User manual

ManualsBrandsBraeburn ManualsConsumer electronics5300

MODEL

5300

Premier Series

Universal Auto Changeover

Up to 3 Heat / 2 Cool Heat Pump or

2 Heat / 2 Cool Conventional Thermostat

USER

MANUAL

READ ALL INSTRUCTIONS

BEFORE PROCEEDING

Braeburn Systems LLC, as an Energy Star

partner has determined that this product

meets the Energy Star Guidelines developed

by the U.S. Environmental Protection Agency

& the U.S. Department of Energy for

maximum energy efﬁciency.

CONTENTS

QUICK REFERENCE

PROGRAMMING

USER SETTINGS

QUICK REFERENCE

ADDITIONAL OPERATION FEATURES

TROUBLESHOOTING

SYSTEM Button: Selects AUTO (Heat/Cool), COOL, OFF,

HEAT or EMER.

PROG Button: Press to enter the program setup mode where

you can select the time, temperature and fan setting for each

program period. Scrolls backward between user/installer

setup screens.

HOLD Button: Enables or disables extended hold mode or

temporary program override.

RETURN Button: Press and hold for 4 seconds to enter the

user settings mode (see user manual). Scrolls between user/

installer setup screens. Returns unit to normal mode when

in program mode.

DAY/TIME Button: Enters time and day setting mode.

Selects individual days in program mode.

FAN Button: Selects AUTO, ON, CIRC (recirculate) and

PROG (program) modes.

RESET Button: Resets time, program and some user settings back to the factory default. See section 4 for a list of functions

that will return to their factory default settings after the RESET button is pressed.

Button: Turns on backlight for 10 seconds.

Button: Increases setting (time, temperature, etc.). Scrolls between option settings.

Button: Decreases setting (time, temperature, etc.). Scrolls between option settings.

model 5300 shown with cover open

Press and hold both buttons at the same time to view the outdoor temperature if an outdoor sensor is connected.

Summary of content (15 pages)

PAGE 1
CONTENTS MODEL 5300 USER MANUAL READ ALL INSTRUCTIONS BEFORE PROCEEDING Braeburn Systems LLC, as an Energy Star partner has determined that this product meets the Energy Star Guidelines developed by the U.S. Environmental Protection Agency & the U.S. Department of Energy for maximum energy efficiency.
PAGE 2
USER SETTINGS 2 PROGRAMMING 2 PROGRAMMING USER SETTINGS 2.1 Setting Current Time of Day and Day of Week 2.3 Setting Thermostat System Selection The system can be selected by pressing the System button. There are five possible settings to select from – AUTO, COOL, OFF, HEAT and EMER. NOTE: It is important for you to correctly set the current time of day (note AM/PM indicator in display), and the current day of week to avoid problems with program execution. 1.
PAGE 3
USER SETTINGS 2 PROGRAMMING 2 PROGRAMMING USER SETTINGS cont. 2.4.1 Setting the First, Second and Third Stage Differentials First Stage Differential The default setting is 0.2˚ F (0.1˚ C). The room temperature must change 0.2˚ F (0.1˚ C) from the set point temperature before the thermostat will initiate the system in heating or cooling. 1. In normal mode, press and hold the RETURN button for four seconds. The LCD display will show “d1 SET X” where “X” equals the ˚F / ˚C differential setting.
PAGE 4
2 PROGRAMMING USER SETTINGS cont. 2 PROGRAMMING USER SETTINGS cont. 2.4.5 Setting the Extended Hold (Vacation) Mode (continued - see section 3.6) 2.4.8 Setting the Multi-Level Keypad Lockout Code (see section 3.10) NOTE: 19. Press and hold the RETURN button for four seconds. Press RETURN button repeatedly until 000 SET LOCK is displayed. 20. Press the or button to enter a 3 digit code, using the RETURN button to store each digit and move to the next digit.
PAGE 5
2 PROGRAMMING USER SETTINGS 2 PROGRAMMING USER SETTINGS cont. 2.5 Setting Your Energy Saving Programs – Tips Before Starting (continued) 2.5 Setting Your Energy Saving Programs (continued) • This thermostat is preprogrammed with 4 events per day, with times and temperatures recommended by the Environmental Protection Agency and the U.S. Department of Energy in their ENERGY STAR® program. These settings provide efficient energy savings during normal heating and cooling modes of operation.
PAGE 6
2 PROGRAMMING USER SETTINGS cont. 2 PROGRAMMING USER SETTINGS cont. 2.5 Setting Your Energy Saving Programs (continued) Entering Your Program–7 DAY, Residential Mode (continued) • Independent heating and cooling temperatures are available in auto changeover mode. Independent program times and fan settings for heating and cooling are NOT available in auto changeover mode.
PAGE 7
2 PROGRAMMING USER SETTINGS cont. 2 PROGRAMMING USER SETTINGS cont. Programming Instructions–7 DAY, Residential Mode (continued) Entering Your Program–7 DAY, Commercial Mode 2. If you wish to program each day individually, press the DAY/TIME button to select each day. 3. Press the or button to change the time to the desired hour in one hour increments. Press the PROG button. The minute portion of the set point time will begin flashing. 4.
PAGE 8
2 PROGRAMMING USER SETTINGS cont. Entering Your Program – 5-2 DAY Residential Mode The 5-2 Day mode has separate Weekday and Weekend Program Groups that allow you to change the daily set point times and temperatures to meet your individual schedule needs. Weekday – allows you to program all the weekdays (M, TU, W, TH, F will show in display) at the same time. Allows programming times and temperature settings for four set points (MORN, DAY, EVE and NIGHT) to meet your weekday schedule needs.
PAGE 9
3 ADDITIONAL OPERATION FEATURES cont. 4. The display will return to normal mode after 30 seconds or by pressing the RETURN button. 5. By selecting the opposite system mode (HEAT or COOL) with the system button you can review or change the set temperature for that mode. NOTE: If Auto Changeover is enabled in the Installer Options, and a setting is made in either heating or cooling which violates the dead band, the opposite mode will adjust up or down automatically to maintain the dead band spacing.
PAGE 10
3 ADDITIONAL OPERATION FEATURES cont. 3 ADDITIONAL OPERATION FEATURES 3.6 Extended Hold (Vacation) Mode 3.9 Humidifier Pad Monitor (see section 2.4.4 for setting) 1. Press the HOLD button to bypass the program schedule. The current set point temperature will be held until the HOLD condition is released. HOLD will show in the display. 2. Press the HOLD button again to return the thermostat to normal program operation. 3.
PAGE 11
3 ADDITIONAL OPERATION FEATURES cont. 3 ADDITIONAL OPERATION FEATURES cont. 3.11 Adaptive Recovery Mode (ARM™) 3.12 Recirculating Fan Feature (see section 2.4.9) In order to maximize comfort and energy efficiency, this thermostat is equipped with Adaptive Recovery Mode (ARM™).
PAGE 12
3 ADDITIONAL OPERATION FEATURES cont. 3.15 Compressor Protection and AC Power Monitor This thermostat includes an automatic compressor protection feature to avoid potential damage to the compressor system from short cycling. This thermostat automatically provides a delay (see section 4 of the Installer Guide) after turning off the system output to protect the compressor. This protection is also present in the heat mode of operation on single stage heat pump systems to protect the compressor.
PAGE 13
4 TROUBLESHOOTING 4 TROUBLESHOOTING Symptom: Fan continues to run in cooling mode when the system has turned off. Potential Solution: The Residual Cooling Fan Control Feature can allow up to a 90 second fan delay after cooling system shutdown for energy efficiency gains. The default setting is 60 seconds. This can be changed to disable this feature or shorten the time period if desired (see section 4 of the Installer Guide). Symptom: Thermostat will not follow program set points.
PAGE 14
4 TROUBLESHOOTING cont. Symptom: HI is shown in the thermostat display where the room temperature is normally displayed. Potential Solutions: The temperature sensed by the thermostat is higher than the 99˚ F (37˚ C) upper limit of the SYMPTOM POTENTIAL SOLUTION thermostat’s display range. The display will return to normal after the sensed temperature lowers within the 40˚ to 99˚ F (5˚ to 37˚ C) display range. Turn on the cooling system or use other methods to lower the temperature.
PAGE 15
5 YEAR LIMITED WARRANTY Store this booklet for future reference Braeburn Systems LLC warrants each new Braeburn thermostat against any defects that are due to faulty material or workmanship for a period of five years after the original date of purchase by a professional service technician.