Wired/Wireless Dual-Function Microphone 有线/无线双功能麦克风 BY-PM500W User Manual 用户手册
General Introduction Thanks for choosing BOYA! BOYA BY-PM500W is a dual-function microphone, offering wired or wireless operation for gamers, streamers, podcasters in a variety of applications. The microphone features selectable cardioid and omnidirectional pickup patterns, allowing you to customize your audio, and supporting 24bit/48 kHz resolution. Built-in 3.5mm headphone jack allows you to monitor and ensure the audio intelligibility during recording.
Product Structure TX 1. Metal mesh windscreen 2. Headphone volume/ gain/mute control 3. Polar pattern indicators 4. Polar pattern switch 5. Locking knobs 6. Desk stand 7. Battery level indicator 8. Power/pair button 9. USB-C port 10. 3.5mm headphone jack 11.
RX 1. Status indicator 2. USB-C connector 3. 3.5mm headphone jack 4. Volume control(+/-) / Pair button 5.
Functions Angle Adjustment Loosen the knobs of both sides anticlockwise. Adjust the microphone at your desired angle, then tighten the knobs.
Headphone Volume/Gain/Mute Control Mode Operation Indicator Headphone volume control Gain control Mute ON Default setting: headphone volume control Short press the knob to mute the microphone. Long press the knob to switch between gain control and headphone volume control. Turn the knob to adjust mic gain/ headphone volume.
Factory Reset For optimum sound, please press and hold the headphone volume/gain/mute control knob and the polar pattern switch simultaneously to restore factory setting. The indicator will blink red three times.
Operation Guide Wired Operation 1. Connect the microphone to your smartphone/computer.
B Mac/Windows Computer Using the supplied USB-A to USB-C cable 8
2. Connect headphones for audio monitoring. 3. Adjust the headphone volume/gain/mute control knob according to your needs. 4. You are ready to record.
Wireless Operation 1. Turn on the transmitter Press and hold the power button Note: When using wired function, short press the power button to enable wireless function simultaneously. Double-click the power button to enter pairing mode. Press again to disable wireless function.
2.
3. TX & RX Pairing Before leaving factory, the transmitter and the receiver is pre-paired. Therefore, the connection will be established once they are powered on. If they are disconnected, please follow below steps: ① Double-click the TX’s pair button to enter pairing mode.
② Press the RX’s pair(+ and -) button to enter pairing mode.
4. The transmitter and the receiver will be successfully paired within 10 seconds. Mode Indicators (of both TX and RX) Unpaired Slowly flashing blue light Pairing Quickly flashing blue light Paired Successfully Solid blue light 5. Connect headphones for audio monitoring.
6. You are ready to record. Note: Due to 2.4GHz wireless frequency, signal can be easily attenuated. Please try to avoid obstacles, such as walls and buildings, and avoid close proximity to devices with 2.4GHz signal, such as high-power wifi antennas, smartphones with wifi in use, radios, etc.
Specifications Wired Operation Mic Capsule 14mm Condenser Capsule Polar Pattern Cardioid /Omnidirectional Frequency Response 20Hz-20kHz Sensitivity -36dB（0dB=1V/Pa，1kHz 1Pa） Signal-to-Noise Ratio 80dB Maximum SPL 110dB Sampling Rate 48kHz Bit Rate 24bit Mic Gain 0~54dB Working Voltage 5V/100mA Audio Output Connector 3.
Wireless Operation Mic Capsule 14mm Condenser Capsule Polar Pattern Cardioid /Omnidirectional Frequency Response 35Hz-18kHz Sensitivity -36dB（0dB=1V/Pa，1kHz 1Pa） Signal-to-Noise Ratio 80dB Maximum SPL 110dB Transmission Type 2.4GHz Modulation GFSK Antenna Dipole Antenna Operating Range 10m (Indoors with obstacles) RF Output Power <10mW Distortion ＜0.05% Battery Life 8 Hours Charging Time 1.5 Hours Battery Capacity 800mAh Dimensions TX：226.7×100×100mm RX：71.6×27.1×10.
Polar Pattern Cardioid Polar Pattern 0° 30 20 10 270° 90° dB -13 -14 -15 -16 -17 -18 -19 -20 0 -10 -20 -30 -40 20 200 2000 20000 180° Omnidirectional 0° 30 20 10 270° 90° dB -28 -30 -32 -34 -36 -38 -40 -42 0 -10 -20 -30 180° -40 20 200 18 2000 20000
FCC Warning This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction. FCC RF exposure statement: The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction. www.boya-mic.
