Premier 3-Zone Controller model 140303 Installer Guide Controlador de 3 zonas premier modelo 140303 Guía de instalación Régulateur 3 zones de première qualité modèle 140303 Guide de l’installateur English, 1-11 Español, 12-22 Français, 23-33 140303-100-002
CONTENTS 1 Specifications 4 Configuration 2 Suitable Mounting Locations 5 System Checkout 3 Wiring Diagrams 6 Operation Warning • Read all of the instructions before proceeding. • Always turn off power to the heating/air conditioning system prior to installing or adjusting the Premier 3-Zone Controller. Wire the entire panel before applying transformer power. • This controller should only be installed and configured as described in this manual.
2 Suitable Mounting Locations Mount the Premier 3-Zone Controller panel near the HVAC equipment (see Figure 2). The panel can be mounted in any orientation on a wall, stud, roof truss, or the return-air plenum. For appearance, mount the panel level. Remove the panel cover and use the base as a template to drill mounting holes 6.5” apart (see Figure 3). Attach the panel with appropriate screws (not included). Use mounting anchors as needed for drywall or plaster installations.
3 Wiring the Panel Always turn off power to the heating/air conditioning system prior to installing or adjusting the Premier 3-Zone Controller. Wire the entire panel before applying transformer power. Use the following general wiring instructions for all systems. Specific wiring will vary depending on the equipment and type of system (conventional or heat pump). 3.1 Damper Wiring Install the system dampers using the instructions provided by the manufacturer.
3.2 Thermostat Wiring Install the system thermostats using the instructions provided by the manufacturer. Connect the thermostats to the zone panel as shown. Notes: • Wiring to the C terminal is required only for thermostat power. • E terminal at thermostat 1 controls emergency heat. See E-Heat Switch Installation Sheet 149090 for wiring details. Rh E Rc R Y Y G G W W C C Thermostat Zone Panel 3.
3.5 Conventional System Wiring Note: For a heat pump system, see Section 3.6. Connect a conventional heating system to the zone panel as shown. HOT RH 24 VAC RC For a single stage heating and cooling system, the 2nd stage connections are not used. For a system using a dual transformer, open jumper J1 (see Configuration section, Figure 4). Make sure the the neutrals (common) are connected.
4 Configuration Use the following instructions to configure the Premier 3-Zone Controller. 1. Open J1 jumper for dual transformer installations. 2. Open J2 short cycle protection jumper for system test. Note: Replace J2 when system testing is completed or leave J2 open if compressor has built in short cycle protection. 3. Press ▲ and then press ▲ to raise or ▼ to lower the Hi Temp cutout. 4. Press ▼ and then press ▲ to raise or ▼ to lower the Low Temp cutout. 5.
6. Set the DIP switches to meet system requirements.
[ ] Verify green power LED near 24 VAC terminals is lit. [ ] Verify green heartbeat LED in middle of panel is pulsing. [ ] Verify all 3 zone LEDs near damper terminals are green. [ ] Verify supply temp display shows current plenum temperature. [ ] Switch zone 1 thermostat to heat mode, and call for heat in zone 1 by raising set temperature above room temperature. [ ] Verify zone 1 damper LED stays green (open) and zone 2 and 3 damper LEDs change to red (closed).
6 Operation The Premier 3-Zone Panel has LEDs and a built-in display to tell the installer and homeowner the current operating mode of the panel. Refer to Figure 5 and the following descriptions of the panel LEDs for operation information. LED Display Panel Supply Temp Shows the current air supply temp. Use to set Hi/Lo temp limit. Hi Temp Press ▲ to display Hi temp cutout setting. Press ▲ to raise or ▼ to lower Hi temp setting. Lo Temp Press ▼ to display Lo temp cutout setting.
LED display panel SUPPLY TEMP HI TEMP LO TEMP PURGE DELAY RC W C ▲ G Braeburn 7 G W C G W SA2 5 NON HP NORMAL REV VALVE B FAN GAS OPP CALL 20 LOCKOUT NONE PRIORITY ALL G2 W/2-ZONES HEAT PUMP DUAL FUEL O ELEC/HP 15 ACTIVE ZONE1 2-STAGES EMERGENCY HEAT ON OFF Z1-PO COM Z1-PC Z2-PO COM Z2-PC Z3-PO PWR 24V COM 24C Z3-PC DAMPER 3 C DAMPER 2 Y SA1 FLASHING WHEN NORMAL Y W1 AUX W2 O/B C 3-Zone R R J2-SHORT CYCLE PROTECTION DAMPER 1 THERMOSTAT3 2 Y SUPPLY TEMP THERMOSTAT2 1
Warranty Braeburn Systems LLC warrants each new Braeburn zone panel against any defects that are due to faulty material or workmanship for a period of five years after the original date of purchase by a professional service technician. This warranty and our liability does not apply to merchandise or the zone panel resulting from accident, alteration, neglect, misuse, improper installation or any other failure to follow Braeburn installation and operating instructions.
