CEILING FAN WITH LIGHT ITEM #27023 Customer Service: support@ breezary.
Installation Instructions 5-10 Troubleshooting Guide 11 Balancing Kit 12 To reduce the risk of fire or injury do not use this product in conjunction with any variable (rheostat) wall control. objects. 5. To clean the fixture ,turn off the power, wait for it to cool, and wipe the fixture with a clean dry, soft cloth. 7. All screws must be checked and retightened where necessary before installation.
17.8in 13.8in 6.2 in 72 in S5 Hardware Package S2 S6 S1.Machine Screw S2.Washer S3 S7 S1 S3.Wood Screw S4.Wire Nut S5.Blade Screw S8 S4 S6.Washer S6.Expansion Screw S8.Balance Kit OFF Item name 1.Remote Control ON/ OFF F R 3 4 2 1 SET UP STO P 7 5 6 1H 4H 8H 2.Hanger bracket 3.Canopy 4.Canopy Cover 5.Yoke Cover 6.Downrod 8 2 Quantity 2 4 4 3 26 26 2 1 1 1 1 1 1 9 7.Long Downrod 8.Motor Housing 1 1 1 4 10 5 11 9.Lamp Housing 10.LED 11.Lamp Shade 12.
Hanger bracket Receiver Canopy screw Hanger Ball Canopy Canopy Cover Yoke Cover Cotter Pin Bolt Jam Screws Motor Housing Blade Lamp housing LED Lamp Shade 4
- Take out fan downrod. - Remove cotter pin and bolt from downrod. - Take out fan motor housng. - Loosen jam screw in yoke until it is flush with the inside surface. - Place the downrod inside the canopy, canopy cover, and yoke cover. - Route wires exiting motor through yoke cover, canopy and downrod. - Insert bolt through hole in and downrod. Be careful not to damage or cut the fan wires. - Tighten bolt. Secure with cotter pin through hole in the end of the bolt.
Step2 - Secure hanger to metal outlet box. - The ceiling fan is hung on the hanger bracket, with the hanger ball groove aligned with the hanger projection. Fig.2b Fig.2a Fig.2c Outlet Box Canopy Canopy cover Outlet Box Hanger bracket washer hanger projection hanger ball groove Outlet Box Screw not provided Step3 Attaching the Fan Blades. - Attach the blade to the motor with blade screws and washer. - Repeat this step for each blade assembly. Fig.
Step4 Assembling the lamp housing - Feed the wire through the center hole of the lamp housing. - Fix the lamp housing with screws. - Connect the motor end plug to the light source end socket. Fig.4 Step5 The lampshade installation - Install the lampshade to the lamp housing by turning clockwise to lock it into place. Fig.
Step6 The receiver installation - Put the receiver in the hanger bracket. Fig.6a Fig.6b Step7 Wiring the Fan - Wiring according to the wiring diagram. FROM CEILING FROM FAN To Light white blue white blue yellow red gray yellow red gray To Motor grounding wires grounding wires (From ceiling) (From fan) grounding wires Fig.
Step8 Attaching the Canopy and Canopy cover - Slide the canopy up to the ceiling and attach it to the hanger bracket with the screws provided. Tighten all screws securely. - Move the Canopy cover onto the canopy. (the decorative cover comes with magnetism) Fig.8c Fig.8b Fig.
FUNCTION INSTRUCTION OF EMITTER - Open battery cover on the hand-held remote and install battery, pair of AAA of emitter(1.5V) that are not included. - If the emitter can not control the fan, learning code matching mode is used between emitter and receiver. Turn on the power switch, press the"SETUP"key within 3 seconds, the receiver issued a"tick"two sounds, the pair code is successful. If not successful, turn off the power for a minute an repeat the above.
Observe the fan for 24 hours after installation. Most noises associated with a new fan disappear during this time.
BALANCING PLASTIC CLIP 12 WEIGHT
