Installation Sheet

800 Series
Mounting Kits and Anchoring Devices
© 2015 Bradley
P.O. Box 309, Menomonee Falls, WI 53052-0309
800 BRADLEY (800 272 3539) [phone]
bradleycorp.com
Page 1 of 2 11/9/2015
This information is subject to change without notice.
Bradley_GrabBar_800SeriesMountingKitsAndAnchoringDevices
Stud walls with wood sup ports
 899-010
MATERIAL INCLUDED
2 – ¼ x 2½" PLATED
STEEL HEX HEAD LAG BOLTS
Partition walls
 899-011
MATERIAL INCLUDED
A) 2 – ¼-20 x 1½"
PLATED STEEL HEX HEAD
MACHINE SCREWS
B) 2 CAP NUTS
C) 1 BACKING PLATE
Panel walls
 899-012
MATERIAL INCLUDED
A) 2 – ¼-20 x 3"
PLATED STEEL HEX
HEAD MACHINE
SCREWS
B) 2 TOGGLE NUTS
Masonry walls
 899-013
MATERIAL INCLUDED
A) 2 – ¼-20 x 1"
PLATED STEEL HEX HEAD
MACHINE SCREWS
B) 2 – ¼-20 LEAD ANCHORS
2½"
(64mm)
1"
(25mm)
Concealed Mounting Kits
Metal Stud Wall Mounting Kits
 899-014
(CONCEALED OR EXPOSED)
MATERIAL REQUIRED
A) IN-WALL ANCHOR PLATE
899-015 (NOT INCLUDED).
SPECIFY AND ORDER
SEPARATELY – SEE ANCHOR
PLATES IN NEXT COLUMN.
B) #10 sheet metal screws
(furnished by others)
C) METAL STUD
D) 2 – ¼-20 x 1¼"
FLAT HEAD machine SCREWS.*
E) WALL DIMENSIONS (TO BE FURNISHED
IF OVER ¾").
* INCLUDED WITH MOUNTING KIT 899-014.
A
C
B, D
E
Block Wall Mounting Kits
 899-016
(CONCEALED OR EXPOSED)
MATERIAL REQUIRED
A) FRONT ANCHOR PLATE 3" x 3" x
1
⁄8" COLD ROLLED
STEEL, GALVANIZED, CARBON STEEL – CENTER SLOT
PUNCHED AND 2 FASTENER HOLES PRE-PUNCHED.*
B) 2 – ¼-20 x 1¼" PLATED PHILLIPS FLAT HEAD SELF
TAPPING SCREWS.*
C) 1 –
3
⁄8-16 STEEL ZINC-PLATED TIE ROD WITH NUT.*
D) BACK ANCHOR PLATE 3" x 3" x
3
⁄16" COLD ROLLED
STEEL – TAPPED FOR AND INCLUDING
3
⁄8-16 STUD
AND NUT.*
E) FINISHED WALL THICKNESS (TO BE FURNISHED IF
OVER ¾").
F) MASONRY WALL (THICKNESS TO BE FURNISHED).
* INCLUDED WITH MOUNTING KIT 899-016.
D
F
E
C
A
B
FRONT AN CHOR PLATE BACK AN CHOR PLATE
 899-015
x LENGTH (TO 96")
MATERIAL
4" x
1
⁄8" GALVANIZED, CARBON
STEEL – LENGTH AS SPECIFIED
TO 96" NOTE: SEPARATELY
ORDER 899-014 MOUNTING
KITS AS REQUIRED.
INSTALLATION:
FASTEN TO STUDS BEFORE WALL APPLIED.
RECESS AS REQUIRED FOR FLUSH FINISH WALL APPLICATION.
TO ATTACH GRAB BAR, DRILL #2 (.221 DIAMETER)
HOLES THRU WALLBOARD AND ANCHOR PLATE.
ATTACH WITH ¼-20 x 1¼" PLATED PHILLIPS
OVAL HEAD ROLLOCK TAPPING SCREWS.
UNIVERSAL
ANCHOR PLATE
In-Wall Anchor Plates
Order one mounting kit per grab bar flange.