Assembly Instruction

ManualsBrandsBreakwater Bay ManualsCeiling LightsDickerson 1-Light Single Jar Pendant

(1)A19MediumBaseBulb100WMaximumor

(1)MediumBaseVintageBulbisrecommendedbutnotsupplied.

30-45minutes

Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare

present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomerserviceforreplacement

parts.

LightSource:

EstimatedAssembly Time:

Preparation:

ToolsRequired:Flatheadscrewdriver, Phillips screwdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses.

Warnings and Cautions

Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.

These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly

recommend that a licensed, professional electrician perform the installation.

Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.

Package Contents

Fixture Loop

6” Rod

Fixture

Body

12” Rod

Glass Holder

Lock Ball

Glass

Shade

Hardware Contents

Crossbar

Assembly

Ceiling

Canopy

Quick Link

STEP 1 Install Bulb-

A. Insert the bulb onto the socket

and screw snugly into place.

Socket

Vintage Bulb

(recommended

but not supplied)

Figure 1

STEP 2 Install Glass Shade-

A. Place the Glass Shade (G) over the

bulb carefully. Attach the shade

neck to the fixed shade holder on

the Fixture Body (D). With one

hand holding the Glass Shade (G),

place the Glass Holder (E) to other

side of shade neck and place it

over bolts on the fixed glass holder.

Secure them together by threading

Lock Balls (F) onto bolts. Hand

tighten until snug.

Neck

Bolt

Figure 2

STEP 3 Install Fixture Loop

and Rods to Fixture Body

A. Determine the Rods (B/C) to

be assembled to the Fixture

Body (D) according to your

hanging height.

B. Pass the supply wires and

ground wire through the

chosen rods (B/C) and the

Fixture Loop (A). Thread the

Supply

Wires and

Ground Wire

Fixture Body (D), the chosen Rods (B/C)

and the Fixture Loop (A) together. Hand

tighten until snug.

Suggested rods for Ceiling height :

8’ ceiling : use (1) 6” rod and (1) 12” rod

9’ ceiling : use (1) 6” rod and (2) 12” rods

10’ ceiling : use (2) 6” rods and (2) 12”

rods

Figure 3

Fixed Shade

Holder

Assembly Instruction

1of2

Summary of content (2 pages)

PAGE 1
Assembly Instruction Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses. Light Source: (1) A19 Medium Base Bulb 100W Maximum or (1) Medium Base Vintage Bulb is recommended but not supplied. Estimated Assembly Time: 30-45 minutes Preparation: Identify and inspect all parts before beginning installation. Check package content list and diagrams below to be sure all parts are present.
PAGE 2
STEP 4 - Install the Crossbar Assembly to Outlet Box and Adjust the length of the Nipple STEP 6 - Making the Wire Connections A. Attach the Crossbar Assembly (AA) to the Outlet Box with the head of the Green Ground Screw facing you. Secure it with Outlet Box Screws (not included), tighten until snug . B. Adjust the hex nut and lock washer underside of the crossbar to the middle of the nipple. C. Remove the canopy lock ring from the canopy chain loop.