Installation manual

ManualsBrandsBradley ManualsLawn and GardenTDB3108

P.O. Box 309, Menomonee Falls, WI 53052-0309

Phone: 1.800.BRADLEY Fax: 262.253.4161

bradleycorp.com

215-1577 Rev. B; ECN 13-00-001

Page 1 of 19 4/3/2013

TDB3108 with

TouchTime

Control

TDB3108 Juvenile Height with

TouchTime

Control

TDB3108

Terreon

54" Circular Deep Bowl

Washfountain with TouchTime

Control

WF3208

Terreon

Extra Height 54" Circular

Classic Washfountain with 9"

Deep Bowl and TouchTime

Control

Table of Contents

Pre-Installation Information ....................................... 2

Circular Washfountain Dimensions ....................... 3–4

Rough-In Information ................................................. 5

Installing the Drain ..................................................... 5

Bowl/Pedestal Mounting and Assembly ..................... 6

Installing Drain Spud in Bowl ..................................... 7

TouchTime

Assembly ......................................... 8–11

Valve and Tubing Connections ................................. 12

Electrical Connections ............................................. 13

Water Supply and Adjust Temperature ..................... 13

Cleaning and Maintenance ................................ 14–15

Soap Valve Parts List ............................................... 16

Sprayhead Parts List and Troubleshooting ............... 17

Valve Assemblies ..................................................... 18

Vernatherm Parts List and Troubleshooting ............. 19

Installation

TDB3108 TAS Height with

TouchTime

Control

WF3208 with

TouchTime

Control

Summary of content (19 pages)

PAGE 1
Installation TDB3108 with TouchTime® Control TDB3108 Juvenile Height with TouchTime® Control TDB3108 TAS Height with TouchTime® Control WF3208 with TouchTime® Control 215-1577 Rev. B; ECN 13-00-001 © 2013 Bradley Page 1 of 19 4/3/2013 TDB3108 Terreon® 54" Circular Deep Bowl Washfountain with TouchTime® Control WF3208 Terreon® Extra Height 54" Circular Classic Washfountain with 9" Deep Bowl and TouchTime® Control Table of Contents Pre-Installation Information........................................
PAGE 2
TDB3108, WF3208 Installation IMPORTANT! Read this entire installation manual to ensure proper installation. When finished with the installation, file this manual with the owner or maintenance department. Installation Packing List IS TH SIDE UP • • • • Separate parts from packaging and make sure all parts are accounted for before discarding any packaging material. If any parts are missing, do not begin installation until you obtain the missing parts.
PAGE 3
TDB3108, WF3208 Installation Circular Washfountain Dimensions Model TDB3108 Model TDB3108 54" Circular - side view 54" Circular with optional accessories - side view Adjust to Towel Dispenser Mounting Holes 54" (1372) 6" (152) 47-1/4" (1200) 43-3/4" (1111) 34" (864) 63-5/8" (1616) w/ soap 55-1/8" (1400) w/o soap 10" (254) 23-1/2" (597) 47-1/4" (1200) 34" (864) 55-3/4" (1416) 19-1/2" (495) 43-3/4" (1111) 10" (254) 23-1/2" (597) 36" (914) 19-1/2" (495) Model TDB3108 is ADA Compliant 36" (91
PAGE 4
TDB3108, WF3208 Installation Circular Washfountain Dimensions Model TDB3208 Model TDB3208 54" Circular - side view 54" Circular with optional accessories - side view 54" (1372) Adjust to Towel Dispenser Mounting Holes 6" (152) 47-1/4" (1200) 63-5/8" (1616) w/ soap 55-1/8" (1400) w/o soap 43-3/4" (1111) 10" (254) 34" (864) 23-1/2" (597) 47-1/4" (1200) 55-3/4" (1416) 19-1/2" (495) 37-1/2" (953) Model TDB3208 is not ADA Compliant 34" (864) 43-3/4" (1111) 10" (254) 23-1/2" (597) 19-1/2" (495) 37-
PAGE 5
TDB3108, WF3208 Installation Rough-In Dimensions for Supplies and Drain (mm) Supplies from Above Supplies from Below or Through Wall Type B Type A Centrally rising vent with supplies from above (P-Trap furnished with unit.) Off-line vent with supplies from below (P-Trap supplied by Installer.) Type H Type O Centrally rising vent with supplies from below (P-Trap furnished with unit.) Top View Off-line vent with supplies from above (P-Trap supplied by Installer.
PAGE 6
TDB3108, WF3208 2 Installation Bowl/Pedestal Mounting and Assembly A Position the pedestal making sure the floor mounting holes (4 places) line up as shown. Mark the mounting hole positions on floor. Secure pedestal to floor with suitable fasteners, 1/2" anchors and bolts (supplied by installer). Do not overtighten. Bowl surface is smooth and possibly slippery. Approximate weight is 190 lbs. Handle with care! Threaded Rod Holes (4) TAS OPTION: Place TAS spacer on floor over the mounting holes.
PAGE 7
TDB3108, WF3208 Installation 3 Install Drain Spud in Bowl A Loosely attach the drain spud to the bowl with the locknut and washer. B TRAP OPTION: attach B trap to drain spud. Seal between drain spud and drain hole with plumber’s putty (supplied by installer). Strainer (S45-067) Spud (112-015) Drain Pre-Pack (S45-273) Tie Pipe OPTION: attach tie pipe bracket to drain spud. B Tighten the spud and lock nut against the bowl. Bowl C Secure the strainer to drain spud with the screws provided.
PAGE 8
TDB3108, WF3208 4a Installation Assemble TouchTime® – A and O Units without Tie Pipe Option (A Shown) A B C D Install hemmed end (not sharp end) of support tube with gasket onto bowl. Connect 1/2" supply tubing to sprayhead with 3/8" NPT to 1/2" tube connector and place sprayhead onto support tube. Run the tubing down through the support tube and connect to valve tube connector.
PAGE 9
TDB3108, WF3208 Installation 4a Assemble TouchTime® – A and O Units without Tie Pipe Option (A Shown) E Place the TouchTime module assembly on top of sprayhead. Rotate until actuator module locks in with tie bar. Drop TouchTime module wires down to the valve assembly. Skip to step G for units without soap. F For units with soap option, install the spacer, soap dispenser and cover using the third tie rod (8-5/8" long) and second coupling nut as shown. Secure with acorn nut and set screw.
PAGE 10
TDB3108, WF3208 4b Installation Assemble TouchTime® – B and H Units without Tie Pipe Option (B Shown) A Install hemmed end (not sharp end) of support tube with gasket onto bowl. B Connect 1/2" supply tubing to sprayhead with 3/8" NPT to 1/2" tube connector and place sprayhead onto support tube. Run the tubing down through the support tube and connect to valve tube connector. C Insert the 1-1/2" vent pipe (supplied by installer) down through the support tube and thread into vented trap.
PAGE 11
TDB3108, WF3208 Installation 4b D Assemble TouchTime® – B and H Units without Tie Pipe Option (B Shown) Place the TouchTime module assembly on top of the sprayhead. Drop TouchTime module wires down to the valve assembly. Unit with "H" Drain and TouchTime Module Shown, Also Available with "B" Drain Top Cover Skip to step F for units without soap. Soap Dispenser E For units with soap option, slide the spacer and soap dispenser over the 1-1/2" pipe.
PAGE 12
TDB3108, WF3208 5 Installation Connect Valve and Tubing for TouchTime Control Flush supply lines before making connections. A Connect 1/2" dia. tubing from the sprayhead to the solenoid assembly. The male connector for the valve assembly will remain tight and leakproof when tubing is cut and installed properly. Follow the procedures below when installing tubing to ensure that you achieve a leakproof seal. • Using a sharp razor, cut tubing squarely and remove any burrs.
PAGE 13
TDB3108, WF3208 Installation 6 Make Electrical Connections for TouchTime Control A Mount the terminal block in a convenient location using the hook and loop fastener supplied. Make sure all wires will reach. B Connect the two transformer wires, the two wires from each solenoid valve and the four wires from each TouchTime switch to the terminal block as shown. Plug the 24 VAC Class II transformer (S83-134) into a 110 VAC GFI outlet.
PAGE 14
TDB3108, WF3208 Installation Soap Maintenance Tips Soap Recommendations Quality soap dispensers require good quality soap and periodic maintenance to properly operate. Bradley soap dispensers will provide dependable, consistent operation over the long term when soap with reasonable viscosity and pH levels are used and when a minimal amount of periodic maintenance is performed on the valves. Soap thickness is determined by a measurement called viscosity.
PAGE 15
TDB3108, WF3208 Installation Cleaning/Maintenance Instructions for Terreon® Material Description: Terreon® is a NAHB Certified densified solid surface material composed of polyester resin and is resistant to chemicals, stains, burns and impact. Surface damage can be easily repaired with everyday cleansers or fine grit abrasives. Routine Cleaning: Clean daily or as often as conditions require using a standard commercial or household cleaner such as Formula 409® or Windex®.
PAGE 16
TDB3108, WF3208 Installation Parts List - Soap Valves (S09-007S, S09-057S, S09-010A) Soap Valve - Liquid Parts List Item Part No. Description 1 118-025 Valve Body 1 2 110-007 Packing Nut 1 3 135-001L Spring 1 4 125-001BU Washer 1 5 119-028 Plunger 1 * 161-014 Nut 1 * 124-001BV Washer 2 * 142-002AH Washer - Stainless Steel 1 1 5 Attaching Parts S09-007S Qty 34 35 24 2 1 * Not Illustrated This valve delivers a measured amount of soap with each upward stroke.
PAGE 17
TDB3108, WF3208 Installation Troubleshooting Sprayheads (Standard with Neoprene Spray Ring Grommet) 4 Repair kit does not include sprayhead grommet. Order as a separate item. 3 5 Sprayheads Parts List Item Part No.
PAGE 18
TDB3108, WF3208 Installation Parts List - Solenoid Valve (S27-250) Item Part No. Description 1 269-626 Male Connector 2 269-1246 Reducing Coupling 3 S27-250 Solenoid Valve Assembly 4 269-1346 Diaphragm* 5 269-577 Armature* 6 269-578 Spring* 6 3 5 4 * Repair Kit S65-155 2 1 Parts List - Mixing Valve — Manual (S01-038) Mixing Valve Parts List Item Part No.
PAGE 19
TDB3108, WF3208 Installation Troubleshooting Vernatherm Thermostatic Mixing Valve (S01-525) — Repair Kit S65-259 Before attempting to troubleshoot the valve or disassemble the components, check for the following conditions: • If stop/check valves are used, make sure that they are fully open. • Make sure that the hot and cold inlet pipes are connected properly, and that there are no crossconnections or leaking stop/check valves.