GB CHILLER WATER DISPENSER Type I / Type II Operating Instructions Type I Type II www.bravilor.
GB 2012 Bravilor Bonamat All rights reserved. No part of this document may be reproduced and/or published by means of print, photoprint, microfilm or any other means without prior written permission from the manufacturer. The foregoing applies also to the figures and/or diagrams contained herein.
GB FOREWORD Using this document BEFORE USE OF THE APPARATUS FIRSTLY READ THE SAFETY BROCHURE (700.403.347). Pictograms and symbols This document contains the following pictograms and symbols: READ! Read the safety manual (700.403.347). TIP Suggestions and advice for conducting the procedures in question more easily. WARNING Procedures which −if they are not conducted with due care and attention− may result in serious damage to the device or physical injury. WARNING Danger: electric current.
Table of contents I Using this document . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . I GB FOREWORD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pictograms and symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Service and technical support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INTRODUCTION GB 1. READ! Read the safety manual (700.403.347) 1.1 A brief overview of the device 1.1.1 General description The CHILLER is a cold water (type I) or a cold sparkling water device (type II), specially designed for anyone who enjoys drinking a refreshing beaker of cool and/or sparkling water. The device can supply (8−12L) of chilled water per hour. The device’s settings are electronically controlled.
GB 2. TECHNICAL DATA READ! Read the safety manual (700.403.347) 2.1 General Model Weight (without water) Type I Type II 2.2 : Chill−003 : 16 Kg. : Standard : With CO2 Transport dimensions and weights Transport dimensions (l x h x w) Transport weight 2.3 : 550 mm x 435 mm x 360 mm : 17,5 Kg. Dimensions Device dimensions (l x h x w) 2.4 : 450 mm x 380 mm x 280 mm Electrical system TIP − See the identification label for correct values.
INSTALLATION GB 3. READ! Read the safety manual (700.403.347) 3.1 Unpacking D Verify that the device is complete. − Chiller − 1 drip−tray + grille − 1 water−connection hose − 1 Connecting cable − Water filter (optional) − 1 CO2 inlet pipe 1/4” (Type II only) − CO2 bottle and decompression valve (Type II only) provided by dealer − these operating instructions D If components are missing or damaged, please contact your dealer. 3.
3.2.3 Filter installation and replacement (optional) GB A B D Rotate like the right arrow (B) to open the filter. D Rotate like the left arrow (A) to lock the filter. 3.2.4 Using the device the first time TIP − The first time the device is used, it makes use of the default factory settings. At a later date, authorized personnel can change these settings if required. − The control system equates with a power failure memory function. See Chapter 6. − The first time the device is used, it takes approx.
EVERYDAY USAGE GB 4. READ! Read the safety manual (700.403.347) During use, the default factory setting may not be considered to be correct or adequate for the situation in which the device is being used. These settings can be adjusted −by personnel with the appropriate authorization− in accordance with the instructions in Chapter 6. Consequently, the present chapter (4.) only describes normal, everyday use of the device by any user.
GB 5. MAINTENANCE BY SPECIALLY AUTORIZED PERSONNEL READ! Read the safety manual (700.403.347) 5.1 General cleaning D Clean the exterior of the device with a damp cloth (if necessary, use a non−abrasive cleaning agent). D Use a vacuum Cleaner to clean the grille at the rear of the device. 5.2 Flushing the water system Flush the water system with clean water if you have not used it to draw off water for one to two weeks. 5.2.1 Chiller (Type I) 1. Use button 2 to draw−off approximately 0.
5.3.1.2 Chiller (Type II) GB 1. Close the water tap. 2. Use button 3 to draw off the CO2 reservoir until only CO2 gas escapes (± 2,5 l water). 3. Fill the cleaning cartridge with the two bottles of detergent. 4. Connect the cleaning cartridge to the Chiller. 5. Turn the water tap open. 6. Use button 2 to draw off approximately 0.25 liters of water. 7. Wait for about 30 minutes, the Chiller will now fill with the cleaning agent. 8. Remove the cleaning cartridge and empty the water present. 9.
GB 6. PROGRAMMING READ! Read the safety manual (700.403.347) 6.1 Programming buttons 1 6 2 5 3 4 1. 2. 3. 4. 5. 6. Water level light Reset button Temperature set (up) Temperature set (down) Cooling run light Display Fig. 3 Signalling and display 6.1.1 Temperature setting function The buttons Y and B are used for temperature setting. 1. Y : higher temperature 2. B : lower temperature 3.
Protection function 6.2.1 Compressor protection GB 6.2 When the required temperature is reached or the power supply is cut off, the compressor will stop working for 3 minutes. 6.2.2 Water source low pressure protection When the water source pressure is lower than 100 kPa or the water source switch is shut off, the water inlet valve and pump power will be cut off to have them protected in order to avoid long−time running. 6.2.
GB 7. CORRECTING MALFUNCTIONS If the device is not operating (correctly), consult the following checklist to learn whether you can resolve the problem yourself. If this is not the case, please contact your dealer. WARNING READ! Read the safety manual (700.403.347) 7.1 n Always check whether the malfunction is of a mechanical or electrical nature.
Display messages and their meaning GB 7.2 DISPLAY MESSAGES Cause/Action of the system: “E1” Something wrong with the temperature. ECopyright Bravilor Bonamat B.V. Action by the user: Call in service.
700.403.