Manual

ManualsBrandsBraeburn ManualsEquipment3200

WARNING

Important Safety Information

Premier Series

Non-Programmable Thermostats

Speciﬁcations

Installation

Testing Your New Thermostat

Programming User Settings

Temperature Adjustment

Speciﬁcations

• Electrical Rating: 24 Volt AC (18-30 Volt AC)

1 amp maximum load per terminal

2 amp total maximum load (all terminals) (Model 3000)

3 amp total maximum load (all terminals) (Model 3200)

• Control Range: 45˚ - 90˚ F (7˚ - 32˚ C)

• Accuracy: +/- 1˚ F (+/- .5˚ C)

• AC Power: 18-30 Volt AC

• DC Power: 3.0 Volt DC (2 AA Alkaline batteries included)

Additional Operation

Features

Battery Replacement

Trouble Shooting

Wiring Diagrams

• Always turn off power to the air conditioning or heating system prior to

installing, removing, cleaning or servicing thermostat.

• This thermostat requires either 24 Volts AC Power or two (2) properly installed

“AA” alkaline batteries for normal operation and control of the heating or

cooling system.

• This thermostat should only be used as described in this manual. Any other

use is not recommended and will void the warranty.

Speciﬁcations

• Model 3000: Compatibility with low voltage single stage gas, oil or electric

heating or cooling systems, including single stage heat pumps; can also

be used on 250mv to 750mv millivolt heating only systems.

• Model 3200: Compatibility with low voltage multi-stage gas, oil or electric

heating or cooling systems, including multi-stage heat pumps.

• Terminations, Model 3000: Rc, Rh, B, O, Y, W, G, C

Terminations, Model 3200: R, O, B, C, Y1, Y2, E/W1, W2, G, L

cont.

Replacing Existing Thermostat

Installation

1. Always turn off power to the air conditioning or heating system prior to

removing existing thermostat.

2. Remove the cover of your old thermostat and locate the wire terminals.

Do not remove wires from terminals until step 3 is completed.

3. Using small pieces of masking tape, label wires prior to removal from

terminals. Use the chart below to determine the new terminal designations

for your new thermostat.

Old Terminal from

Existing Thermostat

New Terminal for

New Thermostat

(Model 3000)

New Terminal for

New Thermostat

(Model 3200)

Terminal

Description

V or Rc Rc Cooling

Transformer

M, 4, Rh, or R Rh Heating

Transformer

R, V-VR or VR-R R 24 VAC

G or F G G Fan Control

H, W or 4 W Heating Control

W1, W2, W-U or E E/W1 Emergency Heat /

1st Stage Heat

W2 W2 2nd Stage Heat

Y Y Cooling Control

Y, Y1 or M Y1 1st Stage

Compressor

Y2 Y2 2nd Stage

Compressor

B B B Reversing Valve

(Heating)

O O O Reversing Valve

(Cooling)

C C C 24 VAC Common

L or X L System Status LED

4. After labeling and removing all wires from terminals, unscrew the existing

thermostat sub-base from wall. Secure wires to prevent them from slipping into

the hole in the wall.

MODEL

3000

MODEL

3200

Multi-Stage 2 Heat / 2 Cool

Conventional and Heat Pump

Single Stage Heat / Cool

Conventional and Heat Pump

Before Installing, Programming or Operating,

PLEASE READ ALL INSTRUCTIONS

Summary of content (7 pages)

PAGE 1
Specifications cont. Premier Series Non-Programmable Thermostats MODEL 3000 MODEL 3200 Single Stage Heat / Cool Conventional and Heat Pump 2 Installation Multi-Stage 2 Heat / 2 Cool Replacing Existing Thermostat Conventional and Heat Pump 1. Always turn off power to the air conditioning or heating system prior to removing existing thermostat. 2. Remove the cover of your old thermostat and locate the wire terminals. Do not remove wires from terminals until step 3 is completed. 3.
PAGE 2
Installation cont. 2 Installation cont. NOTE–MODEL 3000: This thermostat is designed for use with 24 Volt-AC low voltage single stage gas, oil or electric heating or cooling systems, including single stage heat pumps and can also be used on 250mv to 750mv millivolt heating only systems. Do not use this thermostat on applications with voltages above 30 Volts AC.
PAGE 3
Testing Your New Thermostat cont. 6. The cooling system should start within several seconds. Place the system switch in the OFF position. The cooling system should stop within a few seconds. 7. Place the fan switch in the ON position. The system blower should start. 8. Place the fan switch in the AUTO position. The system blower should stop. 4 Programming User Settings Default Thermostat Settings Function Status After Reset Operation Mode Normal Operating Mode Room Temperature 70˚ F (21.
PAGE 4
5 Temperature Adjustment cont. 2. The display will return to normal operating mode when the or buttons are released. The SET indicator will turn off, indicating that the current temperature shown in the display is the room temperature. Changing Set Temperature 1. Press and hold the or button for more than 1 second. The entire display will flash once and the SET indicator will be flashing. Release the or button and press the or button again to adjust the set temperature. 2.
PAGE 5
6 Additional Operation Features cont. COOL: Symptom: Thermostat turns on heating instead of cooling or cooling instead of heating. Potential Solution: Check thermostat wiring to make sure that the heating and cooling stages are connected to the correct terminals on the wiring terminal block. See Section 9. This will turn on whenever the system switch is in the cool mode. “COOL” will flash when the cooling system is running.
PAGE 6
9 Wiring Diagrams cont. Symptom: Cannot program a set point temperature higher than 90˚ F (32˚ C). Potential Solution: This is above the normal thermostat temperature setting range of 45˚ to 90˚ F (7˚ to 32˚ C). MODEL 3000: Conventional Systems (Dual Transformer) Rc Rh Symptom: Cannot program a set point temperature lower than 45˚ F (7˚ C). Potential Solution: This is below the normal thermostat temperature setting range of 45˚ to 90˚ F (7˚ to 32˚ C).
PAGE 7
9 Wiring Diagrams cont. MODEL 3200: Conventional Systems O C B Y1 Y2 E/W1 W2 1st Stage Heat Control 1st Stage Compressor Control Transformer Common (See NOTE 1) R G Premier Series L Non-Programmable Thermostats Fan Control LIMITED WARRANTY 2nd Stage Heat Control 2nd Stage Compressor Control (See NOTE 2) Neutral 24 VAC 120 VAC Hot NOTES: 1. Transformer Common connection not required for battery-only operation of thermostat. 2.