User manual

ManualsBrandsBRÜDER MANNESMANN ManualsStriking ToolsElectric stapler

GB - 7

Electric Staple Gun

Item No. 12420

Instruction Manual

Always read and observe the safety instructions included and this manual

before using electrical tools!

Additional safety instructions for electric staple guns

This electric staple gun is used for stapling or nailing wooden strips, films, sheets of material, paper, cardboard,

wire mesh and so onto wood or other suitable base materials.

 Unplug the tool from the mains before carrying out any work on it, especially filing the magazine with staples

or nails.

 Never point the tool at animals or people.

 Always check the plug and cable before use, and have any damaged parts replaced by a qualified specialist.

 Always makes sure that the mains cable(2) is trailing away from the back of the tool.

 Never use different types of fastening material at the same time. Always make sure that fastening materials in

the magazine are of the same type.

 Never push the trigger lever down on an empty magazine.

 Leave the main switch (4) in the "Off" position ( 0 ) during work breaks.

 Wear eye protection when working with the electric staple gun.

 Remove all nails or staples from the magazine during longer work breaks or after finishing work.

 Do not use this staple gun for fastening electrical cables. It is not designed for electric cable installation and

may damage the insulation of electric cables thereby causing electric shock or fire hazards.

 Immediately stop using the staple gun if it is either faulty or not working properly, and bring it to an expert to

be checked over.

 Use the staple gun away from children, and keep it out of children’s reach.

Tool description (Fig. 1 + 2)

1. Trigger

2. Mains power cable

3. Hammer force preselection

4. Main switch

5. Staple magazine

6. Contact switch

7. Magazine lock

Technical data

Voltage 220-240 V~/50 Hz

Magazine capacity 50 nails/staples

Stapling/nailing rate 30 shots per minute

Suitable staple sizes 15-25 mm

Suitable nail size 15-32 mm

Sound pressure level (LPA) 80,48dB(A)

(Uncertainty K = 3 dB)

Sound power level (LWA) 91,48 dB(A)

(Uncertainty K = 3 dB)

Vibration data 2,13 m/s²

(Uncertainty K = 1,5 m/s²)

Safety class / II

Summary of content (4 pages)

PAGE 1
Electric Staple Gun Item No. 12420 Instruction Manual Always read and observe the safety instructions included and this manual before using electrical tools! Additional safety instructions for electric staple guns This electric staple gun is used for stapling or nailing wooden strips, films, sheets of material, paper, cardboard, wire mesh and so onto wood or other suitable base materials.
PAGE 2
Always wear eye protection during use! • • • The vibration emission level given in this information sheet has been measured in accordance with a standardized test given in EN 60745 and may be used to compare one tool with another. The vibration emission level will vary because of the ways in which a power tool can be used and may increase above the level given in this information sheet. This could lead to a significant underestimate of exposure when the tool is used regularly in such a way.
PAGE 3
Troubleshooting A staple or nail may jam in the magazine when stapling onto hard surfaces. If this happens, stop work and do not attempt to drive in any more staples or nails.     Before any work on the machine itself, pull the mains plug. Press release buttons (7) and pull out the magazine (5) toward the rear. Remove the jammed staple. For this, use a pair of pliers, if required. Insert the magazine (5) again until the magazine lock (7) engages. Load the magazine in good time.
PAGE 4
Discarding old electrical tools—environmental protection     If your tool has been so heavily used that it has become worn out and has to be replaced, or you have no further use for it, you must turn the electrical tool in at a central recycling centre for disposal. Please contact your community waste collection service or local authority to find out where you can hand in your tool for recycling. Electric tools contain valuable raw materials that can be recycled.