Installation & Assembly

1) Pass wire from fixture through stem and screw stem to top
of fixture. NOTE: Thread locking compound must be applied
to all stem threads as noted with symbol (3) to prevent
accidental rotation of fixture during cleaning, relamping, etc.
2) Pass fixture wire through remaining stems and screw stems
together.
3) Thread one small threaded pipe into end of each small loop.
4) Pass fixture wire from last stem through first loop. Thread
first loop onto end of last stem.
5) Pass fixture wire through second loop and through hole in
canopy. Pass threaded pipe at end of second loop through
hole in canopy.
6) Pass fixture wire through hole in lockwasher. Thread
lockwasher onto threaded pipe protruding from inside
canopy.
7) Pass fixture wire through hole in hexnut and thread hexnut
onto end of threaded pipe.
8) Attach chain link to small loop at end of stem and to loop on
canopy.
9) TURN OFF POWER.
IMPORTANT: Before you start, NEVER attempt any work
without shutting off the electricity until the work is done.
a) Go to the main fuse, or circuit breaker, box in your
home. Place the main power switch in the “OFF” position.
b) Unscrew the fuse(s), or switch “OFF” the circuit breaker
switch(s), that control the power to the fixture or room that
you are working on.
c) Place the wall switch in the “OFF” position. If the fixture
to be replaced has a switch or pull chain, place those in
the “OFF” position.
10) Thread hexnut onto threaded pipe so that 5 threads are
exposed above hexnut. Thread that end of the threaded
pipe into mounting strap and tighten hexnut against mounting
strap. Screw second hexnut onto end of threaded pipe
protruding from back of mounting strap.
11) Attach mounting strap to outlet box. (Screws not provided.)
12) Grounding instructions: (See Illus. A or B).
A) On fixtures where mounting strap is provided with a
hole and two raised dimples. Wrap ground wire from
outlet box around green ground screw, and thread into
hole.
B) On fixtures where a cupped washer is provided. Attach
ground wire from outlet box under cupped washer and
green ground screw, and thread into mounting strap.
If fixture is provided with ground wire. Connect fixture
ground wire to outlet box ground wire with wire connector.
(Not provided.) After following the above steps. Never connect
ground wire to black or white power supply wires.
13) Make wire connections (connectors not provided.) Reference
chart below for correct connections and wire accordingly.
14) Push fixture to ceiling, carefully passing threaded pipe
through hole.
15) Screw finial onto threaded pipe. Tighten finial to secure
fixture to ceiling.
16) Insert recommended bulb.
Connect Black or
Red Supply Wire to:
Connect
White Supply Wire to:
Black White
*Parallel cord (round & smooth)
*Parallel cord (square & ridged)
Clear, Brown, Gold or Black
without tracer
Clear, Brown, Gold or Black
with tracer
Insulated wire (other than green)
with copper conductor
Insulated wire (other than green)
with silver conductor
*Note: When parallel wires (SPT I & SPT II)
are used. The neutral wire is square shaped
or ridged and the other wire will be round in
shape or smooth (see illus.)
Neutral Wire
GREEN GROUND
SCREW
CUPPED
WASHER
A
B
OUTLET BOX
GROUND
FIXTURE
GROUND
DIMPLES
WIRE CONNECTOR
(NOT PROVIDED)
OUTLET BOX
GROUND
GREEN GROUND
SCREW
FIXTURE
GROUND
CANOPY
ESCUDETE
STEM
VÁSTAGO
HEXNUT
TUERCA HEXAGONAL
LOOP
ANILLO
CHAIN LINK
ESLABÓN DE CADENA
4
MOUNTING STRAP
PLANCHA PARA MONTAR
3
FINIAL
CAPUCHON
SEE OTHER SIDE FOR SPANISH TRANSLATIONS.
VEA EL OTRO LADO DE TRADUCCIONES AL ESPAÑOL.