Rear Vision System – Tailgate Emblem Camera Aftermarket Display 2009-Current Ford F-150 and 2010-Current Super Duty (Kit part number 1008-6509) Kit Contents: Tools Required: Tailgate Emblem Mount with Camera T30 Torx Driver Chassis Harness with RCA (Note: In some cases a 7mm, 8mm, and 10mm Sockets RCA extension may be required to connect to Flat Head Screwdriver your aftermarket display.
TABLE OF CONTENTS Pages Section 1: Camera Mount Preparation 3-4 Section 2: Cut Pickup Bed Opening (if required) 5 Section 3: Camera Installation 6 Section 4: Chassis Harness Installation 7-9 Section 5: Ignition, Reverse and Ground Locations 10-14 Section 6: Reference 6A: Supplied Camera and Chassis Harness Pinouts 6B: Previous Model Year Ignition and Reverse Locations 15 16-23 6509 Instructions 6-18-12 F series (1).
Section 1: Camera Mount Preparation 1. Lower tailgate and remove upper sheet metal cover by removing the eight screws with a T30 Torx bit (Figure 1). Figure 1 5. If camera mounting holes and harness opening were present in the existing tailgate, proceed to Step 8. If not, align the supplied 1008-9100-03 template to the two existing emblem locating holes. 6. Mark and center punch the location for the two retaining clip holes and the camera and harness access opening (Figure 3). Figure 3 2.
Section 1: Camera Mount Preparation continued 9. Drill a pilot hole for the camera mount. Using a 1¾ inch hole saw, cut the camera harness opening. Trial fit camera mount and file opening as necessary (Figure 5). Figure 5 10. Apply Z-tech to camera harness opening. 6509 Instructions 6-18-12 F series (1).
Section 2: Cut Pickup Bed Opening Follow Steps 12 through 16 only if the vehicle does not have an opening in the bed above the license plate per Figure 6 Figure 6 14. Center punch the mark and drill a pilot hole. Next, cut a 1 inch opening with a hole saw (Figure 8). Figure 8 12. Prepare a clean, flat work surface for tailgate. Remove tailgate retaining straps. With an assistant, remove the tailgate by lifting away from lower tension pins, and set tailgate aside. 13.
Section 3: Camera Installation 17. Mounting Camera 17a. Remove material between camera opening and round hole for harness clearance (apply supplied Z-tech to any exposed bare metal with a small brush). Insert the two retainer clips (Figure 10). 18. Run camera harness through opening in the base of the tailgate and seat grommet in pickup bed (Figure 11). Figure 11 Figure 10 17b. Route the camera harness through tailgate opening (Figure 1O.5). 19.
INSTALLATION INSTRUCTIONS Section 4: Chassis Harness Installation Figure 14 20. Remove the driver side sill plate with a trim tool (Figure 12). Figure 12 21. Loosen driver side A-pillar molding with hands and then remove the driver side lower kick panel (Figure 13). 23. Secure Super Duty template number 1008-9100-01 (Figure 15) or secure F150 template number 1008-9100-02 over opening in front of driver’s seat (Figure 16). Figure 15 Figure 13 Figure 16 22. Pull back carpet in front of driver’s seat.
INSTALLATION INSTRUCTIONS Section 4: Chassis Harness Installation continued Figure 19 24. Center punch and drill a pilot hole then drill a 1 inch hole with a hole saw. 25. Clean the hole with a deburring tool (Figure 17). Figure 17 26. Apply supplied Z-tech with a small brush (Figure 18). Figure 18 27. Route the supplied chassis harness through the drilled opening and seat the grommet from the inside of vehicle (Figure 19). 6509 Instructions 6-18-12 F series (1).
INSTALLATION INSTRUCTIONS Section 4: Chassis Harness Installation continued Figure 22 28. Route the exterior portion of the supplied chassis harness along existing vehicle chassis harness and over fuel tank. Using supplied tie wraps, secure the harness to existing wiring at 2 inch intervals (Figures 20 and 21). Figure 20 30. Plug the chassis harness into the camera harness installed earlier under the pickup bed (Figure 23). Figure 23 Figure 21 29.
INSTALLATION INSTRUCTIONS Section 5: Ignition, Reverse and Ground Locations 31. If needed, install aftermarket display or navigation display per instructions. 32. Remove the passenger side door sill plate with a trim tool and remove passenger side kick panel with hands, just disengaging the two clips from the sheet metal (Figure 24). Figure 25 Figure 24 33. Route the supplied chassis harness green, red, and black wires along the vehicle cross dash harness as shown.
INSTALLATION INSTRUCTIONS Section 5: Ignition, Reverse and Ground Locations continued Diagram A Supplied Chassis Harness Chassis Harness Ignition & Reverse Locations Model F150 Super Duty Year(s) 2012 (late production) 2012 (late production) Function Connector Dia. Page Ignition C2280B 12 Reverse C2280D 13 Ignition C2280B 14 Reverse C2280D 13 NOTE: For previous years pinouts, please refer to Section 6B. 6509 Instructions 6-18-12 F series (1).
INSTALLATION INSTRUCTIONS Section 5: Ignition, Reverse and Ground Locations continued Ignition Connector C2280B – 2012 late production F150 6509 Instructions 6-18-12 F series (1).
INSTALLATION INSTRUCTIONS Section 5: Ignition, Reverse and Ground Locations continued Reverse Connector C2280D – 2012 late production F150 and Super Duty 6509 Instructions 6-18-12 F series (1).
INSTALLATION INSTRUCTIONS Section 5: Ignition, Reverse and Ground Locations continued Ignition Connector C2280B – 2012 late production Super Duty 6509 Instructions 6-18-12 F series (1).
INSTALLATION INSTRUCTIONS Section 6A: Reference – Supplied Camera & Chassis Harness Pinouts PIN # FUNCTION 1 Video (+) CAMERA HARNESS COLOR White CHASSIS HARNESS COLOR White 2 Shield Blue Blue 3 Reverse Green Green 4 Video (-) Brown Brown 5 Ground Black Black 6 Ignition Red Red Loose wires provided in the Supplied Chassis Harness Function Ground (-) Reverse signal 12V Ignition 12V 6509 Instructions 6-18-12 F series (1).
INSTALLATION INSTRUCTIONS Section 6B: Reference – Previous Model Year Ignition and Reverse Locations Supplied Chassis Harness Model F150 F150 F150 Super Duty Super Duty Year Connector Dia. Page Ignition C270J 17 Reverse C270E Ignition Function Location Pin Color Right Kick 2 White / L. Blue Red 18 Right Kick 20 Black / Pink Green C270J 17 Right Kick 2 White / L.
INSTALLATION INSTRUCTIONS Section 6B: Reference – Previous Model Year Ignition & Reverse Locations continued Ignition Connector C270J – 2004 – 2008 F-150 6509 Instructions 6-18-12 F series (1).
INSTALLATION INSTRUCTIONS Section 6B: Reference – Previous Model Year Ignition & Reverse Locations continued Reverse Connector C270E – 2004 F150 6509 Instructions 6-18-12 F series (1).
INSTALLATION INSTRUCTIONS Section 6B: Reference – Previous Model Year Ignition & Reverse Locations continued Reverse Connector C270B – 2005-2008 F150 6509 Instructions 6-18-12 F series (1).
INSTALLATION INSTRUCTIONS Section 6B: Reference – Previous Model Year Ignition & Reverse Locations continued Ignition Connector C2280D – 2009-2012 (early production) F150 6509 Instructions 6-18-12 F series (1).
INSTALLATION INSTRUCTIONS Section 6B: Reference – Previous Model Year Ignition & Reverse Locations continued Reverse Connector C215 – 2009-2012 (early production) F150 6509 Instructions 6-18-12 F series (1).
INSTALLATION INSTRUCTIONS Section 6B: Reference – Previous Model Year Ignition & Reverse Locations continued Ignition and Reverse Connector C264 – 2008 Super Duty 6509 Instructions 6-18-12 F series (1).
INSTALLATION INSTRUCTIONS Section 6B: Reference – Previous Model Year Ignition & Reverse Locations continued Ignition and Reverse Connector C264 – 2009-2012 (early production) Super Duty 6509 Instructions 6-18-12 F series (1).