Spec Sheet
NATURAL GAS AND LIQUID PROPANE GAS
Power Direct Vent Energy Saver Models
Meet or exceed ASHRAE 90.1b (current standard) C.E.C. Listed
80% Recovery Efficiency
Model
Number
Approx.
Shipping
Weight lbs.
A
Floor to
Vent
Conn.
in.
B
Jacket
Dia.
in.
Capacity Recovery at
Degree °F Rise*
PDV-80T-300-3N(A)
PDV-100T-360-3N(A)
U.S.
Gal.
80
100
Imp.
Gal.
66
83
Nat. & LP
BTU/Hr.
Input
300,000
360,000
40°F
728
873
100°F
291
349
140°F
208
249
1
1
69
5
/
8
78
5
/
8
665
735
28
1
/
4
28
1
/
4
Model
Number
Approx.
Shipping
Weight kg.
A
Floor to
Vent
Conn.
mm.
B
Jacket
Dia.
mm.
Capacity Recovery at
LPH °C Rise*
PDV-80T-300-3N(A)
PDV-100T-360-3N(A)
Liters
303
379
Nat. & LP
kW
Input
87.9
105.5
56°C
1101
1321
60°C
787
942
4.4°C
2755
3304
1765
1892
Std.
Std.
ASME
ASME
F
Floor to
Heater
Top
in.
63
3
/
4
72
3
/
4
F
Floor to
Heater
Top
mm.
1622
1851
C
Floor to
Gas
Conn.
in.
13
5
/
8
13
5
/
8
C
Floor to
Gas
Conn.
mm.
356
356
D
Floor to
Hot
Water
Conn.
in.
51
3
/
8
60
3
/
8
D
Floor to
Hot
Water
Conn.
mm.
1308
1537
E
Floor to
Cold
Water
Conn.
in.
20
7
/
8
20
7
/
8
E
Floor to
Cold
Water
Conn.
mm.
527
527
302
333
740
815
336
370
718
718
G
Floor to
Top
Water
Conn.
in.
65
3
/
4
74
3
/
4
G
Floor to
Top
Water
Conn.
mm.
1670
1899
K
Depth
in.
44
5
/
8
44
5
/
8
K
Depth
mm.
1143
1143
Gas
Conn.
in.
3
/
4
3
/
4
Gas
Conn.
mm.
19
19
Relief
Valve
Open
in.
Relief
Valve
Open
mm.
25
25
Power Direct Vent Series Water Heater
Printed in U.S.A.
750-B-0214-A
©2014, Bradford White Corporation. All rights reserved.
Ambler, PA
For U.S. and Canada field service, contact your professional installer or local Bradford White sales representative.
Sales 800-523-2931
●
Fax 215-641-1670 / Technical Support 800-334-3393
●
Fax 269-795-1089
●
Warranty 800-531-2111
●
Fax 269-795-1089
International: Telephone 215-641-9400
●
Telefax 215-641-9750 / www.bradfordwhite.com
Sales / Technical Support 866-690-0961 / 905-238-0100
●
Fax 905-238-0105 / www.bradfordwhite.com
*Recoveries are based on Natural Gas input and 80% Thermal
Efficiency.
For Propane (LP) models change suffix “N” to “X”.
(A) = ASME Code Available
For 5 year models change suffix from “3” to “5”.
220V/50Hz Available - Consult factory.
For LowNOx compliance to meet SCAQMD requirements,
place an “E” following the BTU Input identifier of the
model number. Example: PDV-80T-300E-3N(A)
**Note: The standard vent kit (p/n 243-41769-01) shipped
with the heater, but in a separate carton includes: horizontal
vent terminal, an elbow, condensate tee, vent connector
clamps, and two 39" (990mm) straight sections of co-axial
vent pipe. Can be cut for installation. Optional vent kits are
available and will allow for extensions up to 21 feet. For
further details please reference the installation instructions.
For vertical venting please consult factory for optional vent
components.
D
G
A
C
E
F
B
K
5
3
/
16
"
Inside Dia.
7
7
/
8
"
Outside Dia.
Sample Specification
The water heater shall be a Bradford White model with a rated storage capacity of not less than_______gallons (_______liters), a minimum gas input of
_______BTUHr. (_______ kW), a minimum recovery of _______GPH (_______ LPH). The tank shall be Vitraglas
®
lined and have a bolted hand hole cleanout.
A digital LCD display shall be integrated into the front control box, and the control shall be an adjustable electronic thermostat to any temperature up to 185ºF
(85ºC), and must have an automatic re-set Energy Cut-off (E.C.O), which shuts off all gas in an event of a overheat condition. The tank shall have
_______magnesium anode rods installed in separate tank head couplings. The heater shall have Non-CFC foam insulation, electronic ignition, and come
equipped with an ASME rated T&P relief valve, a cold water inlet Hydrojet
®
Sediment Reduction System, and an induced draft blower motor for direct venting
(115V AC required). It shall be design certified by CSA International for 180ºF (82ºC) application, either with or without a separate storage tank, and comply
with state and local codes and ordinances.
General
All gas water heaters are certified at 300 PSI test pressure (2068 kPa) and 150 PSI working pressure (1034 kPa). All models are design certified by CSA
International (formerly AGA/CGA), ANSI standard Z-21.10.3, for up to 180°F (82°C) application as an Automatic Storage Heater, and an Automatic Circulating
Tank Heater. As an Automatic Storage Heater, all models are complete, self-contained water heating systems. It needs no separate storage tank, pump, wiring
or elaborate piping network. When equipped with a mixing valve, it will supply 180°F (82°C) sanitizing and lower temperature general purpose hot water
simultaneously. These models can be used either as a single unit or in multiples connected in series or parallel (recommended).
Dimensions and specifications subject to change without notice in accordance with our policy of continuous product improvement.