Installation / Operation Instruction Manual
Table Of Contents
- Brute MagnaTech
- Table of Contents. Page 1
- SECTION 1 General Information
- SECTION 2 Venting and Combustion Air
- SECTION 3 Gas supply and Piping
- SECTION 4 Water Flow and Headloss Data
- SECTION 5 Piping
- SECTION 6 Condensate Drain Trap
- SECTION 7 Electrical Connections
- SECTION 8 Control Operation
- 8.A The Home Screen
- 8.B Login to Lock / Unlock the Display Screen
- 8.C Quick Start
- 8.D Configuration
- 8.E Service Screens
- 8.F Messages and USB
- 8.G Active Demands
- SECTION 9 Parameter Tables
- SECTION 10 Initial startup Instructions
- SECTION 11 Maintenance
- SECTION 12 Troubleshooting
- SECTION 13 Replacement Parts
- 13.A General Information
- 13.B Component Illustrations, Parts Lists, and Part Numbers
- 13.B.1 Final Assembly, Part Numbers
- 13.B.2 Frame and Jacket Assembly, Part Numbers
- 13.B.3 Control Panel, Part Numbers
- 13.B.4 Air / Gas System, Part Numbers (Model 1600)
- 13.B.5 Air / Gas System, Part Numbers (Model 2000)
- 13.B.6 Air / Gas System, Part Numbers (Models 2500 & 3000)
- 13.B.7 Air / Gas System, Part Numbers(Models 3500 and 4000)
- 13.B.8 AC Distribution Box, Part Numbers (Model 1600)
- 13.B.9 AC Distribution Box, Part Numbers (Model 2000)
- 13.B.10 AC Distribution Box, Part Numbers (Models 2500 to 4000)
- 13.B.11 Inlet Waterway Assemblies, Part Numbers
- 13.B.12 Outlet Waterway Assemblies, Part Numbers
- 13.B.13 Gas Train Assembly, Part Numbers(Models 1600, 2000, 2500 and 3000)
- 13.B.14 Gas Train Assembly, Part Numbers (Models 3500 and 4000)
Page 82
CONFIGURATION
8.D.8.a Delta T Parameters
To navigate to the Delta T Parameters Screen, touch the Temp Limits Icon on the Conguration Screen, then touch the
Delta T Parameters button on the Temperature Limits Parameters Screen.
The Delta T Parameters Screen allows adjustment of the following parameters:
•
Enable/Disable – Enables/disables the Delta T temperature functionality.
•
Delta T Temp Max – The temperature dierence between the unit’s inlet and outlet at
which the boiler/heater will run at the minimum ring rate.
•
Delta T Temp Min – The temperature dierence between the unit’s inlet and outlet
at which the boiler/heater will begin to de-rate to prevent a Delta T shut down
condition.
8.D.8.b Flue Limitation Parameters
To navigate to the Flue Limitation Parameters Screen, touch the Temp Limits Icon on the Conguration Screen, then touch
the Flue Limitation button on the Temperature Limits Parameters Screen.
The Flue Limitation Parameters Screen allows adjustment of the following parameters:
•
Manual Reset Flue – The temperature at which the unit will shut down due to exceeding a ue temperature manual reset
condition.
•
Flue Temp MIN & Flue Temp Max- The control will attempt to prevent the unit
from reaching the Manual Reset Flue lockout condition by modulating the fan
speed (and therefore, the input). Flue Temp Min is the temperature setting at
which the unit will begin to de-rate the input. It de-rates linearly until it hits the
Flue Temp Max setting, where the fan is at minimum speed.
8.D.8.c Outlet Limitation Parameters
To navigate to the Outlet Limitation Parameters Screen, touch the Temp Limits Icon on the Conguration Screen, then touch
the Outlet Limitation button on the Temperature Limits Parameters Screen.
The Outlet Limitation Parameters Screen allows adjustment of the following parameters:
• Outlet Temp Min – The outlet temperature at which the boiler/heater will begin to de-rate, in an attempt to prevent a
manual reset high temperature outlet shut down condition.
•
Outlet Temp Max – The outlet temperature at which the boiler/heater will shut down on a manual reset high temperature
outlet condition.