Brochure
Table Of Contents
- Table of Contents
- 1/4 Turn Supply Stops
- Multi-Turn Supply Stops
- Dual Outlet Supply Stops
- Dual Outlet, Dual Shut-Off Supply Stops
- Needle & Humidifier Valves
- Water Supply Connectors
- One-Piece Water Supplies
- Supply Kits
- Water Connectors
- Installation Kits
- Water Heater Connectors
- Brass Fittings
- Waste Connectors
- Component Parts
- Water Supply Accessories
- Special Finish Water Supplies
- Special Finish Water Supplies
- Special Finish - 1/4 Turn Ball Supply Stops
- Special Finish - Multi-Turn Supply Stops
- Special Finish - Risers
- Special Finish - Supply Kits - Faucet & Toilet
- Special Finish - Component Parts & Escutcheons
- Special Finish - Cover Tubes & Pipe Nipples
- Special Finish - P-Traps & Box Escutcheons
- Special Finish - Kitchen Accessories
- Special Finish - Bath Accessories
- Finish Index
- Specifications
- Index
27
www.brasscraft.com
MULTI-TURN SUPPLY STOPS
∆
CPVC Solvent Weld x Compression - Straight
PR14X C 026613138640 1/2" Nom CPVC x 3/8" OD Comp Chrome 60 16.5
PR14X C1 026613136011 1/2" Nom CPVC x 3/8" OD Comp Chrome 24 6.8
PR14X R 026613142388 1/2" Nom CPVC x 3/8" OD Comp Rough 60 16.5
PR34X C 026613153629 1/2" Nom CPVC x 1/2" OD Comp Chrome 60 17.8
PR34X R 026613153636 1/2" Nom CPVC x 1/2" OD Comp Rough 60 17.8
MULTI-TURN SUPPLY STOPS
PART NO. UPC DESCRIPTION FINISH QTY LBS
NOTE: All 3/8" OD PEX Risers come with plastic compression sleeve.
All 1/2" OD PEX Risers come with stainless steel tube insert.
PEX Tube Compression Connection
For PEX Tube 3/8" OD and smaller, use plastic
compression sleeve.
For PEX Tube larger than 3/8" OD, use brass compression sleeve
with stainless steel tube insert.
FITTING
PLASTIC COMPRESSION SLEEVE
NUT
PEX TUBE
FITTING STAINLESS
STEEL INSERT
BRASS COMPRESSION SLEEVE
NUT
PEX TUBE
Compression Inlet
Brass Compression Nut
Brass Sleeve
Compression Outlet
Brass Compression Nut
Brass Sleeve
Handle
Zinc Die cast, Plated; ABS,
Plated; or Polycarbonate
Screw; Steel, Zinc Plated
Stem & Bonnet
Rubber Bib Washer
P.O.M. or Brass Stem
Plastic or Brass Thrust Washer
Rubber Bonnet Packing
Brass Bonnet Nut
Solid Brass
Stop Body
Anatomy Of A BrassCraft Supply Stop
Lock Shield
Loose Key
Add Prefix “S”
Lock Shield
Screwdriver Slot
Add Prefix “SS”
Stuffing Box
Lock Shield
Loose Key
Add Prefix “ST”
Stuffing Box
Lock Shield
Screwdriver Slot
Add Prefix “SST”
Cross Handle
Add Prefix “X”
Round (Brass) Handle
Add Prefix “XX”
Stuffing Box
Add Prefix “T”
Sweat and loose key stops are
furnished with brass stems.
All others are furnished with
corrosion resistant P.O.M. stems.
Brass Stem (Non-Sweat)
Add Suffix “Z” e.g., OCR19Z C
Variations
See page 112 for Available Variations
∆ CPVC pre-torqued ttings eliminate the need for tightening on the job.