60" or 52" CEILING FAN READ AND SAVE THESE INSTRUCTIONS FAN RATING AC 120V. 60Hz FOR DAMP LOCATION Please do not use any electric or battery powered tools in the assembly and installation of this.
TABLE OF CONTENTS Tools and Materials Required.........................................................................................1 Package Contents ......................................................................................................... 1 Safety Rules................................................................................................................... 2 Mounting Options........................................................................................................
1. TOOLS AND MATERIALS REQUIRED Philips screwdriver Blade screwdriver 11 mm wrench Step ladder Wire cutters 2. PACKAGE CONTENTS Unpack your fan and check the contents. You should have the following items: i b j a-1. Blade set (3) a-2. Blade set (5) b. Hanger bracket assembly c. Ball / down rod assembly d. Coupling cover e. Fan motor assembly f. Fan housing g. Mounting plate h. 16W LED light kit i. Glass shade assembly j. Additional metal light cover k. Transmitter+holder+2 mounting screws l.
3. SAFETY RULES 1. To reduce the risk of electric shock, insure electricity has been turned off at the circuit breaker or fuse box before beginning. 8. To avoid personal injury or damage to the fan and other items, be cautious when working around or cleaning the fan. 2. All wiring must be in accordance with the National Electrical Code and local electrical codes. Electrical installation should be performed by a qualified licensed electrician. 9.
4. MOUNTING OPTIONS If there isn't an existing UL listed mounting box, then read the following instructions. Disconnect the power by removing fuses or turning off circuit breakers. Outlet box Secure the outlet box directly to the building structure. Use appropriate fasteners and building materials. The outlet box and its support must be able to fully support the moving weight of the fan 15.9 kgs (35lbs) or less. Do not use plastic outlet boxes.
5. HANGING THE FAN Ceiling hanger bracket REMEMBER to turn off the power. Follow the steps below to hang your fan properly. Ceiling canopy 1. Remove the decorative canopy bottom cover from the canopy by turning the cover counter clockwise. (Fig. 5) Canopy cover 2. Remove the hanger bracket from the canopy by removing the 1 of 2 screws from the bottom of the hanger bracket and loosening the other one a half turn from the screw head.
6. MAKE THE ELECTRIC CONNECTIONS Outlet box White ("AC IN N") Remember to disconnect the power. Follow the steps below to connect the fan to your household wiring. Use the wire connecting nuts supplied with your fan. Secure the connectors with electrical tape. Make sure there are no loose strands or connections. Green or bare copper (ground) Black ("AC IN L") Ground (green) (Connect to ground wire on hanger bracket if no house ground wire exists.) Black (motor) White (neutral) 1.
7. FINISHING THE INSTALLATION Outlet box Hanger bracket STANDARD CEILING INSTALLATION Screws 1. Tuck connections neatly into ceiling outlet box. Canopy 2. Slide the canopy up to hanger bracket and place the key hole on the canopy over the screw on the hanger bracket, turn canopy until it locks in place at the narrow section of the key holes. (Fig. 10) Canopy cover 3. Align the circular hole on canopy with the remaining hole on the hanger bracket, secure by tightening the two set screws.
8. ATTACHING THE FAN BLADES 1. Fasten blade to motor using the flat washers, lock washers and screws supplied. (Fig. 12) 2. Repeat process with other blades. Tighten each screw and make sure the blade is straight. NOTE: This fan is supplied with two types of blades for installation. Follow the step below to installing your fan blade properly. The inner holes are for 3 blades. (for PA3-CR) The outer holes are for 5 blades. (for PA5-CR) Blade Flat washers Lock washers Screw Figure 12 9.
. INSTALLING THE LIGHT KIT REMEMBER: To disconnect the power. If you do not plan to install the light kit with your fan at this time, skip step 1, 2, 3 & 4. 1. Remove 1 of the 3 screws from the mounting plate and loosen the other 2 screws. (Do not remove) 2. Raise and hold the LED light kit close to the mounting plate and proceed to do the wire connections. Make the 2-pin wire connections: (Fig. 14) - Red to white - Black to black Mounting plate Slots Connectors 3.
. PROGRAMMING YOUR FAN AND OPERATING THE REMOTE CONTROL Your DC brushless motor is equipped with a automatically learned type remote control. Before programming takes place, fan must be fully assembled and mounted to the ceiling with blades attached. Install one 23A/12V battery (included). To prevent damage to transmitter, remove the battery if not used for long periods of time (Fig. 15) ON ECE 1 2 3 4 Restore power to ceiling fan and test for proper operation. A.
RPM for 3 minutes. When counterclockwise rotation has finished, the fan will automatically reverse to clockwise direction again to the highest RPM for 3 minutes. Fan will shut off when the self calibration test has finished. The total self calibration test will last about 6 minutes. NOTE: If the self calibration test failed, turn the AC power off; restore power and process the self calibration test again. NOTE: During self calibration test, the remote is non-fuctional.
CARE OF YOUR FAN Here are some suggestions to help you maintain your fan 1. Because of the fan's natural movement, some connections may become loose. Check the support connections, brackets, and blade attachments twice a year. Make sure they are secure. (It is not necessary to remove fan from ceiling.) 2. Clean your fan periodically to help maintain its new appearance over the years. Use only a soft brush or lint-free cloth to avoid scratching the finish.
LIMITED LIFETIME WARRANTY LIMITED WARRANTY Ceiling fans are warranted by us to the original user against defects in workmanship or materials under normal use and inside installation for: Motors: Lifetime of original purchaser: Labor & Component parts: (lights, finish, blades, etc…): one year after date of purchase, Light Bulbs: no warranty.
