Installation / Operation Instruction Manual
Table Of Contents
- Brute MagnaTech
- Table of Contents. Page 1
- SECTION 1 General Information
- SECTION 2 Venting and Combustion Air
- SECTION 3 Gas supply and Piping
- SECTION 4 Water Flow and Headloss Data
- SECTION 5 Piping
- SECTION 6 Condensate Drain Trap
- SECTION 7 Electrical Connections
- SECTION 8 Control Operation
- 8.A The Home Screen
- 8.B Login to Lock / Unlock the Display Screen
- 8.C Quick Start
- 8.D Configuration
- 8.E Service Screens
- 8.F Messages and USB
- 8.G Active Demands
- SECTION 9 Parameter Tables
- SECTION 10 Initial startup Instructions
- SECTION 11 Maintenance
- SECTION 12 Troubleshooting
- SECTION 13 Replacement Parts
- 13.A General Information
- 13.B Component Illustrations, Parts Lists, and Part Numbers
- 13.B.1 Final Assembly, Part Numbers
- 13.B.2 Frame and Jacket Assembly, Part Numbers
- 13.B.3 Control Panel, Part Numbers
- 13.B.4 Air / Gas System, Part Numbers (Model 1600)
- 13.B.5 Air / Gas System, Part Numbers (Model 2000)
- 13.B.6 Air / Gas System, Part Numbers (Models 2500 & 3000)
- 13.B.7 Air / Gas System, Part Numbers(Models 3500 and 4000)
- 13.B.8 AC Distribution Box, Part Numbers (Model 1600)
- 13.B.9 AC Distribution Box, Part Numbers (Model 2000)
- 13.B.10 AC Distribution Box, Part Numbers (Models 2500 to 4000)
- 13.B.11 Inlet Waterway Assemblies, Part Numbers
- 13.B.12 Outlet Waterway Assemblies, Part Numbers
- 13.B.13 Gas Train Assembly, Part Numbers(Models 1600, 2000, 2500 and 3000)
- 13.B.14 Gas Train Assembly, Part Numbers (Models 3500 and 4000)
Page 118
2
15
4
3
1
12
13
13
5
A
DWG. NO:SOFTWARE
CHECK
DWG
PROJECT NO.
D
C
B
A
B
C
D
1
2
3
45
6
7
8
7
6
5
D
SHEET 1 OF 1
REV.
SCALE: NONE
INTENDED SIZE:
4
23
1
BY LAARS HEATING SYSTEMS CO.
8
SH
DW G N
O .
1
DRAFT
REV
DWG
REVISIONS
REV.
CHANGE:
APPR
ENGR APPR
DWG
DWG
ECN
DWG
APPROVALS
1
.010
DECIMALS .XX
DRAFT
PURPOSE EXCEPT AS SPECIFICALLY AUTHORIZED IN WRITING
SEE PARTS LIST
FINISH
DWG
1/8"
TITLE:
MATERIAL:
MGT 5:1 SIT - FINAL ASSEMBLY
DISCLOSED TO OTHERS FOR MANUFACTURING OR ANY OTHER
TOLERANCES ARE:
REPRODUCED, TRANSFERRED TO OTHER DOCUMENTS, USED OR
.1
DECIMALS .XXX
DWG
DWG
S
FRACTIONS
.03
DECIMALS .X
DIMENSIONS ARE IN INCHES.
UNLESS OTHERWISE SPECIFIED:
APPR
ENGR
THIS DOCUMENT AND THE INFORMATION CONTAINED HEREIN ARE
PROPRIETARY TO LAARS HEATING SYSTEMS CO. AND SHALL NOT BE
ANGLES
DO NOT SCALE DRAWING.
THIRD ANGLE PROJECTION.
PROJ
9
8
DETAIL A
SCALE 2 : 5
10
1-B
1-A
Final Assembly
SECTION 13 Replacement Parts
Use only genuine Manufacturer’s replacement parts.
13.A General Information
To order or purchase parts, contact your nearest manufacturers dealer or
distributor. (See the back cover of this manual for the manufacturers website).
13.B Component Illustrations, Parts Lists, and Part Numbers