User manual
14
Entering Your Program – 5-2 DAY Residential Mode
The 5-2 Day mode has separate Weekday and Weekend Program Groups that allow you to change the daily
set point times and temperatures to meet your individual schedule needs.
Weekday – allows you to program all the weekdays (M, TU, W, TH, F will show in display) at the same time. Allows
programming times and temperature settings for four set points (MORN, DAY, EVE and NIGHT) to meet your weekday
schedule needs.
Weekend – allows you to program all the weekend days (SA, SU will show in display) at the same time. Again
allows programming times and temperature settings for four set points (MORN, DAY, EVE and NIGHT) to meet your
weekend schedule needs.
1. Press the PROG button to enter the Program setting mode. Press
the SYSTEM button to select HEAT to set heating times and
temperatures. MORN set point of the Weekday Program Group will
be displayed. The display will show M, TU, W, TH, F to indicate the
Weekday group is being programmed. The hour portion of the
set point time and the AM/PM indicator will be flashing.
2. Press the or button to change the time to the desired hour in one hour increments. Press the PROG button.
The minute portion of the set point time will begin flashing.
3. Press the or button to change the time to the desired minute in 10-minute increments. Press the PROG
button. The SET temperature will begin flashing.
4. Press the or button to change the set point temperature to the desired setting in 1º increments.
Press the PROG button. The FAN mode will begin flashing.
2
PROGRAMMING
USER SETTINGS
cont.
NOTE: The fan option is not available or displayed if the Fan LOCK was enabled during Installer Setup.
5. Press the or button to select AUTO or ON. Press the PROG button. The thermostat will now display
the DAY set point time and temperature. Again, you will see the hour portion of the set point time and the
AM/PM indicator will be flashing.
6. Follow steps 3 through 5 to set the set point times, temperatures and fan mode for the periods of DAY, EVE
and NIGHT.
2
PROGRAMMING
USER SETTINGS
cont.
15
Entering Your Program – 5-2 DAY Residential Mode (continued)
7. After pressing the PROG button, you will enter the Weekend Program Group. The display will show SA, SU
to indicate the Weekend Group is being programmed. The hour portion of the MORN set point time and the
AM/PM indicator will be flashing.
8. Follow steps 3 through 6 to set the set point time, temperatures and fan mode for the periods of DAY, EVE
and NIGHT.
9. Press the SYSTEM button to select COOL to set cooling times and temperatures. The display will show COOL.
Follow steps 3 through 6 to set the set point times, temperatures and fan mode for the COOL mode.
10. Press the RETURN button to return to the normal mode, or wait 30 seconds for the thermostat to
return automatically.
NOTE: If you make an error and want to start over, you may erase all programs. To erase all entered programs,
current time of day, day of week and other user settings, gently press the RESET button using a paper clip or a
small pencil tip. This will return all thermostat settings to their default values. A reset will also clear any changes
to the differential settings made in section 2.4.1.
3.1 Review/Change Set Temperature, Non-Programmable Mode
1. Press and hold the or button. The current set point temperature
will be displayed in the place of the current room temperature,
and the indicator SET will be displayed.
2. The display will return to normal operating mode when the or
button is released. Continuing to hold the or button for one
second or longer will allow the user to change the current
set point temperature.
3. Press and hold the or button for 1 second. The entire display will flash once and the SET indicator will be
flashing. Release the or button and press the or button again to adjust the set point temperature.
3
ADDITIONAL
OPERATION FEATURES