Transfer Printer THT-BP Precision Quick Operator's Guide Edition 2/05
W.H. Brady Lindestraat 21 Industriepark C3 9240 Zele Belgium Tel.: +32 52 457 811 e-mail: support@brady.be All specifications about delivery, design, performance and weight are given to the best of our current knowledge and are subject to change without prior notice.
THT-BP Precision Thermal Transfer Transfer Printer Printer Quick Operator's Guide Edition 2/05 All rights reserved, including those of the translations.
EU - Conformity Declaration We declare herewith that as a result of the manner in which the machine designated below was designed, the type of construction and the machines which, as a result have been brought on to the general market comply with the relevant fundamental regulations of the EU Rules for Safety and Health. In the event of any alteration which has not been approved by us being made to any machine as designated below, this statement shall thereby be made invalid.
Connecting the Printer Connection to Power Supply The printer is equipped with a wide range power unit (100-240V~), so it is possible to use the printer both with a voltage of 230V~/50 Hz and with a voltage of 115V~/60 Hz without making changes to the printer.
Loading Labels 1 2 3 7 4 5 6 Figure 2 The following steps are valid for loading labels in tear-off mode. Instructions for loading labels in rewind or dispense mode and for loading fanfold labels can be found in the Printer's Operator Manual or in the documentation of the Present Sensor. 1. Loosen the knurled screw (3), swing the media retainer (4) upwards and slide it out as far as possible. 2. Place the media roll (5) onto the media hub (6) and unwind a strip of media from the media roll.
2 8 9 10 Figure 3 8. Slide the media guide ring (7) inward until it lightly touches the side of the media strip. 9. Lower the printhead by rotating the lever (2) counter-clockwise until it locks. 10. When printing narrow label stock, it is necessary to activate the printhead support.
Loading Transfer Ribbon 3 4 5 6 7 1 2 Figure 5 CAUTION ! To avoid premature deterioration of the printhead, make sure the transfer ribbon is slightly wider than the width of label backing. NOTICE ! For direct thermal printing no transfer ribbon is needed ! 1. Raise the printhead assembly (2) by rotating the lever (1) clockwise until it stops. 2. Slide the roll of transfer ribbon (5) as far as possible onto the ribbon supply hub (6). 3.
Adjustment of the Transfer Ribbon 1 3 2 4 Figure 6 In the event that wrinkles appear in the transfer ribbon (1), which cause an inconsistent print image, the transfer ribbon shield (2) can be adjusted to remove the wrinkles. The adjustment should be done during the printing process. 1. The current position is visible on the scale (3). 2. To change the position, rotate the knurled knob (4). Rotating it in the direction of "+" will tighten the transfer ribbon the inner edge of the transfer ribbon.
Control Panel The control panel consists of a graphic display (1) and the Navigator Pad (2) with four integrated keys. Online 1 The control panel display constantly provides the operator with realtime information concerning the current printer mode and label processing. 2 The function and operation of the keys depends on the current mode. The available functions are marked by illuminating the valid symbols and text in the keys.
Functions of the Control Panel in the Offline Menu The Offline Menu contains options to set machine and print parameters, to enter test and service functions as well to operate with the memory card. key while in the ONLINE mode.
Printer Configuration There are a variety of parameters that can be set to configure the printer to specific requirements in the "Setup" menu of the Offline Menu. The setup should be performed when operating the printer for the first time and also when basic changes need to be carried out. In most cases however, simple changes such as heat setting adjustments, using different media will be made with software settings. The "Setup" menu can be protected from unauthorized access by using a code number (PIN).
The following table is an overview about the setup parameters. Further details can be found in the Operator's Manual. Setup Local settings Country Set display language, date and time format Time zone Set Time zone using UTC (Universal Time Coordinated) Daylight saving Select method of daylight saving adjustment Set date Set the printer's date Set time Set the printer's time Machine parameters Printhead pos. X Shift the print image on the label left to right Printhead pos.
Test Options The printer is equipped with several test options, which are summarized in the "Test" menu of the offline menu. 1. Switch from the "Online" mode to the Offline Menu by pressing the key. 2. Press the Press the key or the key until the "Test" menu is displayed. key to confirm the selection. 3. For all test print options load media and transfer ribbon which extends over the entire print width of the printer. 4.
Status Print Sample Figure 8 ASCII Dump Sample Output Label Figure 9 THT-BP Precision Label commands printed in ASCII Dump mode Figure 10 15
Cleaning WARNING ! Before starting any maintenance, power OFF the printer and disconnect the printer from the outlet! General Cleaning During the normal operation of the printer, particles of dust and paper can accumulate inside the printer. Remove these particles with a soft brush or a vacuum. The cover of the printer can be cleaned with a standard cleanser.
