Installation manual

ManualsBrandsBradley ManualsHome building and DecorSS-3

P.O. Box 309, Menomonee Falls, WI USA 53052-0309

PHONE 800.BRADLEY (800.272.3539) FAX 262.251.5817

bradleycorp.com

Installation

215-1493 Rev. G; ECM 11-08-011

Page 1 of 15 10/24/11

SS-3N/IR/STD

SS-3N/IR-WH

Express

Lavatory System SS-Series

Table of Contents

Pre-Installation Information .........................2

Components .......................................3

Supplies Required .................................4

Dimensions..................................... 4–5

Rough-Ins .........................................6

Installation .................................... 7–10

Sensor Assembly and Solenoid Valve Access ........11

Solenoid Valve Troubleshooting .....................12

Navigator

Mixing Valve Troubleshooting ............13

Stop Valve Troubleshooting ........................14

Cleaning and Maintenance for Terreon

.............14

Soap Dispenser Maintenance ......................15

Express Lavatory Systems are ADA and TAS compliant

U.S. Pat. Nos. 5,611,093, 5,369,818, D398,969

Other Patents Pending

SS-3N/IR/STD/LSD-3

SS-3N/IR-WH/LSD-3

Summary of content (15 pages)

PAGE 1
Installation SS-3N/IR/STD/LSD-3 SS-3N/IR/STD SS-3N/IR-WH Express® Lavatory System SS-Series Express Lavatory Systems are ADA and TAS compliant U.S. Pat. Nos. 5,611,093, 5,369,818, D398,969 Other Patents Pending SS-3N/IR-WH/LSD-3 Table of Contents Pre-Installation Information . . . . . . . . . . . . . . . . . . . . . . . . . 2 Components. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Supplies Required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 2
SS-3N/IR/STD, SS-3N/IR/WH Installation IMPORTANT! Read this entire installation manual to ensure proper installation. When finished with the installation, file this manual with the owner or maintenance department. Compliance and conformity to local codes and ordinances is the responsibility of the installer. Installation Packing List IS TH SIDE UP • • • • Separate parts from packaging and make sure all parts are accounted for before discarding any packaging material.
PAGE 3
Installation SS-3N/IR/STD, SS-3N/IR/WH Components SPRAYHEAD COVER (PART NUMBER VARIES WITH COLOR OF UNIT. CONTACT YOUR LOCAL BRADLEY REP. FOR ASSISTANCE). BOLT 5/16-18 160-371 SCREW 10-24 160-386 SPRAYHEAD BODY (PART NUMBER VARIES WITH COLOR OF UNIT. CONTACT YOUR LOCAL BRADLEY REP. FOR ASSISTANCE). BOWL (PART NUMBER VARIES WITH COLOR OF UNIT. CONTACT YOUR LOCAL BRADLEY REP. FOR ASSISTANCE).
PAGE 4
SS-3N/IR/STD, SS-3N/IR/WH Installation Supplies Required: • (8) ³⁄₈" wall anchors, bolts and 1" min. O.D. washers to mount main frame and bowl to wall (minimum pull-out rating of 1,000 lbs.) • STD. HEIGHT ONLY: (2) ³⁄₈" wall anchors, bolts and 1" min. O.D.
PAGE 5
Installation SS-3N/IR/STD, SS-3N/IR/WH Dimensions - Side Views 211⁄8" (537mm) 11½" (292mm) Standard Height 211⁄8" (537mm) Wall Hung Mounted at Standard Height 38½" (978mm) 11½" (292mm) 38½" (978mm) 34" (864mm) 34" (864mm) 85⁄8" (219mm) 30" (762mm) 30" (762mm) 3" (76mm) 13¼" (311mm) 85⁄8" (219mm) 13¼" (311mm) Scuff Base on Standard Height Only 211⁄8" (537mm) 11½" (292mm) Wall Hung Mounted at Juvenile Height Ages: 6 through 12 35½" (902mm) 31" (787mm) 27" (686mm) 85⁄8" (219mm) 10¼" (260mm
PAGE 6
SS-3N/IR/STD, SS-3N/IR/WH 1 Installation Rough-Ins C L 38-1/2" (978mm) 38-1/2" (978mm) 24-3/8" (619mm) 24-3/8" (619mm) 13" (330mm) 8" (203mm) 4" (102mm) A, F 2-3/4" 70mm) B H G B A, F B J D1 D2 34" (864mm) E 32" (813mm) B 28-3/4" (720mm) 15" (381mm) B B 24" (610mm) RIM HEIGHT SEE CHART BELOW 23" (584mm) 5-5/8" (143mm) 18" (457mm) C C FLOOR 27-1/2" (699mm) 3-1/2 (89mm) CODE 6 DESCRIPTION QTY. A ³⁄₈" Wall Anchors with a minimum pull-out force of 1,000 lbs.
PAGE 7
Installation 2 SS-3N/IR/STD, SS-3N/IR/WH Mount Frame to Wall Anchoring the frame to a wall that is not flat may cause the frame to bend, making it difficult to reinstall the access panels. If necessary, use shims to compensate for wall distortion. A Using a T20 torx key, remove the fasteners securing the access panel to the main frame, and remove the panel.
PAGE 8
SS-3N/IR/STD, SS-3N/IR/WH 4a Installation Connect the Supply — Hot and Cold Supply C A 4b The letter “H” on the Navigator Mixing Valve indicates hot water supply inlet. Connect one end of each hose to the Navigator valve (one on the hot side, one on the cold side). Connect the other swivel end to the stop valves. Loosen but do not remove the two mounting screws holding the valve bracket to the frame. Slide the valve bracket up and lift it from the frame.
PAGE 9
Installation 5 SS-3N/IR/STD, SS-3N/IR/WH Install the Drains To Drain Stub-Out 6 240/208 or 277 voltage is required for hot water heater. Refer to the installation manual provided with the hot water heater for further installation information. Optional Electric Tankless Water Heater A B Hang the water heater on the right side frame member. Connect the ½" flexible hose from the cold water supply stub-out to the hot water heater inlet. Bradley Corporation • 215-1493 Rev.
PAGE 10
SS-3N/IR/STD, SS-3N/IR/WH 7 Installation Connect Electrical and Sprayhead Supplies WARNING: The Express® control must be connected with the 24 VAC Class II transformer provided. Connections to 110 VAC can cause personal injury and will result in damage to the electronics. Connection of leads other than shown may cause permanent damage to the sensor.
PAGE 11
Installation SS-3N/IR/STD, SS-3N/IR/WH Sensor assembly and solenoid valve access • To access sensors: Remove the Phillips-head screws located in the bottom of the sprayhead body and lift the Terreon cover/shelf off. • To reinstall sprayhead cover/shelf: Position the cover/shelf on the sprayhead body and secure it to the sprayhead body using the screws provided.
PAGE 12
SS-3N/IR/STD, SS-3N/IR/WH Installation Troubleshooting – Solenoid Valve: Part nos. S07-067 (closed body) & S07-067A (thru body) Turn off water supplies to the unit before troubleshooting. 8 Item Qty. Part No.
PAGE 13
Installation SS-3N/IR/STD, SS-3N/IR/WH Thermostatic Mixing Valve Troubleshooting Before attempting to troubleshoot the valve or disassemble the components, check for the following conditions: • If stop valves are used, make sure that they are fully open. • Make sure that the hot and cold inlet pipes are connected properly, and that there are no cross-connections or leaking stop valves. • Check the hot water heater output to make sure that it is at least 10° F above the set temperature.
PAGE 14
SS-3N/IR/STD, SS-3N/IR/WH Installation Stop Valve Troubleshooting Problem Cause Solution Water dribbles or does not flow from the sprayhead. Stop Valves may not be functioning properly. 1. Close the stops and inspect the valves that supply water to the lavatory system. 2. Inspect the stop valves to see that they have been properly installed. Sprayhead delivers Stop Valves may ONLY hot OR cold water. not be functioning properly. 1.
PAGE 15
Installation SS-3N/IR/STD, SS-3N/IR/WH Fill Soap Dispenser The soap valve will dispense vegetable/coconut oil liquid soaps, synthetic detergents, viscous lotion soaps, and antiseptic solutions. A 10-15% concentration is recommended for vegetable or coconut oil liquid soaps. Before filling, rinse out each soap tank with hot water to remove packing dust. Shake water out thoroughly and allow to dry. DO NOT OVERFILL! Leaf Spring will engage when soap tank is pushed into place.