- Bradley Tech Plumbing Product User Manual

ManualsBrandsBradley Smoker ManualsPlumbing ProductAERADA 1000 Series S53-306

WARNING

Read this entire installation manual to ensure proper installation, then file

these instructions with the owner or maintenance department.

Flush all the water supply lines before making connections, then make

sure the water supply is turned off before beginning installation.

Do not use pipe dope on faucet and supply connections. Possible

solenoid contamination could occur and will void any warranty. Teflon

tape is the recommended sealant. Use plumber’s putty only to seal the

faucet to the deck.

The installation site should have access to an electrical box with 120 volt

AC, 60 Hz cycle for input to a transformer. When installing the transformer,

the electrical box should be located within six feet of the sink.

The DC faucets are powered by four “AA” factory-installed alkaline

batteries.

Product warranties may be found under “Product Information” on our web

site at www.bradleycorp.com.

Compliance and conformity to local codes and ordinances is the

responsibility of the installer.

Aerada 1000 Series

Gooseneck Faucet

Installation

Instructions

215-1559 Rev. A; EN 04-216A

Page 1 of 8 9/23/04

P.O. Box 309, Menomonee Falls, WI 53052-0309

Phone: 1-800-BRADLEY FAX: (262) 251-5817

http://www.bradleycorp.com

S53-306 DC Gooseneck with Centershank

S53-307 DC Gooseneck with 4" Trimplate

S53-308 AC Gooseneck with Centershank

S53-309 AC Gooseneck with 4" Trimplate

232-007 Plug-In Transformer for AC Gooseneck

Summary of content (8 pages)

PAGE 1
Installation Instructions Aerada 1000 Series Gooseneck Faucet S53-306 S53-307 S53-308 S53-309 232-007 DC Gooseneck with Centershank DC Gooseneck with 4" Trimplate AC Gooseneck with Centershank AC Gooseneck with 4" Trimplate Plug-In Transformer for AC Gooseneck WARNING Read this entire installation manual to ensure proper installation, then file these instructions with the owner or maintenance department.
PAGE 2
Aerada 1000 Series Gooseneck Faucet Installation Instructions Table of Contents Faucet Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Supplies Required for Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Installation Information Installing Single Hole and Cover Plate . . . . . . . . . . . . . . . . . . . . . . . . 3 Installing Solenoid Valves and Electronic Box (AC) . . . . . . . . . . . . . .
PAGE 3
Installation Instructions Aerada 1000 Series Gooseneck Faucet Installation Instructions - Single Hole and Cover Plate 1 Remove the locknut (1), washer (2), stilt washer (3) from the spout shank (4). Remove shank from cover plate (if supplied). Install faucet assembly into deck hole. Use plumbers putty to seal faucet to deck. 2 4 3 Be careful not to nick or cut the sensor cable during installation. 2 1 3 Install stilt washer (1) all the way up onto shank, crown side up.
PAGE 4
Aerada 1000 Series Gooseneck Faucet Installation Instructions Installation Instructions - Solenoid Valves and Electronic Box (AC) Models S53-308 and S53-309 1 Thread the union nut (1) of the solenoid assembly to the faucet shank (2). Use Teflon tape on the threads to ensure a leak-free joint. Make sure the solenoid is positioned for easy access. Tighten the union nut. 2 CAUTION: Do not use pipe dope on threads. The solenoid could become contaminated and will void any warranty.
PAGE 5
Installation Instructions Aerada 1000 Series Gooseneck Faucet Installation Instructions - Electronic Battery Box (DC) Models S53-306 and S53-307 1 Install the baseplate and mount the electronic box to the desired wall location. The baseplate must be mounted either level with or above solenoid valve, and within 12" of the solenoid valve. 2 Remove the strain relief cover and screw (1) using hex key provided (2) . Remove foam gasket (3). Separate the foam gasket at the perforation.
PAGE 6
Aerada 1000 Series Gooseneck Faucet Installation Instructions Faucet Operation Operating Modes • Normal Motion Detecting Mode: water flows within 1/4 second after activating sensor (i.e., putting hands in front of collar) and continues to stay on as long as motion is detected. Maximum time is 45 seconds (factory default setting). • Scrub Mode: water continues to flow for 60 seconds (default) after deactivating the sensor (removing hands).
PAGE 7
Installation Instructions Aerada 1000 Series Gooseneck Faucet Troubleshooting Whenever new batteries are installed, AC power is applied, or a manual reset button is pressed, the LED on the electronics cover will blink and an audible indicator chirps twice per second whenever hand presence is detected. After 8 minutes, the LED and buzzer function stops. If an error occurs, the LED will blink and the buzzer will sound every 30 seconds to assist in diagnosing the problem.
PAGE 8
Aerada 1000 Series Gooseneck Faucet Installation Instructions Troubleshooting continued . . . Problem Check Possible Solution Faucet works in reverse. Solenoid wiring on DIN connector (no beeps). Replace solenoid. Faucet turns off too soon. Faucet operating mode (no beeps) or faucet range setting. Change mode or range setting using DIPswitch (page 6). Faucet stays on longer than normal. Dirty solenoid valve (no beeps). Clean internal parts or replace solenoid valve. Clogged spout outlet.