Conversion Kit

ManualsBrandsBradford White ManualsCommercialElectriFLEX LD ® (LIGHT-DUTY) Upright Electric

LightDutyCommercialElectric

VoltageandWattageConversionInstructions

Conversion to be performed by a qualified service person only.

Underwriters Laboratories Inc. recognizes this procedure as herein presented and no

deviation from these instructions are allowed.

LDWH‐6U

LDWH‐12U

LDWH‐20L

LDWH‐30L



LE16WV

LE112WV

LE120WV



LD-6U

LD-12U

LD-12UT

LD-20U

LD-30U

LE16U

LE110U

LE112T

LE115U

LE120U

238‐46411‐00H9/21

LD-20L LE120L LE230LN

LD-30L LE130L LE240LN

LD-30R LE140L L E 250LN

LD-40L LE150L LE330S

LD-40S LE230S LE340S

LD-50L LE240S LE350S

LD-50S LE250S

LD-65R LE265T

LD-80R LE280T

LD-120R LE2120T

Summary of content (8 pages)

PAGE 1
Light Duty Commercial Electric Voltage and Wattage Conversion Instructions Conversion to be performed by a qualified service person only. Underwriters Laboratories Inc. recognizes this procedure as herein presented and no deviation from these instructions are allowed.
PAGE 2
The conversion procedure outlined in the instruction manual is to be executed only by Qualified Service Personnel. Read these instructions first before proceeding with the conversion. The purpose of this instruction manual is to instruct about the changing of wattage and voltage for Light Duty Commercial Electric Water Heaters manufactured by Bradford White Corporation. ETL recognizes this procedure as herein presented and no deviation from these instructions are allowed.
PAGE 3
Element(s) Removal: 1. Turn OFF electrical power to water heater, DISCONNECT FROM POWER SOURCE. Remove screw 2. Drain water heater. 3. Remove element access cover(s). Element access cover 4. Remove Insulation. Remove insulation 5. Remove thermostat(s) protector.
PAGE 4
6. Disconnect wire leads from element(s) terminal block. Element terminal block Disconnect wire leads from element terminal block 7. Remove element(s) from tank using 1½" deep well socket or wrench. Unscrew element(s) counter-clockwise to remove from tank. Unscrew element(s) counter‐clockwise to remove from tank Element(s) Installation: 1. Check element terminal block for proper electrical rating. Note: Some elements have a dual rating, so be sure to check all surfaces on element terminal block.
PAGE 5
2. Apply new gasket(s) to new element(s) from conversion kit. Note: Make sure gasket is seated flat against element flange without rolls or gaps. Gasket 3. Thread new element(s) clockwise into tank. Tighten element(s) with a 1 ½" deep well socket or wrench. Do not over tighten. Over-tightening may damage gasket. Note: Clean any debris from element(s) fitting to tank. Lubricate element(s) threads as needed with thread lubricant. Element flange 4. Be sure tank is filled with water and check for leaks. 5.
PAGE 6
NOTES Page 6 of 8
PAGE 7
NOTES Page 7 of 8
PAGE 8
United States General Contact 800-523-2931 Technical Support 800-334-3393 Email Warranty Email Service Parts Email techsupport@bradfordwhite.com 800-531-2111 warranty@bradfordwhite.com 800-538-2020 parts@bradfordwhite.com Canada General Contact 866-690-0961 Technical Support 800-334-3393 Email Warranty Email Orders techsupport@bradfordwhite.com 800-531-2111 warranty@bradfordwhite.com ca.orders@bradfordwhite.com International General Contact Orders international@bradfordwhite.com export.