Specification Sheet

2922-2873, 2922-2874
Adjustable Motor, Sensor-Operated Warm Air Hand Dryer
© 2014 Bradley
P.O. Box 309, Menomonee Falls, WI 53052-0309
800 BRADLEY (800 272 3539) [phone]
bradleycorp.com
Orders composed of products indicated as Bradex
®
will be available to ship in three days after receipt of
order at the factory. There is no pricing penalty for
this service from Bradley.
Page 1 of 2 5/29/2014
This information is subject to change without notice.
Bradley_HandDryer_2922-2873_2874
Standard Model 2922-287300 (aluminum - white)
Brad
ex
®
Standard Model 2922-287400 (stainless steel-satin
finish) Brad
ex
®
Product Materials
2922-2873 COVER: die-cast aluminum finished with white epoxy paint with
Steritouch
®
2922-2874 COVER: one-piece stainless steel; satin finish
Cover fixed to the base plate with tamper proof screws.
ADJUSTABLE MOTOR: motor is a thermally-protected universal type operating
at 23,400 RPM. Adjustable motor control switch has three settings; HI, MED and
LOW.
HEATING ELEMENT: 400 watt heating element constructed of nichrome wire and
protected by an automatic resetting thermal cutoff. Heater can be turned ON or OFF
via internal switch.
SENSOR OPERATION: Automatic infrared sensor with a 3 second run-on time
and a 30 second vandal shut-off.
BASE PLATE: Aluminum with four mounting holes and a .88" knockout.
Installation
Verify all rough-in dimensions prior to installation. Hand dryers require
a dedicated 15 amp circuit and must be properly grounded. GFI Circuit
protection is recommended. One side of dryer should be mounted to a stud.
For proper mounting heights, see installation manual.
Operation
Place hands 3"–6" below nozzle to activate air flow. Dryer will
stop after hands are removed from air flow.
Recommended for very high traffic areas.
®
Guide Specification
Surface-mounted hand dryer shall have a white cast aluminum cover with epoxy
paint (2922-2873) or stainless steel cover with satin finish (2922-2874). All
internal air flow paths shall incorporate SteriTouch antimicrobial technology. Hand
dryer shall include aluminum base plate, adjustable universal type motor and
infrared sensor. Dryer shall operate at 73 - 85 dB while delivering 78-100 CFM air
at a velocity of 250 - 265 MPH or 22,000 - 23,320 LFM. Dryer shall produce air at
110 - 140°F. Dryer shall have total power of 400 - 1200 watts with a consumption
of 3.3 - 10.0 A.
Overall dimensions: 12.5"H x 9.3"W x 7.6"D (319mm x 236mm x
192mm).
Weight: Aluminum - 11.6 lb (5.2 kg)
Stainless Steel - 14.2 lb (6.4 kg)
Product Specifications
Voltage: 100–120 V Consumption: 3.3–10.0 A
Nominal power: 400–1200 W RPM: 23,400
Airflow: 78–100 CFM Heating element: 400 W
Noise level: 73–85 dB Airspeed: 250–265 MPH
Frequency: 60 Hz Insulation: Grounding required
Temperature: 110ºF–140ºF (43ºC–60ºC) Certificates: UL 499 / CSA C22.2 (No. 36-08)
Drying time: 10–12 seconds Mounting:
Surface; not ADA compliant
With recess kit*; ADA compliant
Protection level: IP24
*Recess kit sold separately
Description Part Number
Recess Kit P10-749