FEED MIXER 524-15B ASSEMBLY, OPERATION AND PARTS MANUAL ROTO-MIX P.O. BOX 1724 3305 E. Wyatt Earp Blvd.
524-15 TABLE OF CONTENTS PAGE NO.
WARRANTY ROTO-MIX LLC, warrants to the original purchaser all products manufactured by it to be free from defects in material and workmanship under normal use and service.
SCALES WARRANTY & SERVICE POLICY DIGI-STAR SCALE SYSTEMS Digi-Star, LLC warrants for a period of one year from date of installation, to correct by repair or replacement, at Digi-Star’s option, any defect in material or workmanship in any part of this product. In the event of replacement, Digi-Star’s sole obligation shall be to provide replacement products or parts. F.O.B. Fort Atkinson, Wisconsin.
OPERATOR QUALIFICATIONS Operation Of this mixer/feeder shall be limited to competent and experienced persons. In addition, anyone who will operate or work around a mixer/feeder must use good common sense. In order to be qualified, he or she must also know and meet all other qualifications, such as: 1. Some regulations specify that no one under the age of sixteen (16) may operate power machinery. It is your responsibility to know what these regulations are in your area and/or situation. 2.
SAFETY TAKE NOTE! THIS SAFETY ALERT SYMBOL FOUND THROUGHOUT THIS MANUAL IS USED TO CALL YOUR ATTENTION TO INSTRUCTIONS INVOLVING YOUR PERSONAL SAFETY AND THE SAFETY OF OTHERS. FAILURE TO FOLLOW THESE INSTRUCTIONS CAN RESULT IN INJURY OR DEATH. THIS SYMBOL MEANS -ATTENTION! -BECOME ALERT! -YOUR SAFETY IS INVOLVED! SIGNAL WORDS: Note the use of the signal words DANGER, WARNING, and CAUTION with the safety messages.
SAFETY FIRST REMEMBER: The careful operator is the best operator. Most accidents are caused by human error. Certain precautions must be observed to prevent the possibility of injury or death. DO NOT ALLOW PERSONNEL OTHER THAN THE QUALIFIED OPERATOR NEAR THE MACHINE. NEVER START MACHINE UNTIL ALL GUARDS AND SAFETY SHIELDS ARE IN PLACE. DO NOT CLEAN, ADJUST OR LUBRICATE THE MACHINE WHILE IT IS IN MOTION. BEFORE STARTING TRACTOR ENGINE, BE SURE PTO SHIELDS TURN FREELY.
SAFETY READ BEFORE YOU FEED EQUIPMENT SAFETY GUIDELINES Safety of the operator is one of the main concerns in designing and developing a new piece of equipment. Designers and manufactures build in as many safety features as possible. However, every year many accidents occur which could have been avoided by a few seconds of thought and a more careful approach to handling equipment. You, the operator, can avoid many accidents by observing the following precautions in this section.
SAFETY READ BEFORE YOU FEED KEEP ALL SHIELDS IN PLACE Do not operate mixer/feeder without safety shields in place. Rotating parts can crush or dismember causing personal injury or death. Disconnect PTO driveline before removing shields for adjustment or service. OPERATE MIXER/FEEDER SAFELY Rotating parts can entangle or strike people, resulting in personal injury or death. Never enter a mixer/feeder while in operation. Operate the mixer/feeder from the operator’s seat only.
SAFETY READ BEFORE YOU FEED STAY CLEAR OF ROTATING DRIVELINES Entanglement in rotating driveline can cause serious injury or death. Keep tractor master shield and driveline shields in place at all times. Make sure rotating shields turn freely. Wear close fitting clothing. Stop the engine and be sure PTO driveline is stopped before making adjustments, connections, or cleaning out PTO driven equipment . PREVENT BATTERY EXPLOSIONS Keep sparks, lighted matches, and open flame away from the top of battery.
SAFETY READ BEFORE YOU FEED PREPARING TRACTOR FOR TRAILER MIXER POSITIONING DRAWBAR IMPORTANT: Drive components can be damaged from excessive speed. Under no circumstances should a feed mixer equipped with 540 RPM be operated by a tractor with 1000 RPM PTO. Feed mixers are available with either 540 or 1000 RPM driveline. Match tractor PTO with the feed mixer driveline. IMPORTANT: To prevent driveline damage, adjust tractor drawbar to recommended setting. Disengage tractor PTO before turning.
SAFETY SIGNS 12
SAFETY SIGNS 13
SAFETY SIGNS 14
SAFETY READ BEFORE YOU FEED SAFETY DECAL CARE Keep safety decals and signs clean and legible at all times. Replace safety decals and signs that are missing or have become illegible. Replaced parts that displayed a safety sign should also display the current sign. Safety decals or signs are available from your dealer or the ROTO-MIX manufacturing plant. How to Install Safety Decals: Be sure that the installation area is clean and dry. Decide on the exact position before you remove the backing paper.
SAFETY READ BEFORE YOU FEED REMEMBER Your best assurance against accidents is a careful and responsible operator. If there is any portion of this manual or function you do not understand, contact your dealer or the ROTO-MIX plant. BEFORE OPERATION: Carefully study and understand this manual. Do not wear loose-fitting clothing which may catch in moving parts. Always wear protective clothing and substantial shoes. Keep wheel lug nuts or bolts tightened to specified torque.
SAFETY READ BEFORE YOU FEED DURING OPERATION: Beware of bystanders, particularly children! Always look around to make sure that it is safe to start the engine of the towing vehicle or move the unit. This is particularly important with higher noise levels and quiet cabs, as you may not hear people shouting. NO PASSENGERS ALLOWED - Do not carry passengers anywhere on, or in, the tractor or equipment, except as required for operation. Keep hands and clothing clear of moving parts.
SAFETY READ BEFORE YOU FEED DURING OPERATION (CONT.) Never leave running mixer/feeder unattended. As a precaution, always recheck the hardware on mixer/feeder following every 100 hours of operation. Correct all problems. Follow the maintenance safety procedures. FOLLOWING OPERATION: Following operation, or when unhitching, stop the tractor or towing vehicle, set the brakes, disengage the PTO and all power drives, shut off the engine and remove the ignition keys.
SAFETY READ BEFORE YOU FEED HIGHWAY AND TRANSPORT OPERATIONS (CONT.): Comply with state and local laws governing highway safety and movement of farm machinery on public roads. Use approved accessory lighting flags and necessary warning devices to protect operators of other vehicles on the highway during daylight and nighttime transport. The use of flashing amber lights is acceptable in most localities. However, some localities prohibit their use.
SAFETY READ BEFORE YOU FEED PERFORMING MAINTENANCE (CONT.): Always use the proper tools or equipment for the job at hand. Use extreme caution when making adjustments. Never use our hands to locate hydraulic leaks on attachments. Use a small piece of cardboard or wood. Hydraulic fluid escaping under pressure can penetrate the skin. When disconnecting hydraulic lines, shut off hydraulic supply and relieve all hydraulic pressure.
READ THE FOLLOWING BEFORE WELDING ON THIS MIXER/FEEDER When welding on your mixer/feeder, do not allow the current to flow through the ball bearings or the roller chains. Ground directly to the item being welded. Always disconnect the scale instrumentation from the weigh bars or load cells and the power source. Be sure the current does not pass through weigh bars or load cells or scale indicator. The alternator should always be disconnected if the mixer/feeder is not disconnected from the towing vehicle.
OPERATION: Trailer mounted mixers can be furnished with single tractor controls or dual controls. Dual controls are standard unless specified. 1. Single controls operate as follows: Spout goes down first - door opens second. Door closes first - spout goes up second. 2. The disadvantage of the single control is that it does not let you adjust the spout height without first closing the door. ROTO-HAY PROCESSOR The ROTO-HAY PROCESSOR is designed for processing hay into the mixer.
LOADING INSTRUCTIONS FOR HAY PROCESSOR Load all commodities except liquids on the discharge (auger) side with the hay pan in the raised position. The raised hay pan does not affect the mixing action 1. If molasses and/or liquid protein is used, load on the rotor side of the mixer first with the mixer not running. 2. Load one (1) grain or dry commodity in a minimum amount equal to the amount of hay to be put into mixer with the mixer not running. 3.
LUBRICATION CHART DISENGAGE PTO & SHUT OFF POWER BEFORE LUBRICATING THE MACHINE. LOOSE OR FLOPPY CLOTHING SHOULD NOT BE WORN BY THE OPERATOR. OIL BATH: Fill the oil bath with 30 weight motor oil to sight plug level. GREASE BANK: Grease every 100 hours. FRONT END BEARINGS: Grease every 100 hours. INPUT BEARINGS: One (1) on input shaft beneath mixer/feeder. Grease every 100 hours. PTO SHAFTS & U-JOINTS: Grease every 10 to 20 hours.
524-15 SPECIFICATIONS Capacity (Cu. ft.) .......................................... 520 Struck level capacity (Cu. ft.) ....................... 560 Top Auger Bearing (Front) ........................... 2-3/16” 4-Bolt Top Auger Bearing (Rear)............................ 3” 4-Bolt Bottom Auger Bearing (Front)...................... 2-7/16” 4-Bolt Bottom Auger Bearing (Rear) ...................... 3-1/2” 4-Bolt Rotor Bearing (Front) ................................... 2-15/16” 4-Bolt Rotor Bearing (Rear).......
PTO CHART 524-15 PTO (% ENGINE SPEED) GEARBOX (RATIO) INPUT SPROCKET JACKSHAFT SPROCKET 80-85 250 FT./LB MIN. Engine Rotation 3:1 25 Tooth 17 Tooth 48 Tooth DIESEL AUTO TRANS FOR OTHER ENGINE OR TRANSMISISSION APPLICATIONS CONSULT FACTORY 1000 TRACTOR DRIVE (OPTIONAL) 15 Tooth 48 Tooth 540 TRACTOR DRIVE (STANDARD) STATIONARY 15 Tooth 25 Tooth 17 Tooth 48 Tooth BELT RATIO 30 HP 5V-2 Groove 16” & 5V-3 Groove 9.25” 2 Belts 5V-1060 25HP 5V-2 Groove 16” & 5V-3 Groove 9.
524-15 TRUCK DIMENSIONS HEIGHT DIMENSIONS BASED ON 38” TRUCK FRAME WITH 20” SPOUT STANDARD 108" (SPOUT CLOSED) 106" 101 1/2" APPROXIMATE WEIGHT 524-15 ON TRUCK ................ 10,800 LB. WITH HAY PROCESSOR ..... 11,550 LB.
524-15 TRAILER DIMENSIONS 110" (SPOUT CLOSED) 106" 99" HEIGHT DIMENSIONS ARE BASED ON 44” O.D. TIRES 17” SPOUT STANDARD 49" OPTIONAL HAY PROSESSOR 18" APPROXIMATE WEIGHT 524-15 ON TRAILER ......... 12,500 lbs W/HAY PROCESSOR........ 13,250 lbs *INCREASE DIMENSIONS BY 4” WHEN OPTIONAL RISER BLOCKS ARE INSTALLED.
524-15 TRAILER DIMENSIONS (WITH CONVEYOR) 126" 124 1/4" 122 1/2" 106" 7" OPTIONAL HAY PROCESSOR 49" 18" 24" CONVEYOR 36" CONVEYOR 48" CONVEYOR 36" CL 44" 44" 40" 48" 54" 35 1/2" 59 1/2" 47" to 51" 94" to 102" 33" - 35" 43 1/4" - 45 1/4" 53 1/2" - 55 1/2" NOTE: UNDERLINED DIMENSIONS ARE WITH CONVEYOR SET AT ITS MAXIMUM OPERATING ANGLE OF 30 DEGREES All Dimensions & Specifications are Approximate and Subject to Change Without Notice 29
524-15 STATIONARY DIMENSIONS 106" 4 1/2" 52" OPTIONAL HAY PROCESSOR APPROXIMATE WEIGHT, LESS MOTOR 524-15 STATIONARY.................... 10,500 LB. WITH HAY PROCESSOR.............. 11,250 LB.
524-15 MOUNTING DIMENSIONS All Dimensions & Specifications are Approximate and Subject to Change Without Notice 31
524-15 MOUNTING DIMENSIONS All Dimensions & Specifications are Approximate and Subject to Change Without Notice 32
PARTS PAGES TABLE OF CONTENTS PAGE NO. WIRING SCHEMATIC FOR STRAIGHT DOOR ............................................................ 34 JOYSTICK ASSEMBLY ....................................................................................................... 35 MV5 DOUBLE HYDRAULIC VALVE ASSEMBLY ........................................................ 36 12V DOUBLE HYDRAULIC VALVE ASSEMBLY .......................................................... 37 HYDRAILIC PUMP, TRUCK .................................
WIRING SCHEMATIC FOR STRAIGHT DOOR YELLOW RED 3 GREEN 1 BROWN RED 2 YELLOW GREEN BROWN REF. NO 1 A B 2 3 PART NO. 780080 780081 781055 780123 DESCRIPTION QTY. PUSH BUTTON SWITCH PANEL JOYSTICK PANEL ........................................................... 1 TRUCK TO MIXER WIRE ASSEMBLY ............................ 1 HYDRAULIC CONTROL VALVE......................................
JOYSTICK ASSEMBLY BOTTOM TOP TO 12 VOLT 3 BROWN 2 RED YELLOW BROWN RED GREEN YELLOW GREEN 1 REF. NO 1 2 3 PART NO. 781056 185575 357705 DESCRIPTION QTY. SWITCH WIRE ASSEMBLY ................................................... 1 JOYSTICK BRACKET ............................................................. 1 JOYSTICK SWITCH.................................................................
MV5 DOUBLE HYDRAULIC ASSEMBLY (780123 OLD STYLE) OUTLET 1 1A 2 3 INLET REF. NO 1 1A 2 3 PART NO. 362209 362206 368030 368115 BUILT IN PRESSURE RELIEF PRESET TO 1500 PSI DESCRIPTION QTY. HYDRAULIC VALVE 12V DOUBLE ................................. 1 12V SING MV5 HYD VLV MVSR 1500-10-50-12-TD....... 2 FITTING, 9/16”MOR x 3/8” FPSW 90° ............................. 4 FITTING, 9/16” MOR x 3/8” FPSW STRT ........................
12V DOUBLE HYDRAULIC ASSEMBLY (780123 NEW STYLE) 1 3 2 4 5 DO NOT USE THIS POLE TO JOYSTICK TO JOYSTICK DO NOT USE THIS POLE 5 2 4 3 REF. NO 1 2 3 4 5 PART NO. 362209 368115 368024 368030 781057 DESCRIPTION QTY. HYDRAULIC VALVE 12V DOUBLE..................................1 FITTING, 9/16” MOR x 3/8” FPS.......................................2 FITTING, 45° SWIVEL 9/16” MOR x 3/8” FPS..................2 FITTING, 90° SWIVEL 9/16” MOR x 3/8” FPS..................2 SOLENOID GROUND WIRE, 12 VOLT .....
HYDRAULIC PUMP, TRUCK (780064) 7 6 5 4 3 1 2 REF. NO 1 2 3 4 5 6 7 PART NO. 336008 324040 189053 362017 368050 368512 368040 DESCRIPTION QTY. BUSHING, SH1/2” QD...................................................... 1 SHEAVE, 1B 4.0” V-BELT ................................................ 1 HYDRAULIC PUMP BRACKET........................................ 1 HYDRAULIC PUMP (D17AA2A) ...................................... 1 FITTING, 7/8” MOR x 3/4” FPSW 90° ..............................
OIL RESERVOIR ASSEMBLY (780205) 1 2 4 3 5 6 7 REF. NO 1 2 3 A B 4 5 6 7 PART NO. 362550 870477 352400 362403 352440 362504 368512 368665 781059 DESCRIPTION QTY. FILLER CAP......................................................................1 OIL RESERVOIR WELDMENT.........................................1 OIL FILTER ASSEMBLY...................................................1 FILTER HEAD FILTER ELEMENT SUCTION SCREEN ..........................................................
HYDRAULIC SCHEMATIC FOR STRAIGHT DOOR 2 NOTE (C) NOTE (A) 5 9 NOTE (B) 1 10 7 8 4 NOTE (D) 6 3 NOTE A: CONNECT TO SPOUT CYLINDER BASE NOTE B: CONNECT TO SPOUT CYLINDER ROD END NOTE C: CONNECT TO DOOR CYLINDER BASE NOTE D: CONNECT TO DOOR CYLINDER ROD END REF. NO PART NO. 1 2 3 4 5 6 7 8 9 10 780064 780205 780123 781059 184291 781073 781066 781069 781061 781098 DESCRIPTION QTY. HYDRAULIC PUMP ASSEMBLY ............................................. 1 RESERVOIR ASSEMBLY .......................
STATIONARY HYDRAULIC ASSEMBLY 1D 15 14 4 1A 1B 13 1E 16 1C 16 8 7 2 6 3 5 9 REF. NO PART NO. 1 781004 352205 368030 368115 357700 453717 781113 872138 781005 410852 185488 410008 872136 412416 324040 336008 325060 189088 781075 781077 781099 A B C D E 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 DESCRIPTION 11 10 12 QTY. HYDRAULIC VALVE ASSEMBLY............................................ 1 SINGLE HYDRAULIC VALVE, 120V .......................................
524-15 DISCHARGE DOOR ASSEMBLY 6 5 2 4 10 7 3 1 8 REF. NO 1 2 3 4 5 6 7 8 A B C 9 10 7 PART NO. 850140 850138 150049 404351 404003 402512 184267 780109 364055 364954 364400 184259 150385 9 DESCRIPTION QTY. DISCHARGE DOOR WELDMENT................................... 1 DOOR LEVER ARM WELDMENT ................................... 1 DOOR ARM...................................................................... 2 CLEVIS PIN 3/4” X 2-1/2”.................................................
524-15 HAND WHEEL ASSEMBLY 11 1 2 13 4 9 6 7 12 11 10 3 5 REF. NO PART NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 850079 850145 872030 872349 189105 189106 407047 410305 189112 150387 340216 150244 185114 8 DESCRIPTION QTY. HAND WHEEL FRAME WELDMENT................................... 1 524 STATIONARY DOOR WELDMENT ............................... 1 HAND WHEEL WELDMENT.................................................. 1 BEARING BRAKE MOUNT WELDMENT ............................
17” SPOUT ASSEMBLY #750044 ..............................17” SPOUT ASSY WITH MAGNET #750045 ..............................17” SPOUT ASSY NO MAGNET 4 2 5 8 5A 7 6 1A 1B 3 REF. NO PART NO. 1A 1B 2 3 4 5 5A 5B 6 7 8 850106 850107 150383 183152 850050 750019 400712 850053 400205 402005 407021 DESCRIPTION 5B QTY. 17” SPOUT WELDMENT WITH MAGNET ............................... 1 17” SPOUT WELDMENT NO MAGNET................................... 1 SPOUT PIVOT TUBE ........................................
20” SPOUT ASSEMBLY #750054 ..............................20” SPOUT ASSY WITH MAGNET #750055 ..............................20” SPOUT ASSY NO MAGNET 4 2 8 5 5A 7 6 1A 1B 3 REF. NO PART NO. 1A 1B 2 3 4 5 5A 5B 6 7 8 850093 850094 150383 183152 850050 750019 400712 850053 400205 402005 407021 DESCRIPTION 5B QTY. 20” SPOUT WELDMENT WITH MAGNET............................... 1 20” SPOUT WELDMENT NO MAGNET .................................. 1 SPOUT PIVOT TUBE.........................................
SPOUT MAGNET ASSEMBLY 1 7 3 8 5 4 2 6 4 5 REF. NO PART NO. 1A 1B 2 3 4 5 6 7 8 850106 850093 150299 357005 400205 402005 402405 407021 407022 DESCRIPTION QTY. 17” SPOUT WELDMENT.......................................................... 1 20” SPOUT WELDMENT.......................................................... 1 SPOUT MAGNET GUARD ....................................................... 1 ARCO PLATE MAGNET AM 2200 ........................................... 2 HEX NUT, 5/16”-18..................
SPOUT RUBBER 2 1 3 REF. NO PART NO. DESCRIPTION QTY. 1 A B 2 3 150384 150403 150150 183152 SPOUT RUBBER (17” SPOUT) ............................................... 1 SPOUT RUBBER (20” SPOUT) ............................................... 1 SPOUT RUBBER END PLATE ................................................ 2 SPOUT BACK-UP ANGLE.......................................................
CHAIN CONVEYOR ASSEMBLY 18 9 12 13 3 10 2 11 5 1 1 6 8 4 7 16 20 11 15 21 19 17 14 48
CHAIN CONVEYOR ASSEMBLY #781414 .............. 24”L x 48”W CONVEYOR ASSEMBLY #781464 .............. 36”L x 48”W CONVEYOR ASSEMBLY #781465 .............. 48”L x 48”W CONVEYOR ASSEMBLY REF. NO PART NO. 1 2 3 4 5 6 7 8 9 10 11 12 160025 188427 188428 340316 402006 405652 400205 402005 407021 409916 188390 874126 874004 874122 874128 874136 874124 188304 188384 188432 188418 874127 874154 874153 341323 400210 400810 760000 13 14 15 16 17 18 19 20 21 22 DESCRIPTION QTY. 8 TOOTH #55 SPROCKET x 1”ID .....
CHAIN CONVEYOR HYDRAULIC ASSEMBLY TO MOTOR TO TRACTOR 4 TO CONV DOWN FRONT 9 END SHEET 9 TO TRACTOR 3 3 5 10 7 7 13 9 2 14 9 17 7 3 10 1 4 11 6 A TO MOTOR PORT B TO CONV UP 8 B 4 12 11 2 15 16 CONVEYOR CYLINDER 8 REF. NO 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 PART NO. 874071 781329 781328 781327 781236 409916 368608 368118 368031 368028 368007 364060 362283 362240 360009 332654 310805 DESCRIPTION QTY. CONVEYOR MOTOR PLATE WELDMENT .........................1 HYD.
CONVEYOR HYDRAULIC ASSEMBLY (TWO CYLINDERS) REF. NO 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 PART NO. 781355 781328 781337 781356 781067 368608 368118 368031 368028 368007 364060 362283 362240 310805 874071 409916 332654 360009 368607 368110 DESCRIPTION QTY. HYD HOSE ASSY 3/8” x 105” (3/8” MP ENDS)............... 1 HYD. HOSE ASSY 1/2” x 128” (1/2”MP ENDS)............... 2 HYD. HOSE ASSY 1/2” x 80” (1/2”MP ENDS)................. 2 HYD. HOSE ASSY 3/8” x 81” (3/8”MP ENDS)................. 2 HYD.
4-15 SCALE INDICATOR ASSEMBLY 11 10 12 13 6 5 8 16 1 4 7 15 9 2 3 14 REF. NO PART NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 872125 872126 185490 185491 185493 185303 184283 185492 401108 405714 400206 402006 405653 400906 405661 412205 DESCRIPTION QTY. TRAILER SCALE ARM WELDMENT ................................... 1 TRAILER SCALE INDICATOR WELDMENT....................... 1 TRAILER SCALE INDICATOR TUBE ................................... 1 HINGE PLATE ....................................
524-15 OIL BATH DOOR ASSEMBLY 1 2 12 9 8 7 6 3 10 1 4 13 14 11 REF. NO PART NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 351056 370323 370322 370321 370320 370319 370317 370316 189503 872639 850585 850586 850575 850574 DESCRIPTION 5 QTY. RUBBER BULB SEAL, 5/32” ................................................ 27’ LEVELING PAD ....................................................................... 4 HANDLE STOP.........................................................................
524-15 LUBRICATION ASSEMBLY A C B D E F 1 VIEW A-A 2 2 3 5 2 2 6 4 A 2 A 5 REF. NO PART NO. 1 2 3 A E 4 B 5 C D 6 F 310750 356001 150212 185044 185341 150211 DESCRIPTION 3 QTY. 1/8” PTF GREASE ZERK ......................................................... 6 1/8” NFPT x 3/16” COMP. 90°................................................. 12 3/16” COPPER GREASE LINE X 69”...................................... 2 INPUT SHAFT BEARING ROTOR BEARING 3/16” COPPER GREASE LINE X 39”...............
524-15 STAGGERED ROTOR 5 4 6 10 9 7 8 2 3 REF. NO PART NO. 1 2 3 4 5 6 7 8 9 10 11 190338 190339P 407322 401106 402406 407102 400908 402408 850544 872874 780078 DESCRIPTION 1 QTY. WIPER CHANNEL 12-13/16"x32".......................................... 18 PLASTIC WIPER 10-7/8" x 35-1/4" ........................................ 18 ELEVATOR BOLT PLTD 3/8" x 1-1/4"................................. 108 3/8" - 16 HEX NYLOC NUT #5 PLTD...................................
3 ARM ROTOR ASSEMBLY (FROM SERIAL #890573481 TO PRESENT) 1 8 3 2 13 7 9 11 5 10 6 4 12 REF. NO PART NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 850122 850125 850007 150344 150343 150346 150345 410005 406489 400912 401106 405654 850544 750030 DESCRIPTION QTY. 524 3-ARM ROTOR WELDMENT .......................................... 1 524 WIPER TUBE WELDMENT ............................................. 3 ROTOR SPRING COVER WELDMENT................................. 6 END WIPER STRAP ........................
5 ARM ROTOR ASSEMBLY (FROM SERIAL #890573481 TO PRESENT) 9 1 8 3 10 2 13 7 5 11 6 4 12 REF. NO PART NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 850248 850125 850007 150344 189343 150346 150345 410005 406489 400912 401106 405654 850544 750030 DESCRIPTION QTY. 524 5-ARM ROTOR WELDMENT .......................................... 1 524 WIPER TUBE WELDMENT ............................................. 5 ROTOR SPRING COVER WELDMENT................................ 10 END WIPER STRAP ............................
524 TOP & BOTTOM AUGER ASSEMBLIES (FROM SERIAL #890573481 TO PRESENT) TOP AUGER 2 4 1 TOP AUGER (OPTIONAL) 3 7 6 12 9 13 8 11 14 5 10 BOTTOM AUGER REF. NO PART NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 850131 382026 150126 850542 850131B 382026 381625 382023 150126 850127 382021 382020 150411 850543 DESCRIPTION QTY. TOP AUGER 3/8” FLIGHT WELDMENT .......................... 1 FLIGHT RH 20”OD x 6 5/8”ID x 3/8” x 14” PITCH ............9-1/2 TOP AUGER PADDLE ..........................................
524 FRONT END ASSEMBLY (FROM SERIAL #890573481 TO PRESENT) 1 3 2 REF. NO PART NO. 1 2 3 340436 340437 340446 DESCRIPTION QTY. LB F3Y235N 2-3/16” 4-BOLT FLANGE BEARING .............. 1 LB F3Y239N 2-7/16” 4-BOLT FLANGE BEARING .............. 1 LB F247 2-15/16” 4-BOLT FLANGE BEARING ....................
33 34 40 37 60 43 38 42 43 34 34 42 43 33 41 40 37 36 39 42 35 37 1 11 2 12 33 34 43 3 32 14 5 4 16 19 30 15 17 6 21 18 28 8 13 20 7 10 9 11 29 27 22 31 24 23 9 21 8 10 26 9 24 10 25 524 DRIVE ASSEMBLY (FROM SERIAL #890573481 TO PRESENT)
340556 189545 850519 189546 185319 331213 150599 850129 402010 405754 340438 331002 331001 13 189104 14 150363 15 330849 16 781037 A 355039 17 340439 18 330825 330805 19 342048 1 2 3 4 5 6 7 8 9 10 11 12 REF# PART# QTY. 3-1/2” MSF 56 4-BOLT FLANGE BRG........ 1 3-1/2” SHAFT SPACER-13/32 ...................... 1 #120 B 48 SPROCKET WELDMENT ........... 1 3” SHAFT SPACER-3/8................................. 1 3-1/2” SHAFT SPACER-1/2 .......................... 1 #120 B 13H SPROCKET..........................
1 2 24 23 21 22 3 4 7 5 6 8 19 18 20 17 10 11 9 13 14 62 15 16 12 524 STATIONARY DRIVE ASSEMBLY
150395 185641 780015 355028 320720 332612 185480 332614 344023 324016 336022 185484 781001 325106 324009 336031 185485 850149 872003 850147 185087 340228 330825 340439 781037 355039 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 A A PART NO. REF. NO QTY. 524 ELECTRIC INPUT SHAFT - 17..........................................1 COVER PLATE .........................................................................1 1-3/4” SEAL PLATE ASSEMBLY ..............................................
524 200 SERIES 3:1 GEARBOX ASSEMBLY (#344023) 1 2 9 3 4 5 4 7 6 3 6 2 2 3 7 4 8 10 9 4 3 2 1 REF. NO PART NO. 1 2 3 4 5 6 7 8 9 10 344214 344215 344211 344210 344220 344213 344209 344223 344219 344212 DESCRIPTION QTY. CLOSED END CAP................................................................... 2 END CAP GASKET .................................................................. 4 BOX BEARING CUP 18620 .....................................................
524 TRUCK DRIVELINE ASSEMBLY 3 ITEMS 1 & 5 ARE CUT TO LENGTH AND WELDED AT INSTALLATION. 4 2 4 1D 1C 3 1A 1B 8C 8A 8B 5A 7 5C 6 5A 5B REF. NO PART NO. 1 780486 338420 338435 338053 338422 183327 340221 183319 780494 338422 338435 338053 344023 183251 338042 338449 338443 338451 A B C D 2 3 4 5 A B C 6 7 8 A B C CHECK OIL HERE DESCRIPTION QTY. 1280 DRIVESHAFT ASSY. 1-1/4” x 1-3/8” ............................. 1 1-1/4” SPICER YOKE..............................................................
524 TRUCK W-2400 DRIVESHAFT ASSEMBLY (#385560) 1 2 4 5 3 3 7 2 8 6 REF. NO PART NO. 1 2 3 4 5 6 7 8 338451 338443 338473 338450 338447 338448 338452 338449 DESCRIPTION QTY. W-2400 YOKE 1-3/4”RB 3/8” KEYWAY ................................... 1 W-2400 CROSS KIT................................................................. 2 WALTERSHIED #10 METRIC ROLL PIN................................. 2 W-2400 INBOARD YOKE.........................................................
540 & 1000 TRAILER PTO DRIVELINE ASSEMBLY 4 8 4 10 2 2 11 3 2 1 4 12 5 7 6 REF. NO PART NO. 1 2 3 4 5 6 7 8 9 10 11 12 332612 185480 320720 340229 183277 341028 150386 850136 185299 780601 338030 338442 9 DESCRIPTION QTY. 60 B 20 x 1-3/4” CHAIN COUPLING SPRKT........................... 2 3/8” SQ. KEY x 2” ..................................................................... 3 #60-2 RC x 20 PITCHES COMP .............................................. 1 1-3/4” FX3W228U 2-BOLT FLANGE BEARING ...
524 TRAILER DRIVESHAFT W-2400 (#383399) 12 10 3 1 9 REF. NO 1 A B 2 3 4 5 6 7 8 9 10 11 12 4 2 11 6 PART NO. 338444 338442 338443 338473 338450 338474 338467 338452 338449 338486 338487 338488 338489 5 3 7 12 DESCRIPTION 9 2 8 QTY. YOKE (TRACTOR END) YOKE 540 RPM ....................................................................... 1 YOKE 1000 RPM ..................................................................... 1 CROSS KIT ...........................................................
524 TRAILER LOADCELL SCALE PARTS LOADCELL 1 5 2 6 3 4 3 4 6 5 REF. NO PART NO. 1 2 3 4 5 6 182881 182915 185997 870501 872245 870519 DESCRIPTION QTY. SCALE MOUNT MIXER PAD................................................... 4 LOADCELL CAGE PLATE ....................................................... 8 3/8” SCALE PAD ...................................................................... 8 CHECK ROD WELDMENT ...................................................... 2 OFFSET CHECK ROD WELDMENT .....
524 TRAILER WIEGH BAR ASSEMBLY 3 2 1 REF. NO PART NO. 1 2 3 189294 872360 860055 DESCRIPTION QTY. WEIGH BAR MIXER PAD ........................................................ 4 2-1/2” T-BAR WELDMENT ....................................................... 4 2-1/2” BAR BLOCK WELDMENT .............................................
524 TRUCK SCALE FRAME ASSEMBLY 3 6 7 5 8 4 2 1 REF. NO PART NO. 1 2 3 4 5 6 7 8 870527 182998 870519 872053 870501 182881 182915 185997 DESCRIPTION QTY. SCALE FRAME WELDMENT................................................... 1 TRUCK FRAME BRACKET...................................................... 4 MIXER CHECK WELDMENT ................................................... 2 OFFSET CHECK ROD............................................................. 1 CHECK ROD ..............................
524 TRUCK 2-1/2” WEIGH BAR SCALE FRAME ASSEMBLY 3 1 4 WELDED TO MIXER BASE AT INSTALLATION 2 REF. NO PART NO. 1 2 3 4 872163 872159 182998 185609 DESCRIPTION QTY. 524 TRUCK WEIGH BAR FRAME ......................................... 1 2-1/2” WEIGH BAR MOUNT WELDMENT .......................... 4 TRUCK FRAME BRACKET.................................................... 4 BART MOUNT MIXER PAD...................................................
524 STATIONARY LOAD CELL SCALE FRAME ASSEMBLY 5 6 7 3 6 2 4 2 4 1 3 REF. NO PART NO. 1 2 3 4 5 6 7 850150 870501 871053 870519 182881 182915 185997 DESCRIPTION QTY. 524 STATIONARY SCALE FRAME WELDMENT ................... 1 SCALE CHECK ROD WELDMENT ......................................... 2 TRAILER CHECK ROD WELDMENT ...................................... 2 MIXER SCALE CHECK WELDMENT ...................................... 2 SCALE MIXER MOUNT PLATE...............................................
524 TRAILER ASSEMBLY 5 1 6 9 7 3 4 2B 8 10 1 2A REF. NO PART NO. 1 2 2A 2B 3 4 5 6 7 8 9 10A 10B 781145 651024 374100 374101 357400 870972 870733 184598 870931 750111 840110 374002 374001 DESCRIPTION QTY. 18.5 x 22.5 MOUNTED TIRE ASSEMBLY ............................... 2 PERFECT HITCH KIT (INCLUDES 2A & 2B)........................... 1 BASE HITCH BODY ................................................................. 1 CLEVIS INSERT ..........................................................
10-BOLT HUB & SPINLDE ASSEMBLY (20,000 LB.) RIGHT HAND ASSY COMPLETE - #750110 LEFT HAND ASSY COMPLETE - #750111 8 1 3 6 7 5 4 2 11 15 17 10 12 9 16 18 13 14 REF. NO PART NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 342213 342214 342215 342216 184614 372211 372212 372304 372309 400033 400034 400102 400103 402005 402904 405625 407724 407725 DESCRIPTION QTY. BEARING, 3.543” BORE, TIMKEN #HM 218248..................... 1 BEARING, 2.625” BORE, TIMKEN #HM 212049.....................
524 ROTO-HAY PROCESSOR ASSEMBLY (HYDRAULIC OPTION) 3 2 9 6 8 1 4C 4A 7 4B REF. NO PART NO. 1 2 3 4 188226 357702 780124 780109 368007 364954 364055 354400 781055 850060 872357 781070 781097 4A 4B 4C 4D 5 6 7 8 9 DESCRIPTION QTY. FEEDER ELECTRIC CONTROL BRACKET............................ 1 PUCH BUTTON SWITCH 12V-2 POLE ................................... 1 MV5 3rd VALVE ADD ON KIT .................................................. 1 CYLINDER ASSY, 2” x 8” ...................................
524 ROTO-HAY PROCESSOR ASSEMBLY 5 4 6 7 1 8 3 13 2 12 11 REF. NO PART NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 872351 850144 150198 850301 189127 872355 850302 872354 189128 150817 872353 150223 385002 DESCRIPTION 9 10 QTY. 524 HAY PAN WELDMENT ................................................... 1 524 HAY PAN TUBE WELDMENT........................................ 1 BAFFLE PLUNGER ................................................................. 1 524 CROSS BAR WELDMENT ...............................
524 ROTOR-HAY PROCESSOR (CABLE OPTION) 13 11 8 12 2 1 10 6 4 5 7 3 REF. NO PART NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 150188 150189 150190 412204 412325 850066 150186 850090 850105 150228 410009 150391 411805 9 DESCRIPTION QTY. CABLE BAR.............................................................................. 2 SLEEVE .................................................................................... 1 CABLE ...................................................................................
524 BOTTOM AUGER FLOAT ASSEMBLY 4 1 3 11 7 8 2 5 6 7 3 8 10 REF. NO PART NO. 1 2 3 4 5 6 7 8 9 10 11 850153 850154 150418 405752 405656 405655 402406 402006 402010 400210 400206 9 11 DESCRIPTION QTY. BEARING SLIDE PLATE WELDMENT 2-7/16” ................... 1 BEARING SLIDE FRAME WELDMENT ............................... 1 BEARING SLIDER PLASTIC .................................................. 2 HHCS 5/8” X 1 1/2”...................................................................
524 FENDERS & MUD FLAPS 2 1 3 1 5 2 5 4 REF. NO 1 2 3 4 5 PART NO. 872108 183087 370202 370200 872120 DESCRIPTION QTY. FENDER WELDMENT............................................................. 2 MUD FLAP STRAP .................................................................. 4 FRONT MUD STRAP ............................................................... 2 REAR MUD STRAP.................................................................. 2 MUD FLAP BRACKET WELDMENT ...............................
