Specification Sheet

S53-328, S53-329
Aerada
™
1100 Series High Arc Faucets with Infrared Control
© 2016 Bradley
P.O. Box 309, Menomonee Falls, WI 53052-0309
800 BRADLEY (800 272 3539) [phone]
bradleycorp.com
Verify all rough-in dimensions prior to installation.
Consult local and national codes. Conformity and compliance to
local and national codes is the responsibility of the installer.
Page 1 of 2 03/28/2016
This information is subject to change without notice.
Bradley_Faucets_S53-328_329
• ADA Compliant External Temperature Control
• Reliable Infrared Activation
• Adjustable Operating Modes
• Vandal Resistant Cast Brass Spout
• Chrome-Plated Finish
• Above-Deck Water-Tight Electronics
• 6V Lithium Battery Operation (Battery Included)
• 12V AC Transformer Available (Not Included)
Standard Equipment
Infrared Sensor
The IR Sensor uses a twin-beam system to respond quickly when needed, and to
eliminate false activations. The electronics can be adjusted between static mode
sensing the complete IR beam and dynamic mode sensing only hand motion.
Valve
The electronically activated solenoid valve provides reliable performance since
there are few moving parts and its operation is unaffected by most chemicals and
minerals found in municipal water supplies. The faucet includes (2) stainless
steel supply hoses with check stops to prevent backflow into the supply lines.
Flow Control/Rate
Operating range 20–80 PSI. The vandal-resistant aerator produces a .5 GPM
flow rate.
Faucet Body
Chrome-plated solid cast brass body. Centershank mounting with optional 4"
centerset trim plate available.
Sanitary
No-touch operation reduces water/soap splatter and addresses the public's
increasing awareness and concern about communicable diseases.
Vandal Resistant
The sensor module, circuit board and solenoid valve are enclosed in the solid
cast brass faucet body. The faucet also features a vandal-resistant aerator.
Code Compliance and Certifications
CSA
The 1100 Series High Arc Faucets are certified to meet CSA B125 test standards
for plumbing fixtures. The faucets are CSA approved in Canada and the United
States.
ASME A112.18.1
The 1100 Series High Arc Faucets are certified to meet the ASME A112.18.1
standard for plumbing fixtures.
ADA Compliance
The infrared sensor produces a broad detection zone that allows disabled users
to easily activate the faucet from either a front or side approach; the external
temperature control does not require tight grasping or rotating and turns on less
than 5 pounds of pressure, meeting ADA guidelines provided by ANSI A117-1.
Check Your Surroundings
Certain factors, such as intense direct sunlight, other infrared devices, or other
site conditions may interfere with the activation of infrared faucets. Contact your
Bradley Representative to discuss any application concerns.
Sample Specification
No-touch infrared faucet shall be (S53-329) Bradley Aerada
™
1100 Series
High Arc IR Faucet. The faucet shall be powered by a 6-volt DC lithium battery
(included). All Electronics shall be above deck within watertight enclosure. The
external temperature control shall be constructed of solid cast brass and shall
comply with ADA guidelines. The faucet shall include a chrome-plated, forged
brass body with centershank mounting, .5 GPM vandal-resistant aerator and
(2) stainless steel flexible supply hoses. The faucet shall be UPC approved and
certified to CSA standards.
Models
Faucet Only:
 S53-328 AC High Arc IR Faucet Centershank
 S53-329 DC High Arc IR Faucet Centershank
Optional Selections
Trim Plate:
 150-221 4" Chrome-plated trim plate
Transformer:
(options only used with S53-328 AC faucet, cannot be used on S53-329 DC Faucet)
 232-008 Plug-in Transformer 12V
 232-009 Hardwire Transformer 12V (1–8 Faucets)
Flow Control:
 269-1922 2.2 GPM Laminar Flow Control
(The 2.2 GPM flow control does not
meet California Energy Commission 20 CCR T.20, Div. 2, 1601-1609.)
Drain Assembly:
 269-1839 D-ASSY, Drain, Strainer, and Tailpiece
C US
Certified to
NSF/ANSI 372
Standard product selections contained within this document are third
party CERTIFIED to NSF/ANSI 372 meeting the Lead-Free content
requirement. Any product configured with custom options will be
COMPLIANT with NSF/ANSI 372 meeting the Lead-Free content
requirement.