Assembly Instruction

ManualsBrandsBrayden Studio ManualsCeiling LightsJancis 4-Light Single Drum Pendant

Part

Description

Quantity

A Crossbar

1pc.

2 pcs.

1pc.

2 pcs.

Ceiling Canopy

Hex Nut

Lock Washer

Package Contents

Warnings and Cautions

Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.

These instructions are provided for your safety. It is very important you read them completely before installing

the fixture. We strongly recommend that a licensed, professional electrician perform the installation.

Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool

before removal. Do not subject glass parts to any shock while in operation or shattering may result.

Mounting Ball

Mounting Screw

6” Rod

1of6

2 pcs.

12” Rod

1pc.

Socket Assembly

1pc.

Diffuser

Center Stem

Rubber Washer

1pc.

Flat Washer

1pc.

Hex Nut

1pc.

Finial

ToolsRequired:Flatheadscrewdriver, Phillips screwdriver,pliers,wirecutters,wire

strippers,electricaltape,safetyglasses.

EstimatedAssemblyTime:20-30 minutes

BulbRecommended: (4)MediumBase 100W Maximum

Preparation:Identifyandinspectallpartsbeforebeginninginstallation.Checkpackage

contentlistanddiagramsbelowtobesureallpartsarepresent.Ifanypartsaremissing

ordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomer

serviceforreplacementparts.

Assembly Instruction

Thank you for purchasing a product.

Need assistance with parts or assembly? Call our customer service

Summary of content (6 pages)

PAGE 1
Assembly Instruction Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses. Bulb Recommended: (4) Medium Base 100W Maximum Estimated Assembly Time: 20-30 minutes Preparation: Identify and inspect all parts before beginning installation. Check package content list and diagrams below to be sure all parts are present. If any parts are missing or damaged, do not attempt to assemble, install, or operate the fixture.
PAGE 2
PAGE 3
Assembly Instruction STEP 1 - Assemble Rods 6” Rod with Fixture Loop Figure 1 A. Determine the Rods (G/H) to be assembled to the Socket Assembly (I) according to your hanging height. B. Pass Supply Wires and Ground Wire through the chosen Rods (G/H) and then thread the chosen Rods (G/H) and the Socket Assembly (I) together. Hand tighten until snug. 6” Rod 12” Rod with Nipple 12” Rod Supply Wire and Ground Wire Socket Assembly STEP 2 - Assemble Ceiling Canopy to Upper Rod Figure 2 Ceiling Canopy A.
PAGE 4
Assembly Instruction STEP 4 - Attach Crossbar to Outlet Box Figure 4 Outlet Box A. Attach the Crossbar (A) to Outlet Box and secure by threading Outlet Box Screws (not supplied) into the Mounting Holes on the Outlet Box. Tighten until snug. Crossbar Mounting Hole Outlet Box Screw STEP 5 - Make Wire Connections A. Use standard wire connectors to make all wire connections. (Connectors are not included with fixture.) Strip and prepare wire ends according to instructions supplied with connectors. B.
PAGE 5
Assembly Instruction STEP 6 - Attach Ceiling Canopy to Mounting Screw A. Place the Ceiling Canopy (F) over the Mounting Screws (B) and secure with Mounting Balls (E). Hand tighten until snug. Figure 7 Mounting Screw Ceiling Canopy Mounting Ball STEP 7 - Attach Center Stem to Socket Assembly Figure 8 A. Thread the beaded end of Center Stem (J) into Coupling inside of Socket Assembly (I). Hand tighten until snug. Socket Assembly Coupling Center Stem STEP 8 - Attach Diffuser to Fixture Figure 9 A.
PAGE 6
Assembly Instruction Figure10 STEP 9 - attach Finial to fixture A. Thread Finial (O) onto Center Stem, hand tighten until snug. Center Stem Finial Figure 11 STEP 10 - Install Bulb Socket A. This fixture uses standard bulb with a standard screw base. Maximum 100 watts. B. Insert bulb and screw properly into place. Bulb Your fixture is now assembled and ready to use. Enjoy! Thank you for purchasing a product.