INTRODUCTION You are now the owner of a Brave Pro TRENCHER. The Brave Pro TRENCHERS are very versatile trenchers which, when properly equipped, will trench in almost any soil condition. The Brave Pro TRENCHER is an inexpensive alternative to the much heavier, more bulky and less maneuverable trenchers on the market. If you have any questions or problems with your Brave Pro TRENCHER, please contact your dealer or distributor.
warranty statement statement OF POLICy In accordance with our established policy of constant improvement, we reserve the right to amend these specifications at any time without notice. enGIne warranty Warranty of all engines and engine parts Is the sole responsibility of the particular engine manufacturer. See engine warranty in the engine manual. Engine problems must be checked and approved for warranty by an authorized engine manufacturers service center. The mfg.
Brave Product Registration Form YOUR INFORMATION Full Name: Last First M.I. Address: Street Address Apartment/Unit # City State ZIP Code Alternate Phone: Home Phone: Email PURCHASED FROM Company: Address: Street Address Apartment/Unit # City State ZIP Code MODEL INFORMATION Purchase Date Application Type Model (i.e. BRPT704H) ප ,ŽŵĞŽǁŶĞƌ ප ŽŵŵĞƌĐŝĂů ප ZĞŶƚĂů Serial # (i.e. 123456) Signature Register your product online at www.braveproducts.
table of contents 1. Getting Acquainted With Your Brave Pro Trencher .....................1-1 2. Safety Precautions ......................................................................2-1 3. Operating Instructions.................................................................3-1 4. Scheduled Maintenance..............................................................4-1 5. Trouble Shooting .........................................................................5-1 6.
GettInG aCqUaInteD wIth yOUr Brave PrO trenCher
DO NOT assemble the Brave Pro Trencher before reading assembly instructions. DO NOT start the Brave Pro Trencher before reading operating instructions & engine operator/owner manual. DO NOT modify the Brave Pro Trencher in any way. DO NOT operate without all shields in place. DO NOT operate without eye protection. Goggles are provided with each Brave Pro Trencher. DO NOT lift trencher off the ground until engine is switched off and rotor has stopped.
Brave PrO trenCher
Brave PrO BrPt704h (See equipping your Brave Pro Trencher for varying conditions, Page 6-1.) Check set screws in pulleys & lock collars for tightness. the BRPT704H i. If your Brave Pro Trencher is equipped with a rock rotor, the points engine as needed. .
Brave Pro Trencher. your trencher is equipped with the rock rotor. If it has the rock rotor, then on handlebar, front to rear, alternately.
When installing points on rock rotors, the points must be loose and free to rotate to
life from your BRAVE PRO TRENCHER. Most required maintenance procedures are 7” model when clutch lever is engaged. Keep belt free of dirt and grease at all times. Check at least every 200 feet initially. When working in difficult soil conditions, they the bolt is loose, the idler arm may have enough lateral movement to cause the belts to come off the pulley. The pivot bolt should be tight enough to prevent lateral movement, but not so tight that it restricts free pivoting of the idler arm.
eqUIPPInG yOUr Brave PrO trenCher FOr varyInG COnDItIOns BRAVE PRO TRENCHER to Choose the smallest trench that is practical for the job. Digging a smaller trench will save you time and money in three ways: a. You will be able to trench faster b. You will have less soil to clean up. c. Your digging rotors will last longer. 5.
Brave PrO trenCher mODeL BrPt704h assemBLy InstrUCtIOns Turn the nut to the right to tighten. This nut does not need to be put on extremely tight. Tighten to about 100 foot pounds of torque or hand tighten with the Rotor Nut Wrench and Handle (Provided w/ Brave Pro Trencher). CAUTION!! If using an impact wrench, do not over tighten because it may be very difficult to loosen the nut to change rotors.
BRPT704H (BRPT704H only) 51 17
BrPt704h trenCher Clay hood Parts Drawings Brpt704h hood assemBly 37 7-3
Brave PrO mODeL BrPt704h Parts List reF. nO. 1 2 3 5 6 8 9 10 11 13 14 15 16 17 18 19 20 22 23 24 25 26 26A 27 28 29 30 31 34 37 38 40 41 42 43 44 45 46 47 48 49 50 51 Part nO.
rotor Compatibility list “X” INDICATES ROTOR WILL FIT ON BRPT704H TRENCHER trencher Brpt704h clay rotors Part # Depth X Width 702-81 3” X 1” 2 POINTS X 702-82 4” X 1” 2 POINTS X 702-82A 5” X 1” 2 POINTS X 702-87 7” X 1” 2 POINTS X 702-130 3” X 2” 3 POINTS X 702-131 4” X 2” 3 POINTS X 702-132 5” X 2” 3 POINTS X 702-133 7” X 2” 3 POINTS X 702-134 7” X 13/8” 3 POINTS X 702-135 5” X 13/8” 2 POINTS X 702-89 4” BEDMASTER ROTOR X 702-93 3” BEDMASTER ROTOR X 702-9