Datasheet

ManualsBrandsBrainboxes Manualselectrical equipment & suppliesED-527

Connect, Congure, Control

ED-527 ETHERNET TO Digital IO 16 Outputs

Ethernet to Digital Out

ED-527

• 16 Digital Outputs

• Drives high current and high voltage loads

• Ideal for inductive, capacitive & resistive loads

• Gateway Port for NuDAM/ADAM modules

• -30

C to +80

C Temperature range

• +5V to +30V DC Input Power

ED-527

Digital Channels

Outputs Output Channels 16 non-isolated output channels

Maximum output current

Sinks up to 1 Amp per pin, 40V max load

Max combined load 4.0 Amps per ED device

Characteristic: Open drain output, protected MosFET with intelligent short circuit

protection up to 36V

Over temperature shutdown:175

C typical 150

C min

Maximum output load Voltage

40V

ESD Protection

16kV

1 2 3 4 5 6

654321

Date: Sheet of

Drawn By: Checked By:

Number Revision

Title

D OUT1 (Pin 3)

GND (Pin 1)

D OUT0 (Pin 2)

D OUT3 (Pin 5)

D OUT2 (Pin 4)

D OUT1 (Pin 3)

GND (Pin 1)

D OUT0 (Pin 2)

D OUT3 (Pin 5)

D OUT2 (Pin 4)

EXTERNAL GROUND

ALWAYS CONNECT

External CircuitExternal Circuit

Bit=1

Bit=0

UN_OUT02

SWITCH

UN_OUT02

1K1K

24VOLTS 24VOLTS

10-7-2013_16:19

?EAMONN

90ED073R2

ETHERNET TO DIO 7 DI 3DO 2 PORT SWITCH

ED-588ED-588

Resistor current= 0

OUTPUT PIN=24V

ALWAYS CONNECT

EXTERNAL GROUND

OUTPUT PIN=~0V

Resistor current= 24mA

LAMP= ONLAMP= OFF

Driving an Andon Light

Summary of content (8 pages)

PAGE 1
Ethernet to Digital Out ED-527 ED-527 ETHERNET TO Digital IO 16 Outputs ED-527 • 16 Digital Outputs • Drives high current and high voltage loads • Ideal for inductive, capacitive & resistive loads 1 2 3 4 5 • Gateway Port for NuDAM/ADAM modules • -30oC to +80oC Temperature range • +5V to +30V DC Input Power A Digital Channels Outputs B Output Channels 16 non-isolated output channels Maximum output current Sinks up to 1 Amp per pin, 40V max load Max combined load 4.
PAGE 2
ED-527 Ethernet 16 DO Usage Model for ED-527 Digital Outputs Ethernet Connection Gateway RS485 Digital Outputs 5V Power Power from laptop for configuration 24V Power Dual redundant power supply ASCII software commands - LabView, MATLAB, Agilent VEE Remote access for maintenance and monitoring Integral horsepower motors Relays Stepper Motors Lighting Contactors Andon Lights Heating Starters Fans/ Air conditioning systems Fluid and fuel flow Two-position actuators Alarms/ Safety devices
PAGE 3
ED-527 Ethernet 16 DO 8 Digital Outputs RS485 Gateway for NuDAM/ADAM Modules Easy to use Interface: Great features for remote monitoring Integral DIN rail mount Ethernet port LED Status Indication 8 Digital Outputs +5V to +30V Power Supply Ethernet to DIO Device Server: The Ethernet to DIO device is implemented using a Windows COM port driver that is completely compatible with all popular PC packages such as LabView, MATLAB and Agilent VEE and support a range of popular APIs.
PAGE 4
ED-527 Ethernet 16 DO Grounding: Correctly wired grounds help cut down on electromagnetic interference 5 pin terminals allow a ground on the 5th pin of each block Functional earth connection to the DIN rail Gateway RS485 Serial Port: Half duplex RS485 port allows connection and control of industry standard NuDAM, eDAM and ADAM modules modules using ASCII protocols. Wide Range Redundant Dual Power Input: +5VDC to +30VDC accommodates variation in the +24VDC factory floor and allows alternative power sources.
PAGE 5
ED-527 Ethernet 16 DO Familiar ASCII Command Protocol: The ED range of devices uses the de facto industry standard ASCII command protocol implemented in the popular ADAM/NuDAM/EDAM modules. Typical examples include: $01M read the name of device address 01 !01ED-588 device 01 replies that its name is ED-588 $01F read firmware version number of device address 01 !012.54 firmware version of device 01 is 2.
PAGE 6
ED-527 Ethernet 16 DO Browser Interface Webserver Interface Configure IP address, monitor state of i/o lines, set the Watchdog Timers Output Reset Value, Set Power on digital output value Programming Interface No device driver needed, just open a TCP connection and send simple ASCII commands.
PAGE 7
ED-527 Ethernet 16 DO Connectors Screw Terminals 3.5mm pitch, #22 - #14, 0.5mm2-2.5mm2 pin power supply Wire Thickness 0.150 inch, 3.81mm, 20 pins, 12+8 screw terminals, #26 - #16 AWG, 0.14mm2-1.3mm2 Power Supply Environmental Power Consumption 2.
PAGE 8
ED-527 Ethernet 16 DO Packaging Information Packaging Installation CD including manual, Microsoft signed drivers & utilities, Quick Start Guide Device Ethernet 16 DO Packaged Weight 0.215 kg, 0.47 pounds Packaged Dims 235(l) x 170(w) x 62(h) mm, 9.25(l) x 6.69(w) x 2.