. AUDIO IN [L (MONO)/R] (VIDEO) Connect RCA audio cables (not supplied) from the input device right and left channels. This audio jack is shared with S-Video input. 24 13. VIDEO IN Connect a composite video cable (not supplied) from a video device to the yellow RCA jack 23 14.
D DLLPP PPrroojjeeccttoorr— —U Usseerr’’ss M Maannuuaall Remote Control Parts Important: 1. Avoid using the projector with bright fluorescent lighting turned on. Certain high-frequency fluorescent lights can disrupt remote control operation. 2. Be sure nothing obstructs the path between the remote control and the projector. If the path between the remote control and the projector is obstructed, you can bounce the signal off certain reflective surfaces such as projector screens. 3.
D DLLPP PPrroojjeeccttoorr –– U Usseerr’’ss M Maannuuaall ITEM LABEL 7. Up cursor 8. Right cursor DESCRIPTION SEE PAGE: Navigates and changes settings in the OSD 47 Navigates and changes settings in the OSD 47 34 9. Down cursor 10. Volume +/- Adjusts volume 11. Mute Mutes the built-in speaker 12. Zoom+ Zoom in 13. Zoom- Zoom out 14. Freeze Freeze/unfreezes the on-screen picture 15. Blank Makes the screen blank 16. Source Detects the input device 17.
D DLLPP PPrroojjeeccttoorr— —U Usseerr’’ss M Maannuuaall Remote Control Operating Range The remote control uses infrared transmission to control the projector. It is not necessary to point the remote directly at the projector. Provided you are not holding the remote perpendicular to the sides or the rear of the projector, the remote will function well within a radius of about 7 meters (23 feet) and 15 degrees above or below the projector level.
SETUP AND OPERATION Inserting the Remote Control Batteries 1. 2. 3. Remove the battery compartment cover by sliding the cover in the direction of the arrow. Insert the supplied batteries taking note of the polarity (+/-) as shown here. Replace the cover. Caution: 1. Only use AAA batteries. (Alkaline is better). 2. Dispose of used batteries according to local ordinance regulations. 3. Remove the battery when not using the projector for prolonged periods.
D DLLPP PPrroojjeeccttoorr –– U Usseerr’’ss M Maannuuaall Screen Size Diagonal [inches] [m] Width [inches] 912 Lens 2.22 - 4.43 Height [m] [inches] [m] [inches] 913 Lens 4.43 - 8.3 [m] Distance [inches] [m] 40 1.02 32 0.81 24 0.61 69.4 - 142.3 1.76 - 3.61 139.2 - 266.9 3.54 - 6.78 50 1.27 40 1.02 30 0.76 87.8 - 178.9 2.23 - 4.54 175.3 - 335.0 4.45 - 8.51 60 1.52 48 1.22 36 0.91 106.2 - 215.5 2.70 - 5.47 211.5 - 403.1 5.37 - 10.24 67 1.70 54 1.36 40 1.02 119.
D DLLPP PPrroojjeeccttoorr— —U Usseerr’’ss M Maannuuaall Installing the Optional Color Wheel The projector comes with a four-segment color wheel installed. An additional six-segment color wheel is optional. To replace the color wheel (located under the lamp cover adjacent to lamp 1) refer to the following guide. Note: Wait until the lamp house and the color wheel cool off. 1. Remove the four screws (A) on the lamp cover. 2. Lift the lamp cover in the direction of the arrow (B). 3.
D DLLPP PPrroojjeeccttoorr –– U Usseerr’’ss M Maannuuaall 4. 5. Lift the color wheel in the direction shown.
D DLLPP PPrroojjeeccttoorr— —U Usseerr’’ss M Maannuuaall 6. Close the lamp cover and secure the retaining screws as shown. Storing Unused Color Wheel: Keep the unused color wheel in the zipper bag in which the 6-segment color wheel (not supplied) was packaged. This bag prevents dust from falling or collecting on the color wheel.
D DLLPP PPrroojjeeccttoorr –– U Usseerr’’ss M Maannuuaall Making Connections Connecting Your PC or Macintosh Computer Enabling the computer’s external display: Displaying an image on the notebook PC’s screen does not necessarily mean it outputs a signal to the projector. When using a PC compatible laptop, a combination of function keys will enable/disable the external display. Usually, the combination of the Fn-key along with one of the 12 function keys activates the external display.
D DLLPP PPrroojjeeccttoorr— —U Usseerr’’ss M Maannuuaall Note: Failure to follow the above steps may not activate the digital output of the graphics card resulting in no picture being displayed. Should this happen, restart your PC. Connecting an External Monitor Connect an external monitor to the projector through RGB out connections as shown below (see Terminal Panel Features on page 8).
D DLLPP PPrroojjeeccttoorr –– U Usseerr’’ss M Maannuuaall Connecting Your DVD Player with Component Output To connect a DVD Player to the projector, refer to the following guide. 1. Connect the DVD Player to the projector as shown below before turning on the Player or the projector. 2. Turn on the projector and select Component from the source menu before turning on the DVD Player (see Selecting an Input Source on page 27). 3. Turn on the DVD Player.
D DLLPP PPrroojjeeccttoorr— —U Usseerr’’ss M Maannuuaall Connecting Your VCR or Laser Disc Player To connect your VCR or Laser Disc Player, refer to the following diagram. Note: Refer to your VCR or laser disc player user’s manual for more information about your device’s requirements. Images may not be displayed correctly when using an S-Video or Video connection to fast-forward or fast-rewind scanning. The AUDIO IN RCA jack is shared between VIDEO IN and S-VIDEO IN.
PROJECTING AN IMAGE (BASIC OPERATION) Turning on the Projector Once the projector is correctly located and the power cable and other connections are in place, it is important that the projector is powered on correctly in order to avoid damage to components and unnecessary wear and tear. Refer to the following guide to power on the projector. 1. Connect the power cable (A). Press the main power switch to the on ( I ) position as shown (B).
D DLLPP PPrroojjeeccttoorr— —U Usseerr’’ss M Maannuuaall Note on Startup Screen (Menu Language Select screen) In the first instance of powering on the projector, the language menu is displayed to select the default language. Select the required default language using the Ÿ or ź buttons on the OSD menu panel or the remote . control unit and press Note: The language select screen only appears on the first instance of power on. All subsequent operations assume the selected default language.
D DLLPP PPrroojjeeccttoorr –– U Usseerr’’ss M Maannuuaall Selecting an Input Source The Input Source can be selected from the projector's control panel or from the remote control unit. Refer to the following guide to select the Input Source. 1. Press Menu on the OSD control panel or on the remote control unit to display the Main Menu. Scroll to the Input menu using Ÿorź and press . Note: Return to the projected image by pressing Cancel twice. 2. Select the required source using Ÿorź and press .
D Maannuuaall DLLPP PPrroojjeeccttoorr –– U Usseerr’’ss M 4. 5. The Screen window is displayed. Select the desired picture size using Ÿorź and press . When finished, press Cancel to return to the projected image. Lens Shift Adjustable Range The adjustable range for lens shift is tabulated below and subject to the conditions listed. Note: The drawings below apply to the standard lens only.
D DLLPP PPrroojjeeccttoorr –– U Usseerr’’ss M Maannuuaall 4. 5. 6. To alter the picture size, press Menu and select the Adjust menu using Ÿorź. Press to open the Adjust menu. Press ŻorŹ to select Image Options followed by Ÿorź to select Screen. Press . Select the desired picture size using Ÿorź and press . When finished, press Menu to return to the projected image.
D DLLPP PPrroojjeeccttoorr— —U Usseerr’’ss M Maannuuaall Adjusting the Projector Level 1. 2. To raise the level of the projector, twist the adjusters clockwise. To lower the level of the projector, lift the projector and twist the adjusters counter clockwise.
D DLLPP PPrroojjeeccttoorr –– U Usseerr’’ss M Maannuuaall Optimizing an RGB Image Automatically Adjusting the Image Using AUTO To optimize an RGB image automatically refer to the following guide. Press the Auto button on the remote control (see Remote Control Parts on page 10) or the AUTO button on the OSD control panel to optimize an RGB image automatically. This adjustment may be necessary when you connect your computer for the first time.
D DLLPP PPrroojjeeccttoorr— —U Usseerr’’ss M Maannuuaall Adjusting Volume Up and Down The volume can be adjusted from the OSD Control Panel or with the Remote Control unit. Refer to the following as a guide. 1. 2. Press the Volume +/- buttons on the remote control or the Ż Ź buttons on the OSD control panel. The volume level is displayed on screen. Use the Volume +/- buttons or the Ż Ź buttons on the OSD control panel to adjust the level.
D DLLPP PPrroojjeeccttoorr –– U Usseerr’’ss M Maannuuaall Turning off the Projector Once the projector is no longer required, it is important to shut it down correctly to avoid damage or unnecessary wear and tear to the projector. Note: y Do not unplug the power cable from the wall outlet or projector when the projector is powered on. Doing so can cause damage to the AC IN connector of the projector and (or) the prong plug of the power cable.
D DLLPP PPrroojjeeccttoorr— —U Usseerr’’ss M Maannuuaall About Direct Power Off The projector has a feature called "Direct Power Off". This feature allows the projector to be turned off (even when projecting an image) using a power strip equipped with a switch and a breaker. Note: Before using Direct Power Off, be sure to allow at least 20 minutes immediately after turning on the projector and starting to display an image. After Use Preparation: Make sure that the projector is turned off. 1.
CONVENIENT FEATURES Turning Off the Image and Sound The projected image and sound can be turned off for short periods of time with the remote control. This feature is useful for breaking up presentations or for other brief interruptions in projections. To turn off the picture and image, refer to the following guide. 1. Press the Blank button on the remote control once (see Remote Control Parts on page 10). 2. The image does not display. 3. To resume projection, press the Blank button once more.
D DLLPP PPrroojjeeccttoorr— —U Usseerr’’ss M Maannuuaall Adjusting the Focus/Zoom Manually The focus and zoom can be adjusted manually from the projector focus/zoom panel. Refer to the following guides to adjust the focus and zoom manually. Adjusting by Using the OSD Control Panel 1. 2. 3. Press the Focus or Zoom button on the projector panel to display the appropriate window. Adjust the Focus/Zoom using the increase and decrease buttons as required. Press Cancel to return to the projected image.
D DLLPP PPrroojjeeccttoorr –– U Usseerr’’ss M Maannuuaall Changing Lamp Mode The projector has two lamp modes available, Normal and Eco. The Normal mode is used for everyday standard projection, whereas the Eco mode is used for saving power and lamp life. To change the Lamp Mode, refer to the following guides. Changing Lamp Mode by Using the Projector's OSD Control Panel 1. 2. 3. Press Menu on the projector's OSD control panel to display the Main menu. Scroll to the Setting menu using Ÿorź and press .
D DLLPP PPrroojjeeccttoorr— —U Usseerr’’ss M Maannuuaall Getting Information The Information screen provides details on the life of consumable items within the projector as well as other information such as software version. To access the Information screen, refer to the following guide. 1. 2. 3. Press Menu on the projector's OSD control panel or remote control to display the Main Menu. Scroll to the Information menu using Ÿorź and press . The Usage time menu is displayed as the default view.
D DLLPP PPrroojjeeccttoorr –– U Usseerr’’ss M Maannuuaall Adjusting Position/Total Dots/Fine Sync The Position/Total dots/Fine sync and Keystone Correction can be adjusted manually from the projector's control panel or from the remote control unit. Refer to the following guides to adjust the Keystone Distortion manually. Adjusting Position/Total Dots/Fine Sync by using the OSD Control Panel 1. 2. 3. 4. Press the Menu button to display the Main menu.
D DLLPP PPrroojjeeccttoorr— —U Usseerr’’ss M Maannuuaall Correcting Keystone by Using the Remote Control Important: When adjusting the keystone, place the projector in the following position. y Horizontal: set to the lens center y Vertical: set to the maximum top 1. 2. 3. 4. Press the Keystone button to display the Keystone window. Adjust the Horizontal and Vertical sliding bars using the select ŸźŻŹ buttons. Adjust the slide bars until the screen trapezoid is a regular shape (see diagram).
D DLLPP PPrroojjeeccttoorr –– U Usseerr’’ss M Maannuuaall ADJUSTMENT Keystone HORIZONTAL Max. +/– 35° approx. VERTICAL Max. +/– 40° approx. The following are conditions under which the maximum angle is achieved: When the standard lens is used When the lens shift is set to H for center and V for 0.5 shift. When the lens shift is used and yet you do not get the above-mentioned condition (H for center and V for 0.5 shift), you cannot adjust the lens shift correctly.
D DLLPP PPrroojjeeccttoorr— —U Usseerr’’ss M Maannuuaall Preventing the Unauthorized Use of the Projector The projector has a built-in security feature to lock the OSD control panels and deny remote control operation. The security feature has no default keyword; in the first instance of enabling the security feature, the user must define a keyword. Locking the Projector To setup the security keyword, refer to the following guide. 1. 2. 3.
D DLLPP PPrroojjeeccttoorr –– U Usseerr’’ss M Maannuuaall 4. 5. The PIN code window is displayed. Enter a PIN code between 4 and 10 characters using ŸźŻŹ. The PIN code characters change to “*”. Press . Once a successful PIN code is entered, a confirmation screen is displayed. Enter the same password as the previous step and write it down for later reference. Press . A security activation message is displayed. Select Cancel or Menu to return to the Setting menu or select OK to enable security.
D DLLPP PPrroojjeeccttoorr— —U Usseerr’’ss M Maannuuaall Using the Physical Lock Using the Kensington Lock If you are concerned about security, attach the projector to a permanent object with the Kensington slot and a security cable.
USING ON-SCREEN DISPLAY Using the Menus The projector has an On-Screen Display (OSD) that lets you make image adjustments and change various settings. Navigating the OSD You can use the remote control or the buttons on the top of the projector to navigate and make changes to the OSD. The following illustration shows the corresponding buttons on the remote control and on the projector. 1. To open the OSD, press the Menu button on the OSD control panel or remote control. There are six initial menus.
D DLLPP PPrroojjeeccttoorr— —U Usseerr’’ss M Maannuuaall 2. 3. 4. Press the cursor Ż or Ź button to move through secondary menus. Press Ÿorź to select menu items and ŻorŹ to change values for settings. Press to confirm the new setting. Press Cancel or Menu to close the OSD or leave a submenu.
D DLLPP PPrroojjeeccttoorr –– U Usseerr’’ss M Maannuuaall Menu Tree Use the following illustrations to quickly find a setting or determine the range for a setting.
D DLLPP PPrroojjeeccttoorr— —U Usseerr’’ss M Maannuuaall – 50 –
D DLLPP PPrroojjeeccttoorr –– U Usseerr’’ss M Maannuuaall Menu Elements Some menus and windows contain large amounts of information in a small area. Refer to the following guide to navigate through options more easily. Title Highlight Slide bar Exit Title Radio button Menu windows or dialog windows typically contain the following elements: ITEM LABEL DESCRIPTION 1. Title Indicates the menu title. 2. Highlight Indicates the selected menu or item. 3.
D DLLPP PPrroojjeeccttoorr— —U Usseerr’’ss M Maannuuaall Input Menu Descriptions and Functions The Input menu displays all supported image sources. Select the required source from the menu using Ÿ or ź and press LABEL to confirm. DESCRIPTION Computer 1 Select the source connected to the Computer 1 input (see Connecting Your PC or Macintosh Computer on page 21). Computer 2 Select the source connected to the Computer 2 input (see Connecting Your PC or Macintosh Computer on page 21).
D DLLPP PPrroojjeeccttoorr –– U Usseerr’’ss M Maannuuaall Adjust Menu Descriptions and Functions The Adjust menu contains overall projector settings for image output such as sharpness, overscan and color matrix. Three tabs are accessible through the Adjust menu, Image, Image Options and Video. Image menu The Image tab is used to alter picture settings and can be accessed from the Adjust menu. The following table lists all functions with a description and the default setting.
D DLLPP PPrroojjeeccttoorr— —U Usseerr’’ss M Maannuuaall Image options menu The Image Options tab is used to configure image options such as screen positioning and aspect ratio. Access the Image Options tab in the Adjust menu. The following table lists all functions with a description and the default setting. LABEL DESCRIPTION Screen Select Screen using ŻorŹ from the list (see page 55). Overscan Set the Overscan value using ŻorŹ (see page 55). Adjust the position values using the slides.
D DLLPP PPrroojjeeccttoorr –– U Usseerr’’ss M Maannuuaall Screen The Screen option allows for the adjustment of the aspect ratio to alter the appearance or ratio of the projected image. 4:3 – Standard TV screen (4:3), proportionally four units wide for every three units high, no matter the size of the screen. 16:9 – A wide-screen aspect ratio for video. Side cut – Crops the image. True – Displays the current image in its true resolution. Normal – Displays the current image in its aspect ratio.
D DLLPP PPrroojjeeccttoorr— —U Usseerr’’ss M Maannuuaall Video menu The Video tab is used to configure image options such as film. Access the Video tab in the Adjust menu. The following table lists all functions with a description and the default setting. A detailed description follows the table. LABEL DESCRIPTION Noise reduction Select Noise reduction mode (see page 57). 3D Y/C separation Select 3D Y/C separation mode (see page 57). Progressive Select Progressive mode (see page 57).
D DLLPP PPrroojjeeccttoorr –– U Usseerr’’ss M Maannuuaall Noise reduction Select the level of noise reduction required. Range: Off, Low, Mid, High. 3D Y/C separation 3D Y/C Separation separates composite signal to Y (brightness) signal and C (color) signal, and can help to produce clearer and sharper images without overlapping colors (rainbow effect). Set 3D Y/C Separation On or Off. Progressive Progressive converts an interlaced image to a progressive scan image.
D DLLPP PPrroojjeeccttoorr— —U Usseerr’’ss M Maannuuaall Color matrix Color Matrices define the amount of the three-color components R (red), G (green), and B (blue) in a single point in color space. Select from the following: Auto – Auto selects the color matrix. RGB – Sets the color matrix to RGB, use for PC monitor or camera imaging. SDTV – Sets the color matrix to SDTV, use for Standard Definition imaging. HDTV – Sets the color matrix to HDTV, use for High Definition imaging.
D DLLPP PPrroojjeeccttoorr –– U Usseerr’’ss M Maannuuaall Detail Setting Menu Descriptions and Functions The Detail setting menu contains basic and advanced color adjustment options such as gamma correction, color contrast and color correction. Basic The Basic tab contains general setting such as gamma correction and color temperature. Access to the Basic tab is through the Detail setting menu. The following table lists all functions with a brief description.
D DLLPP PPrroojjeeccttoorr— —U Usseerr’’ss M Maannuuaall Gamma Gamma enables adjustment to the light intensity (brightness) of an image in order to match the source more closely. Select from the following: Dynamic – Allows the projector to alter the gamma correction automatically. Natural – Attempts to emulate the original source as closely as possible. Black detail – Black detail highlights boundaries between light and dark areas of the image more clearly.
D DLLPP PPrroojjeeccttoorr –– U Usseerr’’ss M Maannuuaall White balance White Balance allows the projector to compensate for different colors of light being emitted by different light sources. The following table lists all functions with a brief description. LABEL DESCRIPTION Red Set the value to compensate for red light sources. Green Set the value to compensate for green light sources. Blue Set the value to compensate for blue light sources.
D DLLPP PPrroojjeeccttoorr— —U Usseerr’’ss M Maannuuaall Color correction The Color correction tab enables the adjustment of color values in an image to remove unwanted effects, improve color, characteristics or add more of a particular color. The following table lists all functions with a brief description. LABEL DESCRIPTION Red Increase or decrease the amount of red in the projected output using Ż and Ź. Green Increase or decrease the amount of green in the projected output using Ż and Ź.
D DLLPP PPrroojjeeccttoorr –– U Usseerr’’ss M Maannuuaall Setting Menu Descriptions and Functions The Setting menu contains the most often used settings during installation and options to customize the general output of the projector. Three tabs are accessible through the Setting menu, Basic, Installation and Option. Basic The Basic tab contains general setup options such as lamp mode and OSD language settings and can be accessed with the projector control panel or with the remote control unit.
D DLLPP PPrroojjeeccttoorr— —U Usseerr’’ss M Maannuuaall Keystone The keystone trapezoid can be adjusted by selecting this option. Select Horizontal or Vertical using Ÿorź then, use ŻorŹ to adjust the projected image appearance as required. Note: When adjusting the keystone, place the projector in the following position. y Horizontal: set to the lens center y Vertical: set to the maximum top Lamp control Select Normal or Eco from the lamp mode window.
D DLLPP PPrroojjeeccttoorr –– U Usseerr’’ss M Maannuuaall Lamp interval The period of time for regulating lamp usage when not in dual lamp mode. Select from the following: Off, 1 week, 4 weeks and 2000H Language Select the OSD language to be used.
D DLLPP PPrroojjeeccttoorr— —U Usseerr’’ss M Maannuuaall Installation The Installation tab contains menu options for various setup conditions such as orientation and remote sensor mode and is accessed through the Setting menu. The following table lists all functions with a brief description. LABEL DESCRIPTION Ceiling & Rear Select from four projection methods depending on projection site (see Ceiling & Rear page 67). Communication speed Select Communication speed.
D DLLPP PPrroojjeeccttoorr –– U Usseerr’’ss M Maannuuaall LABEL DESCRIPTION DynamicBlack DynamicBlackTM improves the black level of the projector. Black level is the darkest part of a picture and varies between viewing devices and environments. Set DynamicBlack on/off. RC sensor Set RC sensor fields. Range: Both, Front, Back Network setting Opens Network preferences tab (see Network setting on page 69). Standby mode Select Standby mode.
D DLLPP PPrroojjeeccttoorr— —U Usseerr’’ss M Maannuuaall Display time Sets the amount of time a menu is displayed. Select from the following: Manual – Menus stay on screen until the Menu button is pressed again. Auto 5 secs—Menu is displayed for 5 seconds. Auto 15 secs – Menu is displayed for 15 seconds. Auto 45 secs – Menu is displayed for 45 seconds. Background Background enables you to display a blue/black screen when there is no signal. The default background is blue.
D DLLPP PPrroojjeeccttoorr –– U Usseerr’’ss M Maannuuaall Key lock Turn On/Off the Key Lock function for cabinet buttons. Note: y This Control Panel Lock does not affect the remote control functions. y When the control panel is locked, press and holding the Cancel button on the projector cabinet for about 10 seconds. The setting will change to Off. DynamicBlack DynamicBlackTM enables you to improve the black level of the projector. RC sensor Set the operating range for the wireless remote control.
D DLLPP PPrroojjeeccttoorr— —U Usseerr’’ss M Maannuuaall Standby mode There are two standby modes available: Normal and Power-saving. Power-saving mode allows you to put the projector in the standby condition to consume less power than Normal. Note: Be sure to connect the projector and computer while the projector is in standby mode and before turning on the computer. Select from the following: Normal Power-saving Note: The HTTP server functions are not available during Power-saving mode.
D DLLPP PPrroojjeeccttoorr –– U Usseerr’’ss M Maannuuaall Network setting The Network setting menu is accessed by using the Setup/Installation menu and contains the general LAN settings. The following table lists all functions with a description and the default setting. LABEL DESCRIPTION DHCP Select either a static IP (Disable) or DHCP IP (Enable) setting by selecting the appropriate radio button. IP address Displays the IP address. Subnet Displays the subnet mask.
D DLLPP PPrroojjeeccttoorr— —U Usseerr’’ss M Maannuuaall Option The Option tab contains miscellaneous setup menu settings such as Power management and Default input select and can be accessed by using the Setting menu. The following table lists all functions with a description and the default setting. LABEL Power management Screen trigger Fan control Default input select Color System Message Filter warning Search mode DESCRIPTION Select the amount of time the projector remains idle before powering down.
D DLLPP PPrroojjeeccttoorr –– U Usseerr’’ss M Maannuuaall Power management Power management enables the projector to automatically turn off if there is no signal received by any input. Select from the following: Off 5 minutes 10 minutes 20 minutes 30 minutes Screen trigger Set Screen trigger to On to enable the projector to automatically lower the projection screen when powering on.
D DLLPP PPrroojjeeccttoorr— —U Usseerr’’ss M Maannuuaall Default input select The Default input is the image source that the projector will search for automatically on startup. Last – Uses the most recently used image source. Auto – Auto detects the default image source. Computer1/2/3 – Uses Computer1, 2 or 3 as the default image source. Component – Uses last component as the default image source. Video – Uses last video input as default image source.
D DLLPP PPrroojjeeccttoorr –– U Usseerr’’ss M Maannuuaall Filter warning Set Filter warning to have the projector display a message when the air filter needs servicing. The message below shows when this function is activated. Search mode This feature sets the Auto Adjust mode so that the RGB image can be automatically or manually adjusted for noise and stability. You can automatically make adjustments in two ways: [Normal] and [Fine]. Normal: The RGB image will be automatically adjusted.
D DLLPP PPrroojjeeccttoorr— —U Usseerr’’ss M Maannuuaall Information Menu Descriptions and Functions The Information menu provides only screens for the quick access of menus. The Information menu contains four distinct tabs. Usage time The Usage time tab displays information about lamp usage and remaining lamp life. The following table lists all items with a description. LABEL DESCRIPTION Lamp1 life remaining Displays the Lamp1 life remaining as a percentage.
D DLLPP PPrroojjeeccttoorr –– U Usseerr’’ss M Maannuuaall Input The Input tab displays various source and frequency values at a glance. The following table lists all items with a description. LABEL DESCRIPTION Input name Displays the Input Terminal that is presently being used (see Default input select on page 74). Signal Displays the Source name of the signal presently being used. H-sync. freq. Displays Horizontal frequency in KHz. V-sync. freq. Displays Vertical frequency in Hz.
D DLLPP PPrroojjeeccttoorr— —U Usseerr’’ss M Maannuuaall Network The Network tab displays LAN settings as previously defined (see Network setting on page 71).
Pro6500DP
D DLLPP PPrroojjeeccttoorr— —U Usseerr’’ss M Maannuuaall Reset Menu Descriptions and Functions Occasionally, circumstances may require that factory defaults be reset, for demonstration purposes for example, or when components are replaced. The Reset menu contains options for returning settings to the factory default and is accessed by using the Main menu. The following table lists all items with a description.
D DLLPP PPrroojjeeccttoorr –– U Usseerr’’ss M Maannuuaall Replacing the Lamps When a lamp reaches the end of it’s usable life, the following message is displayed. Replace the lamp. The projection lamps should be replaced when they burn out. They should only be replaced with a certified replacement part, contact your local dealer if unsure. Note: 1. Lamps are positioned differently. Take care not to force the lamps when replacing. 2.
D DLLPP PPrroojjeeccttoorr— —U Usseerr’’ss M Maannuuaall The projection lamp should be replaced when it burns out. It should only be replaced with a certified replacement part, which you can order from your local dealer. Important: a. The lamp contains a certain amount of mercury and should be disposed of according to local ordinance regulations. b. Avoid touching the glass surface of the new lamp: Doing so may shorten its operation life.
D Maannuuaall DLLPP PPrroojjeeccttoorr –– U Usseerr’’ss M 3. 4. Pull firmly on the module handle in the direction shown to remove the lamp. Reverse steps 1 to 3 to install the new lamp module(s) and replace the lamp cover.
D DLLPP PPrroojjeeccttoorr— —U Usseerr’’ss M Maannuuaall Resetting the Lamp Time Counter After replacing the lamp(s), the lamp hour counter(s) should be reset to zero. Refer to the following guide: 1. 2. 3. 4. Press the Menu button on the OSD control panel or Remote Control to open the Main menu. Press the Ÿorź button to move to the Reset menu and press . The Reset menu is displayed. Select Clear lamp1 time or Clear lamp2 time as required using Ÿorź and press . A confirmation box is displayed.
APPENDIX Troubleshooting Indicator Messages Several indicator messages are used by the projector to alert users of problems with setup or internal parts. The LEDs on the top surface of the projector show the status of the WARNING and lamp 1/2 as well as the general working order of the projector through the WARNING LED (see OSD Controls and Status LEDs on page 6 for location). The following tables describe the various states of the 4 LEDs.
D DLLPP PPrroojjeeccttoorr— —U Usseerr’’ss M Maannuuaall The LAMP LEDs PROJECTOR STATUS LED CONDITION LED SEQUENCE PROJECTOR CONDITION Lamp off Off Off Lamp off End of the lamp life Red blink 0.5 secs on 0.5 secs off Replace lamp No lamp Red 1 time blink (repeatedly) 0.5 secs on 2.5 secs off ERROR Lamp ERROR Red 6 times blink (repeatedly) (0.5 secs ON > 0.5 secs OFF) * 6 > 2.0 secs OFF ERROR Cooling lamp Orange blink 0.5 secs ON > 0.
D DLLPP PPrroojjeeccttoorr –– U Usseerr’’ss M Maannuuaall Image Problems Problem: No image appears on the screen 1. Verify the settings on your notebook or desktop PC. 2. Turn off all equipment and power up again in the correct order. Problem: The image is blurred 1. Adjust the Focus on the projector. 3. Press the AUTO button on the remote control or projector. 4. Ensure the projector-to-screen distance is within the specified range. 5. Check that the projector lens is clean. 6. Remove the lens cover.
D DLLPP PPrroojjeeccttoorr— —U Usseerr’’ss M Maannuuaall Remote Control Problems Problem: The projector does not respond to the remote control 1. Direct the remote control towards remote sensor on the projector. 2. Ensure the path between remote and sensor is not obstructed. 3. Turn off any fluorescent lights in the room. 4. Check the battery polarity. 5. Replace the batteries. 6. Turn off other Infrared-enabled devices in the vicinity. 7. Have the remote control serviced. 8.
SPECIFICATIONS Projector Specifications This section provides technical information about the projector's performance. Optical Specifications ITEM DESCRIPTION Projection system Single DLP® chip, 4 segment color wheel Resolution 1024 x 768 pixels* (up to UXGA @ 60 Hz) Lamp 280 W AC (230 W in Eco mode), Dual lamp system Image size (diagonal) 50" - 200" / 1.27m - 5.08m (GC805G) 40" - 500" / 1.02m – 12.7m (GB942G, GB940G, GB949G, GB957G) Lens options GC805G: Power focus, throw ratio 0.77:1, F2.
D DLLPP PPrroojjeeccttoorr— —U Usseerr’’ss M Maannuuaall Electrical Specifications ITEM DESCRIPTION Inputs 1 Analog RGB (Mini D-Sub 15P), 1 Analog RGB R/Cr, G/Y, B/Cb, H, V (BNC x 5), 1 Digital RGB (DVI-D 24P), 1 Component Y, Cb/Pb, Cr/Pr (RCA x 3), 1 Component (Mini D-Sub 15P) shared with COMPUTER 1 IN, 1 S-Video (Mini DIN 4P), 1 Video, 3 Stereo Mini Audio, 2 (L/R) RCA Audio Outputs 1 RGB (Mini D-Sub 15P), 1 Stereo Mini Audio, 1 Screen Trigger Control 1 PC Control Port (D-Sub 9P) USB Port 1 B Typ
D DLLPP PPrroojjeeccttoorr –– U Usseerr’’ss M Maannuuaall Mechanical Specifications ITEM DESCRIPTION Dimensions 19.9" (W) x 7.6" (H) x 15.2" (D) 505 mm (W) x 192 mm (H) x 385 mm (D) (not including protrusions) Weight 45.1 lb/20.
D DLLPP PPrroojjeeccttoorr— —U Usseerr’’ss M Maannuuaall Cabinet Dimensions – 94 –
D DLLPP PPrroojjeeccttoorr –– U Usseerr’’ss M Maannuuaall Pin Assignments of Mini D-Sub 15 Pin Input Connector Signal Levels Video signal: Sync signal: PIN NUMBER 0.
D DLLPP PPrroojjeeccttoorr— —U Usseerr’’ss M Maannuuaall Compatible Input Signal List The following table shows compatible signal types, their resolution and frequency refresh rates. Horizontal: 15kHz, 31kHz to 90 kHz Vertical: 50 Hz to 85 Hz RESOLUTION H-SYNC (KHZ) V-SYNC (HZ) VGA SIGNAL 640X350 31.5 70.1 RGB O DVI O VESA(DMT) 640X350 37.9 85.1 O O 720X350 31.5 70.0 O O CGA84 640X400 31.5 70.1 O O VESA(DMT) 640X400 37.9 85.1 O O 720X400 31.5 70.
D DLLPP PPrroojjeeccttoorr –– U Usseerr’’ss M Maannuuaall DMT 1400X1050 82.3 75.0 O O CVT 1440X900 55.9 60.0 O O CVT 1440X900 70.6 75.0 O O CVT 1440X900 80.4 85.0 O O VESA(DMT) 1600X1200 75.0 60.0 O O CVT 1680X1050 65.3 60.0 O O 1035i 1920X1035i 33.75 60.0 O O 1080i/50 1920X1080 28.125 50.0 O O 1080i/60 1920X1080 33.75 60.0 O O D-1080p/30 1920X1080 33.75 30.0 O O D-1080p/25 1920X1080 28.125 25.0 O O D-1080p/24 1920X1080 27.0 24.
D DLLPP PPrroojjeeccttoorr— —U Usseerr’’ss M Maannuuaall PC Control Codes and Cable Connections This projector provides a function to control and monitor the projector's operations by using the RS232C serial port. 1. 2. Connect a RS-232C serial cross cable to SERIAL PORT IN on the projector and serial port on the PC.
D DLLPP PPrroojjeeccttoorr –– U Usseerr’’ss M Maannuuaall Control Command Diagram The command is structured by the Header code, command code, data code and end code. Most of the commands are structured except some for the compatibility issue with other projectors. HEX ASCII Header code 7Eh ‘~’ Command code Command Command Data code Data Data End code 0Dh CR Control Sequence The projector may send a return code after it received a command.
D DLLPP PPrroojjeeccttoorr— —U Usseerr’’ss M Maannuuaall Set Value Command ITEM Brightness Contrast Color(Saturation) Tint Scaling Color Temperature Projection Mode ASCII ~ s B ? CR ϡ ~ s C ? CR ~ s R ? CR ~ s N ? CR ~ s A ? CR ~ s T ? CR ~ s J ? CR HEX 7Eh 73h 42h ?h 0Dh 7Eh 73h 43h ?h 0Dh 7Eh 73h 52h ?h 0Dh 7Eh 73h 4Eh ?h 0Dh 7Eh 73h 41h ?h 0Dh 7Eh 73h 54h ?h 0Dh 7Eh 73h 4Ah ?h 0Dh ϡ ? : ASCII Data Data Range ITEM Brightness Contrast Saturation Tint Scaling Color Temperature Projection Mode Set Dat
D DLLPP PPrroojjeeccttoorr –– U Usseerr’’ss M Maannuuaall Screen Trigger When the projector is powered ON the screen trigger output sends a low voltage trigger to the screen controller and the screen will go down. When the projector is powered OFF the screen trigger stops sending a low voltage trigger to the screen controller and the screen will go up. Note: To use this feature, you must turn on the Screen Trigger function. See Screen Trigger on page 73 for more information.
D DLLPP PPrroojjeeccttoorr— —U Usseerr’’ss M Maannuuaall Operation s Uing HTTP Browser Overview The use of HTTP server functions will allow control of the projector from a web browser without the installation of special software. Please be sure to use “Microsoft Internet Explorer 4.x” or a higher version for the web browser. (This device uses “JavaScript” and “Cookies” and the browser should be set to accept these functions. The setting method will vary depending on the version of browser.
D DLLPP PPrroojjeeccttoorr –– U Usseerr’’ss M Maannuuaall Configuring Network Settings The Network Settings screen is displayed as follows: http://< the projector's IP address>/lanconf.html DOMAIN Host Name: Type in a hostname. Up to 60 alphanumeric characters can be used. Domain Name: Type in domain name of the network connected to the projector. Up to 60 alphanumeric characters can be used. Apply : Click to reflect the entries. MAIL Alert Mail: Click “Enable” to enable Alert Mail feature.
D DLLPP PPrroojjeeccttoorr— —U Usseerr’’ss M Maannuuaall TEST MAIL Send a test mail to check if your settings are correct. Click to “Execute” to enable this feature. Test Mail Status Button: Click to display the test result. Sample of a message sent from the projector: Projector Name: X X X X Lamp 1 or 2 Hours Used: xxxx [H] The lamp is at the end of its usable life. Please replace the lamp. Note: If you entered an incorrect address in a test, you may not receive an Alert mail.
D DLLPP PPrroojjeeccttoorr –– U Usseerr’’ss M Maannuuaall Structure of the HTTP Server Once the projector is connected to a network and configured correctly, the following screen is displayed through the web browser. http://< the projector's IP address>/index.
D DLLPP PPrroojjeeccttoorr— —U Usseerr’’ss M Maannuuaall FUNCTION PROJECTOR STATUS Panel SETTING Refresh – Updates the panel with the latest information available DESCRIPTION This displays the status of selected projector functions Lamp1 life remaining – Displays the remaining life of Lamp 1 as a percentage Lamp2 life remaining – Displays the remaining life of Lamp 2 as a percentage Lamp1 time – Displays the number of hours Lamp 1 has been used Lamp2 time – Displays the number of hours Lamp 2 has been us
REGULATORY COMPLIANCE FCC Warning This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
