POWER VENTED GAS WATER HEATER A Spanish language version of these instructions is available by contacting the company listed on the rating plate. La version espanola de estas instrucciones se puede obtener al escribirle a la fabrica cuyo nombre aparece en la placa de especificaciones. INSTALLATION AND OPERATING INSTRUCTION MANUAL WARNING: If the information in these instructions is not followed exactly, a fire or explosion may result causing property damage, personal injury, or death.
CONGRATULATIONS! You have just purchased one of the finest water heaters on the market today! This installation, operation and instruction manual will explain in detail the installation and maintenance of your new Power Vented Gas Water Heater. We strongly recommend that you contact a plumbing professional for the installation of this water heater. We require that you carefully read this manual, as well as the enclosed warranty, and refer to it when questions arise.
TABLE OF CONTENTS GENERAL INFORMATION................................................................. INSTALLATION. ................................................................................. Locating The Water Heater ......................................................... Minimum Clearances .................................................................. Venting ......................................................................................... Specifications for 48 Gal (181.
GENERAL INFORMATION This gas-fired water heater’s design is certified by CSA International under the American National Standard Z21.10.1 and CSA 4.1-M, most current editions at the time of manufacture. This water heater must be installed in accordance with local codes or, in the absence of local codes, the National Fuel Gas Code, ANSI Z223.1-Latest Edition) and/or in Canada CAN/CGA B149 Installation Codes (Latest Editions).
General Information continued- A sacrificial anode is used to extend tank life. The removal of this anode, for any reason, will nullify the warranty. In areas where water is unusually active, an odor may occur at the hot water faucet due to a reaction between the sacrificial anode and the impurities in the water. If this should happen, an alternative anode may be purchased from the supplier that installed this water heater. This will minimize the odor while protecting the tank.
Installation (Locating The Water Heater) continued- Water heater corrosion and component failure can be caused by the heating and breakdown of airborne chemical vapors. Examples of some typical compounds that are potentially corrosive are: spray can propellants, cleaning solvents, refrigerator and air conditioning refrigerants, swimming pool chemicals, calcium and sodium chloride, waxes and process chemicals.
Installation (Locating The Water Heater) continued- WARNING DO NOT ATTEMPT TO LIGHT ANY GAS APPLIANCE IF YOU ARE NOT CERTAIN OF THE FOLLOWING: Liquefied petroleum gases/propane gas and natural gas have an odorant added by the gas supplier that aids in the detection of the gas. Most people recognize this odor as a “sulfur” or “rotten egg” smell. Other conditions, such as “odorant fade” can cause the odorant to diminish in intensity, or “fade”, and not be as readily detectable.
Minimum Clearances WARNING Failure to adhere to these installation and operating instructions may create a hazard to life and property and will nullify the warranty. This installation must allow access to the front of the water heater and adequate clearance must be provided for servicing and operating this water heater. The water heater may be installed on either a combustible or noncombustible floor.
Venting continued- A= B= C= E= 12 inches (30 cm) 12 inches (30 cm) *b 12 inches (30 cm) 4 feet (1.
Venting continued- Vent pipes serving power vented appliances are classified by building codes as “vent connectors”. Required clearances from combustible materials must be provided in accordance with information in this manual under LOCATION OF WATER HEATER and CLEARANCES, and with National Fuel Gas Code and local codes. All vent pipes and terminals are to have a 1” minimum clearance to combustibles.
Venting continued- NOTICE For installations in Canada, field supplied vent piping must comply with CAN/CGA B149.1 (latest edition) and be certified to the Standard For Type BH, Class II, 65°C, Gas Venting Systems, ULC S636. Components of this listed system shall not be interchanged with other vent systems or unlisted pipe/fittings.
Venting System Condensation Condensate formation does not occur in all installations of power vented water heaters, but should be protected against on installations where condensation can form in the venting system.
Venting (Part I) continued- sure the vent pipe terminal elbow fitting is at least 1” (2.5 cm) away from the edge of the wall. TABLE 1 - VENT CONNECTOR LENGTHS FOR 3” (7.6 cm) DIAMETER VENT PIPE Terminating # of Elbows Maximum straight Length ft (m) 48, 65 gal. Through the Wall Through the Wall Through the Wall Through the Wall Through the Roof Through the Roof Through the Roof Through the Roof 1 2 3 4 0 1 2 3 55 (16.8) 50 (15.2) 45 (13.7) 40 (12.2) 60 (18.3) 55 (16.8) 50 (15.2) 45 (13.
Venting (Part I) continued- 3” (7.6 cm) 90 vent terminal supplied. Two 45 elbows are equivalent to one 90 elbow. CONNECTION TO 3” (7.6 CM) VENT PIPE CONNECTION TO A 3” (7.6 CM) TO 4” (10.2 CM) REDUCER Figure 2 IMPORTANT All of the Venting connections must be leak checked with a soap and water solution upon initial start up of the water heater. Any leaks must be repaired before continuing operation of the water heater. THROUGH THE WALL VENTING: (HORIZONTAL VENTING) Cut a 3 1/2 in. (8.
Venting (Part I) continued- 4” VENT INSTALLATION 3” VENT INSTALLATION Figure 3 15
Venting (Part I) continued- THROUGH THE ROOF VENTING: (VERTICAL VENTING) Cut the necessary holes through the roof and ceiling and install the vent connector as shown in Figure 4. Make sure that the installation meets the local codes and/or The National Fuel Gas Code ANSI Z223.1 (Latest Edition) or CGA/CAN B149 Installation Code (latest edition).
Venting (Part I) continued- THROUGH THE WALL VENTING WITH LOW GROUND CLEARANCE: When venting cannot exit through the wall at a height greater than or equal to 12” (30.5 cm) above the ground, or anticipated snow level, the installation must be modified as shown below (see Figure 5). Refer to Table 3 for maximum venting lengths using 3” (7.6 cm) vent pipe or Table 4 for maximum lengths using 4” (10.2 cm) vent pipe.
Venting (Part I) continued- TABLE 3 3” (7.6 cm) VENT CONNECTOR LENGTHS FROM INSIDE WALL FOR LOW GROUND CLEARANCE INSTALLATIONS Terminating # of Elbows Max Straight Length ft (m) 48,65 gal. (2) 90 Elbows with (1) 90 Elbow (2) 90 Elbows with (1) 90 Elbow (2) 90 Elbows with (1) 90 Elbow (2) 90 Elbows with (1) 90 Elbow 1 2 3 4 40 (12.2) 35 (10.7) 30 (9.1) 25 (7.6) Min straight Length ft (m) 5 (1.5) 5 (1.5) 5 (1.5) 5 (1.5) TABLE 4 4” (10.
Part II - Venting Specifications for: 40 Gallon (151.4 L) 50 Gallon (189.2 L) 60 Gallon (227.1 L) This water heater is a power vented appliance and is designed to vent its products of combustion through 2” (5.1 cm) or 3” (7.6 cm) diameter vent pipe to the outdoors. The water heater may be either vented horizontally through the wall or vertically through the roof. Use a 3” (7.6 cm) to 2” (5.1 cm) reducer to connect to the vent outlet when using 3” (7.6 cm) vent pipe. Apply proper cement at joint locations.
Venting (Part II) continued- TABLE 6 VENT CONNECTOR LENGTHS FOR 3” (7.6 cm) DIAMETER VENT PIPE Terminating Max straight Min straight # of 90 Elbows Length Length (excluding vent ft (m) ft (m) terminal) Through the Wall 1 115 (35) 10 (3.1) Through the Wall 2 110 (33.5) 10 (3.1) Through the Wall 3 105 (32.0) 10 (3.1) Through the Wall 4 100 (30.5) 10 (3.1) Through the Wall 5 95 (29.0) 10 (3.1) Through the Roof 0 120 (36.6) 15 (4.6) Through the Roof 1 115 (35) 15 (4.6) Through the Roof 2 110 (33.5) 15 (4.
Venting (Part II) continued- IMPORTANT All of the Venting connections must be leak checked with a soap and water solution upon initial start up of the water heater. Any leaks must be repaired before continuing operation of the water heater. THROUGH THE WALL VENTING: (HORIZONTAL VENTING) Cut a 2 1/2 in. (6.4 cm) diameter hole in the wall at the point where the vent connector is going to pass through the wall.
Venting (Part II) continued- THROUGH THE ROOF VENTING: (VERTICAL VENTING) Cut the necessary holes through the roof and ceiling and install the vent connector as shown in Figure 8. Make sure that the installation meets the local codes and/or The National Fuel Gas Code ANSI Z223.1 (Latest Edition) or CGA/CAN B149 Installation Codes (latest edition).
Venting (Part II) continued- THROUGH THE WALL VENTING WITH LOW GROUND CLEARANCE: When venting cannot exit through the wall at a height greater than or equal to 12” (30.5 cm) from the ground or from the anticipated snow level, then the installation must be modified as shown below (see Figure 9). Refer to Table 7 for maximum venting lengths using 2” (5.1 cm) vent pipe or Table 8 for maximum lengths using 3” (7.6 cm) vent pipe.
Venting (Part II) continued- TABLE 7 2” (5.1 cm) VENT PIPE LENGTHS FROM INSIDE WALL FOR LOW GROUND CLEARANCE INSTALLATIONS Terminating (2) 90 Elbows with Vent Terminal (2) 90 Elbows with Vent Terminal (2) 90 Elbows with Vent Terminal (2) 90 Elbows with Vent Terminal # of Elbows 1 2 3 4 Max straight Length ft (m) 30 (9.1) 25 (7.6) 20 (6.1) 15 (4.6) Min straight Length ft (m) 2 (.6) 2 (.6) 2 (.6) 2 (.6) TABLE 8 3” (7.
Vent Pipe Preparation and Joining Most failures in vent systems result from improper preparation and joining of pipe and fittings. The guidelines below must be followed when installing the venting system. If you have any question about the application or installation of the venting system, contact the vent pipe manufacturer, supplier, or your plumbing professional. 1) Specific cleaners, solvents, primers and cements are available for PVC, CPVC, and ABS pipe.
Vent Pipe Preparation and Joining continued- d) Cementing must be done quickly to avoid over-drying before joining. i) Apply one coat to the outside end of the pipe at a width slightly greater than the depth of the socket. ii) Apply a coat around the inside of the fitting socket. iii) Apply a second coat around the end of the pipe. 4) Joining a) Joints should be made immediately after cement is applied. b) After fully inserting pipe into fitting socket, hold joint together for about 15 to 20 seconds.
Combustion Air Supply WARNING Liquefied petroleum gases/propane gases are heavier than air and will remain at floor level if there is a leak. Basements, crawl spaces, closets and areas below ground level will serve as pockets for accumulation of leaking gas. Before lighting, smell all around the appliance area for gas. Be sure to smell next to the floor. IF YOU SMELL GAS: Do not try to light any appliance. Do not touch any electric switch; do not use any telephone in your building.
Installation (Combustion Air Supply) continued- All Air From Inside the Building: The confined space must be provided with two permanent openings communicating directly with an additional room(s) of sufficient volume so that the combined volume of all spaces meets the criteria for an unconfined space. The total input of all gas utilization equipment installed in the combined space must be considered in making this determination. Each opening must have a minimum free area of 1 square inch per 1000 BTU (6.
Water Connections NOTE: BEFORE PROCEEDING WITH THE INSTALLATION, CLOSE THE MAIN WATER SUPPLY VALVE. After shutting off the main water supply, open a faucet to relieve the water line pressure to prevent any water from leaking out of the pipes while making the water connections to the water heater. After the pressure has been relieved, close the faucet. The COLD water inlet and HOT water outlet are identified on the top of the water heater.
Water Connections continued- WARNING For protection against excessive temperatures and pressure, install temperature and pressure protective equipment required by local codes, but not less than a combination temperature and pressure relief valve certified by a nationally recognized testing laboratory that maintains periodic inspection of production of listed equipment or materials as meeting the requirements of the Standard for Relief Valves and Automatic Gas Shutoff Devices for Hot Water Supply Systems, A
Water Connections continued- WARNING Hydrogen gas can be produced in an operating water heater that has not had water drawn from the tank for a long period of time (generally two weeks or more). Hydrogen gas is extremely flammable. To prevent the possibility of injury under these conditions, we recommend the hot water faucet to be open for several minutes at the kitchen sink before you use any electrical appliance which is connected to the hot water system.
Gas Connections The gas supply lines must meet all requirements of the National Fuel Gas Code (ANSI Z223.1-Latest Edition), or in Canada CAN/CGA B149.1 Natural Gas Installation Code (Latest Edition) or CAN/CGA B149.2 Propane Installation Code (Latest Edition). The minimum permissible gas supply pressure for the purpose of input adjustment is one (1.0) inch (0.25 kPa) water column above the operating manifold pressure. See the rating plate and gas valve for the manifold pressure and gas type.
Electrical Connections All electrical wiring and connections must be in accordance with the National Electric Code ANSI/NFPA No. 70 (latest edition), or the Canadian Electrical Code C22.1 (latest edition) and any local codes which may apply. The water heater must be electrically grounded. If a flexible line cord and plug is permitted by local code, then provide a (3) three wire grounding type receptacle within 6 feet (1.9 m) of the water heater and use the flexible cord provided.
Wiring Diagram B C A Y Figure 10 34
GENERAL OPERATION WARNING Water heaters are heat producing appliances. To avoid damage or injury there must be no materials stored against the water heater or vent-air intake system, and proper care must be taken to avoid unnecessary contact (especially by children) with the water heater and vent-air intake system.
Lighting and Shutdown instructions FOR YOUR SAFETY READ BEFORE LIGHTING WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life. A. This appliance is equipped with an ignition device which automatically lights the pilot. Do not try to light the pilot by hand. If you cannot reach your gas supplier, call the fire department. C. Use only your hand to slide the gas control switch. Never use tools.
Thermostat Adjustment The thermostat dial is adjusted to its lowest setting when shipped from the factory. When adjusting the thermostat, it should be remembered that lower temperature settings are more energy efficient. To adjust the thermostat turn the dial clockwise until the minimum acceptable temperature is set. It is suggested that the starting point setting not exceed the 120°F (49°C) or “HOT” setting on the thermostat.
Burner Flame Check Cast Iron Burner: At the time of installation and at periodic intervals (not more than 6 months), a visual check of the main burner and pilot flames should be made to determine if they are burning properly. For ideal operation, the gas and air must be properly proportioned. The proper air-gas mixture is obtained by adjusting the air shutter on the mixer face of the main burner (See Figure 12).
MAINTENANCE WARNING Water heaters are heat producing appliances. To avoid damage or injury there must be no materials stored against the water heater or vent-air intake system, and proper care must be taken to avoid unnecessary contact (especially by children) with the water heater and vent-air intake system.
Maintenance continued- 5. Annually remove the inner door and main burner assembly to clean orifices and related parts of any dirt or other foreign material. Inspect the burner ports for obstructions or debris and clean with a wire brush as needed. Wire brush and/or vacuum clean the combustion chamber as needed to remove scale deposits and debris. NOTE: It is imperative for proper operation of the water heater that the inner door be replaced in the original location.
Maintenance continued- WARNING When lifting lever of the combination temperature and pressure relief valve, hot water will be released under pressure. Be careful that any released water does not result in bodily injury or property damage. 6. At least once a year, check the combination temperature and pressure relief valve to insure that the valve has not become encrusted with lime. Lift the lever at the top of the valve several times until the valve seats properly without leaking and operates freely.
Maintenance continued- CAUTION FOR YOUR SAFETY, DO NOT ATTEMPT REPAIR OF COMBINATION GAS CONTROL, BURNERS OR GAS PIPING. REFER REPAIRS TO A QUALIFIED SERVICE TECHNICIAN. Contact your supplier or plumbing professional for replacement parts or contact the company at the address given on the rating plate of the water heater. Provide the part name, model and serial numbers of the water heater when ordering parts.
TROUBLESHOOTING LED Status Control Status Probable Cause None (LED not on or flashing) Electrical power not present. Control power switch in “OFF” position. Supply voltage interuppted. One short flash every four seconds Stand-by mode, Thermostat is satisfied (no faults). Temperature demand is satisfied (no call for heat). Alternates bright and dim (Heartbeat) Thermostat calling for heat (no fault). Tank temperature below set point of thermostat.
Troubleshooting continuedLED Status Control Status Probable Cause Six flashes-three flashes, three second pause (Soft lockout) Pilot flame extinguished. System resets after 5 minutes. 1. Unstable pilot. 2. Pilot tube blocked or restricted. 3. Oxidation build up on pilot electrode. 4. Wire damage to pilot assembly or bad connection at gas valve. 5. Insufficient combustion air. Six flashes-four flashes, three second pause Undesired-false pilot flame sensed. System auto resets.
PARTS LIST DRAWING PARTS LIST PART NAME AND DESCRIPTION 1. Blower Assembly 13. Air Shutter (Cast Iron Only) 2. Temp. Switch 14. T&P Relief Valve Opening 3. Pressure Switch 15. Pilot Assembly 4. Flue Baffle 16. Cast Iron Burner 5. Honeywell Gas Control Valve 17. Main Burner Orifice 6. Drain Valve 18. Gas Feedline 7. Fiberglass Insulation (not shown) 19. Flammable Vapors Sensor 8. Foam Insulation (not shown) 20. Sensor Harness 9. Outer Door 21. Thermal Well 10. Steel Burner 22. Inner Door Assembly 11.
THE FOLLOWING INSTRUCTIONS ARE FOR INSTALLATION OF: GAS WATER HEATERS SUITABLE FOR WATER (POTABLE) HEATING AND SPACE HEATING 1. All piping components connected to this water heater for space heating applications must be suitable for use with potable water. In Massachusetts, space heating piping length must not exceed 50 feet. 2. Toxic chemicals, such as those used for boiler treatment, must not be introduced into potable water used for space heating. 3.
NOTES 47
NOTES 48