Owner's Manual

ManualsBrandsBrandmotion ManualsCar & Vehicle ElectronicsBrandmotion 9002-8847 Jeep Wrangler Adjustable Rear Vision System for Factory Display Radios 2007-Current

INSTALLATION INSTRUCTIONS

Jeep Wrangler Adjustable Rear Vision System for Factory

Display Radios 2007-Current 9002-8847

Items Included in the Kit

Camera

Chassis Harness

Zip lock bag with 15 Wire Ties & 3 Push Nuts

These Instructions

22--pin white connector w/ video RCA

OBDII Flash module

Required Tools & Supplies

T15 & T20 Torx Bits

7mm & 10mm Sockets

Phillips Screwdriver

Plastic Trim Removal Tool

Soldering Iron, Solder, & Heat Shrink Tubing

(RECOMMENDED) or T-taps as an alternate splicing

method

Electrical Tape

Please read so you do not VOID the warranty:

If the camera harness is run through the center on the camera

bracket, it will cut the camera harness. This will void the

warranty on the camera.

9002-8847 Instructions 9-17-2019 Page 1 of 6 DM

Summary of content (6 pages)

PAGE 1
INSTALLATION INSTRUCTIONS Jeep Wrangler Adjustable Rear Vision System for Factory Display Radios 2007-Current 9002-8847 Items Included in the Kit Required Tools & Supplies Camera Chassis Harness Zip lock bag with 15 Wire Ties & 3 Push Nuts These Instructions 22--pin white connector w/ video RCA OBDII Flash module T15 & T20 Torx Bits 7mm & 10mm Sockets Phillips Screwdriver Plastic Trim Removal Tool Soldering Iron, Solder, & Heat Shrink Tubing (RECOMMENDED) or T-taps as an alternate splicing method Electr
PAGE 2
INSTALLATION INSTRUCTIONS Camera Power Instructions!: Only ONE of the red wires should be connected to ignition 12v+. The other should be isolated with electrical tape before powering camera up. See step 26. Camera Installation 1. Loosen lug nuts to remove the spare tire. Adjustment Bracket for Camera Clearance using Phillips Screwdriver and 3/8” Wrench or Socket Drive 2. Slide Camera on studs placing harness end inside of tire carrier. Do not run harness through the camera bracket opening. 3.
PAGE 3
INSTALLATION INSTRUCTIONS 5. Plug the Camera connector into the Chassis Harness connector, and insert RCA connector end of supplied Chassis Harness through the rear gate vent behind tire carrier. 8. Use supplied Wire Ties to secure Chassis Harness to existing harness. 6. Using a plastic trim removal tool, remove interior panels on the inside of the rear gate. 9. Use supplied Wire Ties to secure Chassis Harness to fabric factory wire cover. CAUTION: Leave enough slack to allow the gate to open fully. 10.
PAGE 4
INSTALLATION INSTRUCTIONS 15. Run Chassis Harness under B-pillar cover to passenger door sill. Use a plastic trim removal tool to remove the (2) plastic push pins and remove passenger sill plate/kick panel. 16. Remove rubber bin insert from top of the dash. 11. Using a plastic trim removal tool, pry off rear seat belt closeout. 12. Using a plastic trim removal tool, remove rear access panel to expose 10mm bolt, and remove bolt. 17. Remove 7mm bolt. 13.
PAGE 5
INSTALLATION INSTRUCTIONS 19. Disconnect harness from window switches. 22. Remove (2) 7mm bolts on both sides of the steering column. 20. Remove 7mm bolt. 23. Remove center stack/cluster surround. 24. Remove glove box for access and run Chassis Harness toward the center of the dash. 21. Remove driver's knee bolster cover.
PAGE 6
INSTALLATION INSTRUCTIONS 25. Using a plastic trim removal tool, remove HVAC panel. 26. Connecting Power Splice Red power wire at the RCA to 12v+ wire at power point on center console OR splice red wire at chassis harness connector to 12v+ in the back of the vehicle. C OVER UNUSED RED WIRE. Splice Black Ground to chassis ground. RECOMMENDED: Use solder and cover with heat shrink tubing or use T-taps as an alternate connection method. 27.