A PROUD HERITAGE OF EXPERIENCE & QUALITY DISHWASHER BR-DWSH01-S , 1 6 7 $ / / $ 7 , 2 1 , 1 6 7 5 8 & 7 , 2 1 6 W W W . V I N O T E M P .
Installation Instructions BEFORE YOU BEGIN Read these instructions completely and carefully. IMPORTANT– Observe all Dishwasher IMPORTANT – The dishwasher MUST be installed to allow for future removal from the enclosure if service is required. If you received a damaged dishwasher, you should immediately contact your dealer or builder. governing codes and ordinances. • Note to Installer – Be sure to leave these instructions for the consumer’s and local inspector’s use.
Installation Preparation PARTS SUPPLIED: Four flat head wood screws to secure dishwasher to underside of countertop (in literature package). Screw type hose clamps and one drain hose. 2 top mounting clips.
Installation Preparation • The dishwasher must be installed so that drain hose is no more than 10 feet in length for proper drainage. • The dishwasher must be fully enclosed on the top, sides and back, and must not support any part of the enclosure. CLEARANCES: When installed into a corner, allow 2" min. clearance between dishwasher and adjacent cabinet, wall or other appliances. Allow 25-5/8" min. clearance from the front of the dishwasher for door opening.
Installation Preparation PREPARE ELECTRICAL WIRING WARNING FOR PERSONAL SAFETY: Remove house fuse or open circuit breaker before beginning installation. Do not use an extension cord or adapter plug with this appliance. 1-1/2" Dia. Hole (Max.) 2½~3½ in. (65 ~ 90mm) Electrical Requirements • This appliance must be supplied with 120V, 60 Hz., and connected to an individual properly grounded branch circuit, protected by a 15 or 20 ampere circuit breaker or time delay fuse.
Increase Decrease
Installation Instructions STEP 4 INSTALL POWER CORD STEP 2 ADJUST LEVELING LEGS Skip this step if dishwasher will be direct wired. Use power cord kit WX09X70910 available for purchase from an authorized GE parts dealer. The power cord and connections must comply with local codes and ordinances. • Recommended power cord length is 54" min. and 64" max. • Move the dishwasher close to the installation location and lay it on its back.
Installation Instructions STEP 9 POSITION DISHWASHER UNDER COUNTERTOP Reposition Dishwasher by Grasping Both Sides With Hands • Check to be sure that wires are secure under the dishwasher and not pinched or in contact with door springs or other dishwasher components. TIP: Check tub insulation blanket, if equipped. It should be positioned so it is not bunched up or interfering with door springs. Check by opening and closing the door. • Push dishwasher into cabinet.
hole Installation Instructions STEP 11 SECURE DISHWASHER TO THE COUNTERTOP For countertops made of wood or that will not be damaged by drilling,use Method 1. For countertops made of granite,marble,or other materials that could be damadged by drilling,use Method 2. Installation bracket IMPORTANT –Drive screws straight and flush. Protruding screw heads will scratch the top of the control panel and can interfere with door closing.
Installation Instructions STEP 13 CONNECT DRAIN LINE DRAIN LINE INSTALLATION FOLLOW ALL LOCAL CODES AND ORDINANCES. • Connect drain line to air gap, waste tee or disposer using either previously determined method. The drain hose molded end will fit 5/8", 3/4" or 1" diameter connections on the air gap, waste tee or disposer. Cut on the marked line as required for your installation.
Installation Instructions STEP 14 CONNECT POWER SUPPLY STEP 15 PRE-TEST CHECKLIST Review this list after installing your dishwasher to avoid charges for a service call that is not covered by your warranty. Skip this step if equipped with power cord. Verify that power is turned off at the source. • Remove junction box cover “A”. • Locate the three dishwasher wires, (white, black and green) with stripped ends. Insert dishwasher wires through the small hole in the junction box “B”.
Installation Instructions STEP 16 DISHWASHER WET TEST STEP 17 REPLACE TOEKICK Turn on power supply (or plug power cord into outlet, if equipped). Turn on your dishwasher (please refer to the Owner's Manual for instructions). Close door, select RINSE ONLY cycle and press START/CANCEL. . Check to be sure that water enters the dishwasher If water does not enter the dishwasher, check to be sure that water and power are turned on. Check for leaks under the dishwasher.
