INSTALLATION INSTRUCTIONS Rear Vision System – Mirror Display 2009-Current Dodge Ram (Kit part number 1009-9517) Kit Contents: Chassis (longer) Harness Endgate Handle with Camera 1 bag containing: Wire Ties (Qty: 17) Bottle of ZTech (in a white bottle) Plug for Non-Locking Endgates (Optional) Inside Rear View Mirror Interior (shorter) Harness 1 bag containing: Template (along with these instructions) Tools Required: Socket Wrench Sockets 8mm, 10mm, ½in Torx Bits, T20 and T30 Flat Head Pocket Screwdrivers D
INSTALLATION INSTRUCTIONS 1. Loosen the screw that attaches the existing rear view mirror to the windshield mounting button with a T20 Torx driver. (Figure 1) Figure 1 Figure 3 2. Slide the mirror upwards and towards the rear to remove it from the windshield. 3. Open the hinged cover on back of the mirror and disconnect the existing harness connector. (Figure 2) Figure 2 1009-9000-00 9 August 2011 4.
INSTALLATION INSTRUCTIONS 6. Remove the driver’s side sun visor using a 8mm socket. (Figure 5) Figure 5 8. Remove A-Pillar bolts with a 10mm socket, and then remove the A-Pillar cover by shifting it away from the A-Pillar with your hands. (Figure 7) Figure 7 7. Remove both bolt covers on the drivers side A-Pillar using a flat head pocket screwdriver. Insert the screwdriver into the gap between the bolt cover and A-Pillar cover.
INSTALLATION INSTRUCTIONS If your vehicle IS equipped with a uConnect and/or auto-dimming mirror follow step 10. If your vehicle IS NOT equipped with uConnect and/or auto-dimming mirror, skip this step and continue on to step 11. 10. For vehicles equipped with an auto dimming mirror or an uConnect mirror, wire the supplied interior harness to the existing headliner harness using a soldering iron by following the next five steps (a, b, c, d, e) and diagrams A and B on the following two pages.
INSTALLATION INSTRUCTIONS DIAGRAM A Mirror With uConnect Pinout PIN NO UCONNECT MIRROR FUNCTION COLOR TRACER COLOR 1 MICROPHONE 1 IN (+) X DG 2 MICROPHONE IN (-) X DB 3 MICROPHONE 2 IN (+) X LB DG 8 GROUND X BK LG 9 BACKUP LAMP FEED X WT LG 10 SENSOR GROUND X OR GY 13 FUSED IGNITION RUN/START CONTROL OUTPUT X PK LG 14 AUTO DAY/NIGHT MIRROR (+) X TN OR 15 MICROPHONE FEED X DG YL 16 AUTO DAY/NIGHT MIRROR (-) X TN WT Mirror With Auto-Dimming Pinout 1009-90
INSTALLATION INSTRUCTIONS DIAGRAM B Camera, Interior, and Chassis Harness Pinout PIN NO 1 NAME Video Signal CAMERA HARNESS COLOR Yellow 2 Shield White Blue White 3 Backup Lamp Blue Green Green 4 Video Ground Brown Brown Gray/Orange 5 Power Ground Black Black Black 6 Ignition Red Red Pink 1009-9000-00 9 August 2011 6 of 18 CHASSIS HARNESS COLOR White INTERIOR HARNESS COLOR Gray/Dark Blue
INSTALLATION INSTRUCTIONS 11. Route the supplied interior harness under leading edge of the driver’s side headliner by gently separating the headliner from the windshield and tucking the interior harness into the gap with your fingers. (Figure 9) 13. Route the supplied interior harness through the A-pillar opening. (Figure 11) Figure 11 Figure 9 12. Route the supplied interior harness down the driver’s side A-Pillar and wire tie it to the existing wires using three wire ties. (Figure 10) Figure 10 14.
INSTALLATION INSTRUCTIONS 17. Reinstall the overhead console by sliding the tabs on the front of the console into the headliner then pushing the tabs on the back of the unit straight up into the headliner. 18. Reinstall the sun visor using a 8mm socket. 19. Reinstall the sun visor anchor using a T20 Torx driver. 20. Remove the front driver’s side kick panel/sill plate by lifting it at the rear and working your way forward with your hands. (Figure 13) 22.
INSTALLATION INSTRUCTIONS 23. Insert the rear connector of the supplied chassis harness into the hole in the floor pan of the under seat storage compartment. (Figure 17) 25. Route the front connector of the supplied chassis harness through the seat riser reinforcement hole. (Figure 19) Figure 19 Figure 17 24. Seat the grommet affixed to the supplied chassis harness in the hole in the floor pan of the under seat storage compartment by firmly pressing it with your fingers. (Figure 18) Figure 18 26.
INSTALLATION INSTRUCTIONS Figure 21 32. Connect the supplied chassis harness and the supplied interior harness. (Figure 23) Figure 23 28. Reinstall rear sill plate by pressing it back into place with your hands. 29. Remove drivers-side kick panel insulation pad retainers using a pushpin removal tool. Route the supplied chassis harness behind the insulation (between insulation and metal frame) then reinstall the insulation. (Figure 22) Figure 22 30.
INSTALLATION INSTRUCTIONS If your vehicle IS NOT equipped with a uConnect mirror and not equipped with an autodimming mirror follow step 34. If your vehicle IS equipped with uConnect or auto-dimming mirror, skip this step and continue on to step 35. 34. Wire the supplied interior harness to the existing instrument panel connector using a soldering iron by following the next five steps (a, b, c, d, e) and diagram C on the following three pages.
INSTALLATION INSTRUCTIONS DIAGRAM C Instrument Panel Connector Pinout 1009-9000-00 9 August 2011 12 of 18
INSTALLATION INSTRUCTIONS 35. Reinstall the end of dash cap by placing it on the end of the dashboard and firmly pressing it into place with your hands. 36. Reinstall the A-Pillar cover by sliding it into place and using a 10mm socket and bolts that were removed earlier, then reinstall the bolt covers. 37. Route the chassis harness behind the rear cab mount and out to the inside of the vehicle. Wire tie the chassis harness in between the cab and bed mount using one wire tie. (Figure 26) Figure 26 38.
INSTALLATION INSTRUCTIONS 40. Use the retention clip on the bridge connector at the end of the chassis wiring harness to attach the connector to the frame rail of the bed. Tuck the coil of excess harness above the spare tire. (Figure 28) Figure 28 43. Open the endgate about ten degrees and lift the right side of the endgate off of the pin. Then slide the endgate to the right to remove, being careful not to damage the paint. Note: The endgate removal and installation will take two people to perform. 44.
INSTALLATION INSTRUCTIONS 46. Drill a starter hole at the center punch mark. Then use a hole cutter to cut a 1” hole in the endgate. (Figures 32 & 33). Clean the rough edges using a deburring tool. Figure 34 Figure 32 Figure 35 Figure 33 47. Remove lock rod retainers by unclipping the red tabs with your fingers (Figure 34). Remove the nuts attaching the handle to the endgate using a 8mm socket, and then remove the handle from the endgate. (Figure 35) 1009-9000-00 9 August 2011 15 of 18 48.
INSTALLATION INSTRUCTIONS Figure 37 50. Reinstall the handle bolts. 51. Reinstall the linkage rods and close the red tabs around them using your fingers. (Figure 40) Figure 40 Figure 38 52. Route the supplied camera harness through the pass-through hole in the inner brace of the endgate. (Figure 41) Figure 41 49. Route the camera connector and wiring harness through the endgate and install the supplied handle using a 8mm socket and the existing hardware.
INSTALLATION INSTRUCTIONS 53. Route the wiring harness through the 1” hole that was cut using the supplied template. (Figure 42) 55. Seat the grommet affixed to the camera harness into the 1” hole by firmly pressing it with your fingers. (Figure 44) Figure 42 Figure 44 54. Apply corrosion protection (ZTech) to 1” hole that was cut using the supplied template. (Figure 43) 56. Reinstall the handle access panel on the inside of the endgate using a T30 Torx driver and the existing hardware. 57.
INSTALLATION INSTRUCTIONS 60. Plug the camera wiring harness connector into the chassis wiring harness connector. (Figure 46) Figure 46 61. Start the vehicle and put it into reverse in order to check that all connections were made properly. If all of the connections are correct you will see an image displayed on the left side of the supplied mirror.