Installation Guide

ManualsBrandsBrayden Studio ManualsCeiling LightsHemel 3 - Light Unique / Statement Teardrop Pendant

1of2

Warnings and Cautions

Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.

These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly

recommend that a licensed, professional electrician perform the installation.

Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.

(3)B10CandelabraBasebulbs60WMaximum,bulbnotincluded.

MinimumHangingHeightis26”,MaximumHangingHeightis62”.

30-45minutes

LightSource:

FixtureHangingHeight:

EstimatedAssemblyTime:

Preparation:

Package Contents

Fixture Loop

6” Rod

Socket Assembly

Hardware Contents

12” Rod

Crossbar

Assembly

Ceiling Canopy

Quick Link

Center Column

Glass

STEP 2 Install Fixture Loop and Rods to Fixture Body-

A. Determine the Rods (B/C) to be assembled to the Fixture Body

according to your hanging height.

B. Pass the supply wires and ground wire through the chosen rods (B/C)

and the Fixture Loop (A). Thread the Fixture Body, the chosen Rods

(B/C) and the Fixture Loop (A) together. Hand tighten until snug.

Suggested rods for Ceiling height :

8’ ceiling : use (1) 12” rod

9’ ceiling : use (2) 12” rods

10’ ceiling : use (2) 6” rods and (2) 12” rods

Figure 1

Supply

Wires and

Ground Wire

STEP 3 - Install the Crossbar Assembly to Outlet Box and Adjust

the length of the Nipple

A. Attach the Crossbar Assembly (AA) to the Outlet Box with the head of

the Green Ground Screw facing you. Secure it with Outlet Box Screws

(not included), tighten until snug

B. Adjust the hex nut and lock washer underside of the crossbar to the

middle of the nipple.

C. Remove the canopy lock ring from the canopy chain loop. Place the

Ceiling Canopy (CC) over the canopy chain loop against the ceiling to

determine the correct position of the nipple. Thread the canopy lock

ring onto the canopy chain loop. Adjust the nipple to allow the Ceiling

Canopy (CC) to rest against the ceiling when held in place by the

canopy lock ring.

D. Remove the canopy lock ring and the Ceiling Canopy (CC). Tighten

the lock washer and the hex nut against the crossbar to secure in

place.

Figure 3

Outlet Box Screw

(not included)

Hex Nut and

Lock Washer

Outlet Box

Green Ground Screw

Canopy Chain Loop

Canopy Lock Ring

Nipple

Figure 2

STEP 1 Install the Glass, the

Center Column, the

Socket Assembly

a. Thread the Glass (F), the

center column (D) and the

socket assembly (E) together

as shown. Hand tighten until

snug.

Installation Guide

Care+Maintenance

Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtoensureallpartsare

present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.MissingParts?Contactyouroriginalplaceof

purchase.

Pleasegoto forproductcleaningtips.Gotothe selection.

ToolsRequired: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses.

Summary of content (2 pages)

PAGE 1
Installation Guide Please go to for product cleaning tips. Go to the Care + Maintenance selection. Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses. Light Source: (3) B10 Candelabra Base bulbs 60W Maximum, bulb not included. Fixture Hanging Height: Minimum Hanging Height is 26”, Maximum Hanging Height is 62”. Estimated Assembly Time: 30-45 minutes Preparation: Identify and inspect all parts before beginning installation.
PAGE 2
STEP 4 - Install the Fixture Chain and Ceiling Canopy STEP 6 - Install the Bulb A. Pull the supply wires and ground wire through the Canopy Lock Ring and the Ceiling Canopy (CC) in order. B. Connect the Fixture Loop (A) to the Canopy Chain Loop by using the Quick Link. The fixture will now hang safely. C. Feed the Supply Wires and Ground Wire through the Canopy Chain Loop and Nipple into the Outlet Box. Cut the wires leaving approximately 8” of wire extending from the Outlet Box. D.