Installation / Operation Instruction Manual

Page 4
Bradford White Corp
1.B Model Identication
Consult the rating plate on the unit. The
following information describes the model number
structure.
Model Character Designation
1-4 Model Series Designation
B M T 2 = Bradford White, Brute Deluxe
5 Usage
H = Hydronic
V = Volume Water
6-9 Size
0 2 0 0 = 199,900 BTU/h input
0 3 0 0 = 300,000 BTU/h input
0 4 0 0 = 399,900 BTU/h input
10 Fuel
N = Natural Gas
P = Propane
11 Location
C = Indoor and Outdoor
12 Firing Mode
C = On-O󰀨 (standard)
K = Two-stage (optional)
13 Revision
2 = Revision Level 2 (BMT2H only)
3 = Revision Level 3 (BMT2V only)
14 Heat Exchanger
B = Glass-lined CI / copper / brz trim (std.
BMT2V)
C = Glass-lined cast iron / copper (std. BMT2H)
N = Glass-lined cast iron / cu-nickel
P = Glass-lined cast iron / cu-nickel / brz trim
2 = Glass-lined cast iron / copper, brz trim, HLW
5 = Glass-lined cast iron / cu-nickel / brz, HLW
15 Options Code
X = Standard unit
L = Low temperature control (std. BMT2V)
16 Pump Options
X = No Pump
N = Pump mounted, normal water, Taco
S = Pump mounted, soft water pump (BMT2V
only), Taco
G = Pump mounted, normal water, Grundfos
1.C Warranty
Bradford White Brute Deluxe appliances are
covered by a limited warranty. The owner should
complete the warranty registration at
www.BradfordWhite.com
All warranty claims must be made to an
authorized Bradford White representative or directly
to the factory. Claims must include the serial number
and model (this information can be found on the rating
plate), installation date, and name of the installer.
Shipping costs are not included in the warranty
coverage.
Some accessory items are shipped in separate
packages. Verify receipt of all packages listed on
the packing slip. Inspect everything for damage
immediately upon delivery, and advise the carrier of
any shortages or damage. Any such claims should be
led with the carrier. The carrier, not the shipper, is
responsible for shortages and damage to the shipment
whether visible or concealed.
1.D Dimensions
See Figure 1 and Figure 2
1.E Locating the Appliance
The appliance should be located to provide
clearances on all sides for maintenance and inspection.
It should not be located in an area where leakage of
any connections will result in damage to the area
adjacent to the appliance or to lower oors of the
structure.
When such a location is not available, it is
recommended that a suitable drain pan, adequately
drained, be installed under the appliance.
The appliance is design certied by CSA-
International for installation on combustible ooring;
in basements; in closets, utility rooms or alcoves.
Brute Deluxe Boilers or Water Heaters must never
be installed on carpeting. The location for the
appliance should be chosen with regard to the vent
pipe lengths and external plumbing. The unit shall be
installed such that the gas ignition system components
are protected from water (dripping, spraying, rain, etc.)
during operation and service (circulator replacement,
control replacement, etc.). When vented vertically, the
Brute Deluxe must be located as close as practical to
M T 2 C
SERIES
M T 2
USAGE
H
V
SIZE
0 2 0 0
0 3 0 0
0 4 0 0
FUEL
N
P
FIRING
MODE
C
K
LOCATION
C
REVISION
2
3
HEAT
EXCHANGER
B
C
N
P
2
5
OPTIONS
CODE
X
L
PUMP
OPTIONS
X
N
S
G
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
B
B