User's Manual

9 series_v2.9 Sep06
Drilling Template
Copyright © 2006 BQT Solutions Limited. BQT Solutions and the BQT Solutions
logo are registered trademarks of BQT Solutions (Australia) Pty Ltd.
Mifare is a registered trademark of Philips Electronics.
Specifications
Output protocols Wiegand 26-199 bit, RS485 or custom configurations (model dependent)
Power requirements 12Vdc
Current consumption
Normal 120mA
Activated 140mA
Read range 20 - 60mm (0.8” – 2.4”)(typically)
Operating temperature -25ºC to +65ºC (-13ºF to 149ºF)
Relative humidity 90% max, operating non-condensing
Reader dimensions 140mm (L) x 45mm (W) x 32mm (D) (5.51” x 1.77” x 1.26”)
Status LED’s Green & Red
Audible tone
Internal or external buzzer control
Colour Two toned – Silver & Charcoal
IP rating IP 67
Information contained in this document is subject to change without notic e.
For further technical information visit our website at www.bqtsolutions.com
or email [e-mail].
Alternatively contact us at one of our global locations
UNITED KINGDOM & EMEA
Global House, 1 Ashley Avenue, Epsom
Surrey KT 18 5AD United Kingdom
Phone: + 44 (0)20 8823 9350 Fax: + 44 (0)20 8823 9001
AMERICA
30021 Tomas Street, Suite 300
Rancho Santa Margarita CA 92688 United States of America
Phone: [phone] (ext 42) Fax:[phone]
AUSTRALIA & ASIA PACIFIC
Level 4, 65 Epping Road
North Ryde NSW 2113 Australia
Phone: [phone] Fax: [phone]
CHINA
Suite 1602, No.75, ShengDa Garden, 2518 LongHua Road,
XuHui District, Shanghai 200232, P.R.China
Tel: [phone] Fax: [phone]
DF900 - DESFire
BT900 - Mifare
miP9 - SPEK
CSN9 - Card Serial Number
miPASS 9 Series Mifare
reader models
For all 9 Series readers
●
20mm (0.79”) diameter
hole for wire entry
●
2 x 4 mm (0.16”) diameter
holes for mounting screws
●
Minimum reader dimensions
are 140mm x 45 mm
(5.51" x 1.77")
INSTALLATION GUIDE
Version 2.9
Regulatory Information
CE Mark
The 9 Series has passed all relevant tests and obtained CE approval.
C Tick
The 9 Series has passed all relevant requirements for application of C Tick.
FCC
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
BT900D, BT900DG, DF990D, DF900DG FCC ID: QVL - BT900P
BT900WG FCC ID: QVL -BT900A
miP9, CSN9, BT900W FCC ID: QVL MIP9
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna
- Increase the separation between the equipment and receiver
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
- Consult the dealer or an experienced radio/TV technician for help
Any changes or modifications not expressively approved by BQT Solutions could void the user's authority to operate this equipment.
Designed & Manufactured
in
Australia
NOTE:  The 0V reference cable shall be included within the controller cable.
 The 12Vdc power cable shall NOT be included in the controller Cable.
 Only ONE power source is connected from the reader at any one time.
 RS485 - OPTIONAL USE
45mm
62mm
➣ ➣
➣ ➣
20mm Ø
4mm Ø
4mm Ø
Wiring Schematic
Reader connections
BUZ
LED
W0
W1
+12Vdc
0V
Power Cable
Controller Cable
RED
+12Vdc
BLACK
0V
YELLOW BUZ
ORANGE LED
GREEN W0
WHITE W1
YELLOW/W
GREEN/W
BT900W, BT900WG
miP9, CSN9
RS485A
RS485B
Power Supply
Controller
NOTE: If used with a shielded
cable, the shield is connected
to Controller 0V reference
DF900D, DF900DG, BT900D, BT900DG
0V
9 series_v2.9.ai 21/09/2006 10:26:36 AM