Product Manual

ManualsBrandsBravePro ManualsGasBrave Pro - 259 GPM (3") Semi-Trash Water Pump w/ Honda GX Engine

Series BRP160SP2, BRP160SP3 & BRP200TP3

Gas Engine-Driven, Self-Priming, SAE Mount,

BRAVE PRO Centrifugal Pumps

MBRP160SP2

Rev. A

Installation, Operation, Repair and Parts Manual

BRAVE PRO Self-Priming Centrifugal Pumps handle big, high-capacity, liquid transfer jobs with ease. Use them for transferring

water, liquid fertilizers, and other chemicals compatible with pump materials. Make short work of other farm jobs: filling nurse

tanks, watering seedbeds and transferring liquids. This self-priming model makes it ideal for de-watering applications.

BRP160SP2

Close-Coupled, Gas Engine-Driven

Self-Priming Centrifugal Pump

BRP160SP3

Close-Coupled, Gas Engine-Driven

Self-Priming Centrifugal Pump

BRP200TP3

Close-Coupled, Gas Engine-Driven

Self-Priming Centrifugal Trash Pump

Description

California Proposition 65 Warning – This product and related accessories contain chemicals known to the State of California

to cause cancer, birth defects or other reproductive harm.

WARNING: Do not pump flammable or explosive fluids such

as gasoline, fuel oil, kerosene, etc. Do not use in explosive

atmospheres. The pump should be used only with liquids

that are compatible with the pump component materials.

Failure to follow this warning can result in personal injury

and/or property damage and will void the product warranty.

1. DO NOT EXCEED recommended speed, pressure and

temperature (140° F) for pump and equipment being used.

2. BEFORE SERVICING, drain all liquids from the system and

flush. Remove the spark plug wire from the spark plug

before servicing the pump or engine.

3. Secure the discharge lines before starting the pump. An

unsecured line may whip, causing personal injury and/or

property damage.

4. Check hose for weak or worn condition before each use.

Make certain that all connections are tight and secure.

5. Periodically inspect the pump and the system components.

Perform routine maintenance as required

(see Maintenance section).

6. Protect pump from freezing conditions by draining liquid

and pumping a permanent-type automobile antifreeze

containing a rust inhibitor through the system, coating the

pump interior. A 50% mixture with water is recommended.

7. Do not operate a gasoline engine in an enclosed area.

Be sure the area is well ventilated.

WARNING: Gasoline is a highly combustible fuel. The

improper use, handling, or storage of gasoline can be

dangerous. Never touch or fill a hot engine.

8. Use only pipe, hose and fittings rated for the maximum psi

rating of the pump.

9. Do not use these pumps for pumping water or other liquids

for human or animal consumption.

Max. Flow Rate: .................................. 147 GPM

Max. Pressure: ..................................... 50 PSI

Max. Total Head: .................................... 115 Ft

Max. Suction Li: ..................................... 28 Ft

Ports: ........................................... 2" NPT Inlet

2" NPT Outlet

Engine: ..................................... Honda GX160

Max. Flow Rate: .................................. 259 GPM

Max. Pressure: ..................................... 50 PSI

Max. Total Head: .................................... 100 Ft

Max. Suction Li: ..................................... 28 Ft

Ports: ........................................... 3" NPT Inlet

3" NPT Outlet

Engine: ..................................... Honda GX160

Max. Flow Rate: ...................................... 272 GPM

Max. Pressure: .......................................... 50 PSI

Max. Total Head: ........................................ 115 Ft

Max. Suction Li: ........................................ 28 Ft

Ports: ................................................. 3" NPT Inlet

3" NPT Outlet

Engine: ............................................ Honda GX200

General Safety Information

Summary of content (8 pages)

PAGE 1
Series BRP160SP2, BRP160SP3 & BRP200TP3 Gas Engine-Driven, Self-Priming, SAE Mount, BRAVE PRO Centrifugal Pumps MBRP160SP2 Rev. A Installation, Operation, Repair and Parts Manual Description BRAVE PRO Self-Priming Centrifugal Pumps handle big, high-capacity, liquid transfer jobs with ease. Use them for transferring water, liquid fertilizers, and other chemicals compatible with pump materials. Make short work of other farm jobs: filling nurse tanks, watering seedbeds and transferring liquids.
PAGE 2
Hazardous Substance Alert Please Note: It is illegal to ship or transport any hazardous chemicals without United States Environmental Protection Agency Licensing. 2. Before returning unit for repair, drain out all liquids and flush unit with neutralizing liquid. Then, drain the pump. Attach a tag or include a written notice certifying that this has been done. 3. Never store pumps containing a hazardous chemical. 1. Always drain and flush pumps before servicing or disassembling for any reason.
PAGE 3
Operation and Maintenance (Operation and Maintenance Continued) Stopping the Pump chemically neutralize the liquid pumped. Mix according to the manufacturer’s directions. This will dissolve most residues remaining in the pump, leaving the inside of the pump clean and ready for use. 1. Stop pump for a short time: Run engine throttled all the way down (fully to the right). Turn engine switch to OFF position. 2.
PAGE 4
Repair Instructions (Repair Instructions Continued) Clean-up of Pump Housing 6. It is now necessary to check the clearance between the impeller and volute. As shown in the sketch below, measure the inside depth of the volute case (distance A). Then measure the distance from the casing cover to the front edge of the impeller (distance B). The difference between the two measurements should be between 0.024 and 0.036” or about 1/32” clearance.
PAGE 5
Troubleshooting Symptom Probable Cause(s) No discharge Corrective Action(s) Discharge line must be open for priming to occur. If valve is installed, check that it is open. Pump not priming Fill priming chamber with water. Increase engine speed. Air leaks in suction line Check inlet fittings for leaks. Seal leaks. Undersized or collapsed suction hose Suction inlet hose should be same diameter as inlet port fitting.
PAGE 6
Models BRP160SP2, BRP160SP3 1 2 3 4 5 6 7 11 10 8 9 12 13 14 IMPORTANT: When ordering parts, give PART NUMBER and PART DESCRIPTION. Reference Numbers are used ONLY to point out parts in the drawing and are NOT to be used as ordering numbers. 15 16 17 11 18 13 14 11 18 19 20 STANDARD SEAL KIT NO. 3430-0799 Consists of (1) Ref. 2 O-ring, (4) Reg. 3 Sealed Washers, (1) Ref. 5 Mechanical Seal, (1) Ref. 8 O-ring, (1) Ref. 10 Outlet Sealed Washer, (2) Ref. 13 O-rings, and (1) Ref.
PAGE 7
Models BRP200TP3 12 11 10 IMPORTANT: When ordering parts, give PART NUMBER and PART DESCRIPTION. Reference Numbers are used ONLY to point out parts in the drawing and are NOT to be used as ordering numbers. 3 2 9 8 7 13 6 1 5 2 4 3 14 15 STANDARD SEAL KIT NO. 3430-0801 Consists of (2) Ref. 2 O-ring, (1) Ref. 6 Check Valve, (1) Ref. 10 O-ring, (1) Ref. 11 O-ring, and (1) Ref. 13 Silicon Carbide Mechanical Seal Parts List: BRP200TP3 Ref. No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Qty. Req’d.
PAGE 8
Limited Warranty on Brave Agricultural Pumps & Accessories Brave agricultural products are warranted to be free of defects in material and workmanship under normal use for the time periods listed below, with proof of purchase. - Pumps: one (1) year from the date of manufacture, or one (1) year of use. This limited warranty will not exceed two (2) years, in any event. - Accessories: ninety (90) days of use.