User Manual

ManualsBrandsBrandmotion ManualsCar1009-6503

INSTALL A T ION(INSTR U C TIONS(

6503 Instructions 2-4-14.Doc Page 1 of 8

Rear Vision System – Aftermarket and Factory 8.4” Touch Screen Display

(Factory Display requires Chrysler/Dodge dealer to activate)

2013 – Current Dodge Ram (Kit part number 1009-6503)

NOTE: Raising Reverse signal voltage using a Single Pull Dual Throw Relay is required when used with aftermarket

mirrors and displays. (Please refer to detailed installation steps on Page 7 of these instructions.)

Please read thoroughly before starting installation

and check that kit contents are complete.

Items Included in the Kit:

Chassis Harness with RCA*

Tailgate Handle with Camera

8.4” Factory Touch Screen Jumper

Harness

1 bag containing:

Plug for Non-Locking Tailgates

(Optional)

Red wire with terminal for older vehicles (optional)

Black wire with terminal for older vehicles (optional)

1 bag containing:

These instructions

Template

*In some cases a RCA extension may be required

to connect to your aftermarket display; Kit#

9002-6111 may be purchased from

Brandmotion.com

Tools Required:

Socket Wrench with 7mm & 8mm Sockets

T20 and T30 Torx Bits

Phillips and Flat Blade Screwdrivers

Power Drill

1/8” Drill Bit

1” Hole Cutter

Pushpin Removal Tool

Round File or Deburring Tool

Center Punch

Utility Knife or Side Cutters

Masking Tape

Corrosion Inhibitor (recommended)

Soldering Iron & Solder (recommended)

Wire Ties (recommended)

We strive to provide accurate and up-to-date installation instructions.

For the latest full color instructions, please visit www.brandmotion.com

Install Tailgate Handle Camera

1. Set up a work area on which to set the tailgate after

removal. This area should be well protected to avoid

damage to tailgate.

2. Use your fingers to remove the black plastic filler

panel at rear of pickup bed adjacent to the license

plate. Press on the end tab and lifting outward.

Next, slide the red tab from the locked position and

unplug the tailgate power lock harness connector.

3. Unhook both tailgate support straps by inserting a

Flat Blade Screwdriver between the locking tab and

strap mount. Lift the locking tab away from the

strap mount with the screwdriver while sliding the

tailgate strap upwards. The tailgate strap hanger

can now be removed from the mount.

4. Open tailgate about ten degrees and lift right side of

the tailgate off the pin. Next, slide tailgate to the

right to remove taking care not to damage the paint.

NOTE: Tailgate removal and installation requires two

people.

Summary of content (8 pages)

PAGE 1
INSTALLATION INSTRUCTIONS Rear Vision System – Aftermarket and Factory 8.4” Touch Screen Display (Factory Display requires Chrysler/Dodge dealer to activate) 2013 – Current Dodge Ram (Kit part number 1009-6503) NOTE: Raising Reverse signal voltage using a Single Pull Dual Throw Relay is required when used with aftermarket mirrors and displays. (Please refer to detailed installation steps on Page 7 of these instructions.
PAGE 2
INSTALLATION INSTRUCTIONS 5. Remove the handle access panel inside the tailgate using a T30 Torx driver. (NOTE: If vehicle is equipped with a bed liner, the tailgate portion of the liner must be removed prior to this step.) 6. Remove nuts attaching handle to tailgate using an 8mm Socket, then remove handle from tailgate. (NOTE: Non-power locking tailgate mechanism shown.) 7. If equipped, remove the lock cylinder from existing handle. 9.
PAGE 3
INSTALLATION INSTRUCTIONS 12. Route the supplied Camera Harness through the pass-through hole in the inner brace of the tailgate. 17. RECOMMENDED: Use a Cotton Swab or small brush to apply Corrosion Inhibitor to exposed edges. 13. Route Camera Harness through the rectangular hole in the bottom of the tailgate. 18. Taking care not to damage the Camera Harness, reinstall tailgate by lifting it into place, rotating it down about ten degrees, and sliding it to the left. 14.
PAGE 4
INSTALLATION INSTRUCTIONS 26. Insert the large gray connector end of the supplied Chassis Harness through the body floor plug hole. 23. Remove rear driver’s-side sill plate by lifting it at front and working your way back with your hands. 27. Seat grommet affixed to the supplied Chassis Harness in the body floor plug hole by firmly pressing it with your fingers. 24. Lift driver’s side rear seat to expose the under seat storage compartment.
PAGE 5
INSTALLATION INSTRUCTIONS 30. Route Chassis Harness around B-pillar trim by lifting up on the trim and feeding harness through to front. Connect Chassis Harness to Vehicle Wiring 36. Connect the supplied Chassis Harness Red, Green, and Black leads as directed in the chart appropriate for your vehicle below. Chart A: Vehicles Equipped with Factory 8.4” Touch Screen 31. Continue to route Chassis Harness along the driver’s side front door opening sill area.
PAGE 6
INSTALLATION INSTRUCTIONS Figure 4 Chart B: 2013 to present Ram Aftermarket mirror/ display / Aftermarket NAV Splice Circuit 86 Relay wire to Reverse (+) signal at white/tan wire in Pin 41. Using a commonly available Single Pull Dual Throw Relay (Figure 3), splice the leads of the supplied Mirror Harness to each numbered circuit of the female relay connector as follows (Recommended: Solder and cover with Heat Shrink Tubing.
PAGE 7
!"#$%&&%$!'"(!"#$)*+$!'"#( 38. If using this kit with the factory 8.4” touch screen, follow Steps 39 through 53 and Steps 56 through 58 below. If using this kit with an aftermarket mirror / display / NAV display, connect Chassis Harness male RCA to “Camera IN” on the aftermarket mirror / display/ NAV display. NOTE: A RCA extension may be required. Proceed to Step 50. 39. Use of this camera with the factory Ram 8.4” touch screen requires activation by a Chrysler/Dodge dealer.
PAGE 8
INSTALLATION INSTRUCTIONS 55. Reassemble all previously removed parts. 56. If you connected the camera to a factory 8.4” touch screen, and the vehicle has not been reprogrammed to “enable” the camera, have a Chrysler/Dodge dealer program the vehicle as follows: 57. Start vehicle and shift into Reverse in order to check that all connections were made properly. If all of the connections are correct you will see the camera image displayed on your factory 8.4” touch screen. 58.