Installation & Safety Instructions
INSTALLATION AND SAFETY INSTRUCTIONS
FOR YOUR SAFETY
WARNING: BE SURE THE ELECTRICITY TO THE WIRES YOU
ARE WORKING ON IS SHUT OFF; EITHER THE FUSE IS
REMOVED OR THE CIRCUIT BREAKER IS SHUT OFF. GENERAL
You don’t need special tools to install this fixture. Be sure to follow the
steps in the order given. Under no circumstances should a fixture be
hung on house electrical wires, nor should a swag type fixture be
installed on a ceiling which contains a radiant type heating system.
Read instructions carefully. If you are unclear as to how to proceed,
consult a qualified electrician. NOTE: Proper wiring is essential for the
safe operation of this fixture
GENERAL
You don’t need special tools to install this fixture. Be sure to
follow the steps in the order given. Under no circumstances
should a fixture be hung on house electrical wires, nor should a
swag type fixture be installed on a ceiling, which contains a
radiant type heating system. Read instructions carefully. If you
are unclear as to how to proceed, consult a qualified electrician.
NOTE: Proper wiring is essential for the safe operation of this
fixture
FIXTURE ASSEMBLY
Carefully removed the fixture from the carton and check that all parts
are included as shown in figure. Be careful not to misplace any of the
screws or parts, which are needed to install this fixture.
INSTALLATION
IMPORTANT: Do not attach fixture directly to outlet box.
STEP1: Assemble the rods (F) together, then thread the bottom
end of rod (F) into the coupling (E) and thread the bottom end of
swivel (G) onto the top end of rod (F).
STEP2: Insert the top end of swivel (G) through the ceiling
canopy (H) and the reinforced metal plate (I) and secure with nut
(J)
STEP3: Take the mounting plate (L) over the outlet box and adjust it to
the proper position, then make the marks on the ceiling for the 2 key
holes’ position.
STEP4: Drill the holes at the position where marked at the step 1, and
install the plastic anchors (N) into them well;
STEP5: Attach the mounting plate (L) onto the outlet box using 2 wood
screws (M) thread into the plastic anchors (N) and let the wood screws
(M) set at the long slot of the key hole well, then secure the outlet box
screw (P) through the mounting holes of the mounting plate (L) and the
outlet box tightly.
Proceed to connect wires:
GROUNDING INSTRUCTIONS
STEP 1: Insert the green grounding screw into the hole with
two raised dimples on the circular strap. Wrap the ground wire
from the fixture (if supplied) around the green grounding
screw, then connect it to ground wire from the outlet box (if
not fixed on the outlet box) using a wire connector (not
supplied). If ground wire from the fixture is not supplied, wrap
the ground wire (if not fixed on the outlet box) from the outlet
box around the green grounding screw and tighten it.NEVER
CONNECT GROUND WIRE TO BLACK OR WHITE POWER
SUPPLY WIRES
STEP 2: Take note of the color of the wire(s) on your fixture.
Identify which group your fixture wire(s) falls into and
connect the wires according to the directions below
*NOTE: When parallel wire (SPT-I & SPT-2) is used, the tracer
wire is square shaped or ridged and the less tracer wire is round in
shape or smooth (seen best when viewed from wire end.)
STEP 3: Take your fixture wire(s) from group A and place evenly
against the black wire from the outlet box. Do NOT twist wires
together before using wire connectors
STEP 4: Fit a wire connector (not supplied) over the wires and screw
the connector clockwise until you feel a firmness
STEP 5: Try gently to pull the connector off the wires. If you can pull
the connector off, carefully re-do steps 3 and 4, as above, and check
again for a firm connection
STEP 6: Connect the fixture wire from group B to the white wire from
the outlet box in the same manner
FINAL ASSEMBLY
STEP1: After wires are connected, tuck them carefully inside outlet
box.
STEP2: Put the ceiling canopy (H) over the mounting plate (L) and let
the mounting screw (O) protrude through the mounting holes on the
canopy and secure with the ball finial (H).
STEP3: put the glass (C) and Ring (P) over the socket (D) and
secure with socket cup (B) well.
STEP4: Install the Edison bulb (A) (not included) on the socket (D).
CLEANIG
To clean, wipe fixture with a soft cloth. Clean glass with a mild
soap. Do not use abrasive materials such as scouring pads or
powders, steel wool or abrasive paper.
ORDERINGPARS
Keep this sheet for future reference, and in case you need to
order replacement parts. All parts for this fixture can be
ordered from place of purchase. Be sure to use exact wording
from illustration when ordering parts.
GROUP A: Connect to Black
House Wire
GROUP B: Connect to White
House Wire
BLACK
WHITE
*PARALLEL WIRE (round &
smooth)
*PARALLEL WIRE (square &
ridged)
WHITE OR GREY WITH
TRACER
WHITE OR GREY WITHOUT
TRACER
BROWN GOLD OR BLACK
WITHOUT TRACER
BROWN, GOLD OR BLACK
WITH TRACER
Line art shown may not exactly match the fixture
enclosed. However, the installations do apply to this
fixture.