READ THESE INSTRUCTIONS AND SAVE THEM FOR FUTURE USE Installation Guide Table of Contents: LISTED FOR DAMP LOCATION net weight of fan: 13.67 lb (6.2 kg) Safety Tips. pg. 1 Unpacking Your Fan. pg. 2 Parts Inventory. pg. 2 Installation Preparation. pg. 3 Hanging Bracket Installation. pg. 3 Fan Assembly. pgs. 4 - 5 Wiring. pgs. 6 Canopy Assembly. pg. 7 Blade* Assembly. pg. 7 Light Kit Assembly (Optional). pg. 8 Handheld Remote Control Assembly. pg. 9 Automated Learning Process./ Activating Code. pg.
SAFETY TIPS. WARNING: To reduce the risk of electrical shock, turn off the electricity to the fan at the main fuse box or circuit panel before you begin the fan installation or before servicing the fan or installing accessories. 1. READ ALL INSTRUCTIONS AND SAFETY INFORMATION CAREFULLY BEFORE INSTALLING YOUR FAN AND SAVE THESE INSTRUCTIONS. CAUTION: To avoid personal injury, the use of gloves may be necessary while handling fan parts with sharp edges. 2. 3. 4.
1. Unpacking Your Fan. Carefully open the packaging. Remove items from Styrofoam inserts. Remove motor housing and place on carpet or Styrofoam to avoid damage to finish. Do not discard fan carton or Styrofoam inserts should this fan need to be returned for repairs. Check against parts inventory that all parts have been included. 2. Parts Inventory. a. canopy. 1 piece a b c d n o b. hanging bracket. 1 piece c. 6in. downrod and hanging ball (with pin and clip). 1 piece e f d. 4in. downrod.
3. Installation Preparation. To prevent personal injury and damage, ensure that the hanging location allows the blades a clearance of 7 feet (2.13m) from the floor and 30in. (76cm) from any wall or obstruction. This fan is suitable for room sizes up to 400 square feet (37.2 square meters). 12ft. - 20ft. (3.66m - 6.1m) blade edge 30 7 feet inches (2.13 m) (76 cm) This fan can be mounted with a downrod on a regular (no-slope) or vaulted ceiling.
. Fan Assembly. stop pin Remove hanging ball from downrod provided by loosening set screw on hanging ball. Remove pin and clip. Lower hanging ball and remove stop pin. Slide hanging ball off of the downrod. [Refer to diagram 1.] Loosen yoke set screws and nuts at top of motor housing. [Refer to diagram 2.
5. Fan Assembly. (cont.) With the hanging bracket secured to the outlet box and able to support the fan, you are now ready to hang your fan. Grab the fan firmly with two hands. Slide downrod through opening in hanging bracket and let hanging ball rest on the hanging bracket. Turn the hanging ball slot until it lines up with the hanging bracket tab. WARNING: Failure to align slot in hanging ball with tab in hanging bracket may result in serious injury or death.
ground (green or bare) white supply wire 6. Wiring. black supply wire WARNING: Turn off circuit breakers to current fixture from breaker panel and be sure switch is turned to the OFF position. ground (green or bare) blue CAUTION: Be sure outlet box is properly grounded and that a ground wire (GREEN or Bare) is present. black Make sure all electrical connections comply with Local Codes or Ordinances and the National Electrical Code.
7. Canopy Assembly. Locate 2 screws on underside of hanging bracket and remove screw closest to the open end of the hanging bracket. Partially loosen the other screw. Lift canopy to hanging bracket. Place rounded part of slotted hole in canopy over loosened screw in hanging bracket and push up. Twist canopy to lock. Re-insert screw that was removed, and then tighten both screws securely. hanging bracket screw canopy screw 8. Blade Assembly.
. Light Kit Assembly (Optional). motor housing If you wish to use the light kit, remove 3 screws from underside of fitter plate and save them for later use. Connect male plug from motor housing to female plug from LED light kit, matching up the colors on the male plug with the colors on the female plug for correct fit. Be sure that plugs connect securely. fitter plate Carefully arrange wiring within fitter plate. Align holes in LED light kit with holes in fitter plate.
. Handheld Remote Control Assembly. IN ORDER TO USE THE HANDHELD REMOTE CONTROL, PLEASE CONTINUE WITH SECTION 10 for remote control assembly instructions. If you have already installed the wall control but do not wish to use the handheld remote control, please proceed to Section 11. remote control cover Gently pull on remote control cover to separate top and bottom parts. [Refer to diagram 1.
. Automated Learning Process./Activating Code. CAUTION: The wall and/or handheld remote control can be programmed to multiple receivers or fans. If this is not desired, turn wall switch off to any other programmable receiver or fan. Restore electrical power and then, if using wall control, set slider switch on wall control to the ON position. Within 60 seconds of turning on the wall control, press and hold the OFF button on the wall control for 5 seconds or until light blinks twice.
Troubleshooting. Warranty. WARNING: Failure to disconnect power supply prior to troubleshooting any wiring issues may result in serious injury. LIFETIME LIMITED WARRANTY: warrants this fan to the original household purchaser for indoor use under the following provisions: 1-YEAR WARRANTY: will replace or repair any fan which has faulty performance due to a defect in material or workmanship. Contact Customer Service to arrange for return of fan. Return fan, shipping prepaid, to .
