Assembly instructions

ManualsBrandsBretford ManualsOffice FurnitureTC15FF-BK

Qty Part# Description

2 022-2708 Leg Assembly Stamped with “X”

2 022-2709 Leg Assembly Stamped with “O”

1 022-2695 Top Shelf w/Grommet Hole

1 022-2699 Middle Shelf w/Grommet Hole

1 010-4791 Bottom Shelf

2 010-4785 Slide Bracket

2 030-1191 Slide

2 010-5053 Keyboard Shelf

1 010-4788 Front Panel

1 010-4789 Rear Panel

2 022-2697 Left Door Assembly

2 022-2698 Right Door Assembly

1pr. 030-1206 Rack Rail

4 010-4799 Rail Bracket

2 010-4867 Utility Shelf

2 015-0002 4” Caster w/o Brake

2 015-0003 4” Caster w/ Brake

1 E12 Electrical Unit - TC15FF ONLY

PARTS LIST

Ref Qty Part# Description

AA 24 030-0300-10T 5/8” Square Head Bolts

BB 24 030-0002 5/16-18 Hex Serrated Nuts

CC 36 030-0325 1/4-20 x 1/2” Combo Screws

DD 16 030-0240 1/4” External Lockwashers

EE 16 030-1228 8-32 x 1/4” Combo Truss Hd Screws

FF 8 030-1203 #8-32 Acorn Nuts

GG 10 02236 8-32 Hex Flange Nuts

HH 4 030-0023 #6-32 x 3/8” Rnd Hd Machine Screws

I I 4 030-0522 6-32 Locknuts

JJ 8 030-0256 1/4-20 Flange Nuts

KK 2 030-0302 #8-32 x 3/8” Screws - TC15FF ONLY

MM 8 030-0402 #10-32 x 5/8” Combo Screws

NN 8 030-0383 #10 x 1/2” “AB” Truss Hd Screws

1 010-1106 Hex Wrench

2 010-1188 Door Stop Brackets

4 012-0286 Plastic Door Handles

HARDWARE LIST

Hex Wrench (Provided)

Phillips Screwdriver

Rubber Mallet

TOOLS REQUIRED

TC15 / TC15FF

19” RACK PRESENTATION CART

WITH & WITHOUT POWER

Assembly Instructions

Summary of content (11 pages)

PAGE 1
TC15 / TC15FF 19” RACK PRESENTATION CART WITH & WITHOUT POWER Assembly Instructions PARTS LIST Qty 2 2 1 1 1 2 2 2 1 1 2 2 1pr.
PAGE 2
FIGURE 2 les P ho E U 5 C se FA e Th UST M FIGURE 1 s le N ho E I 2 C se FA e T MS Th US O M TT BO G LE Holes MUST be ALIGNED Bracket MUST fit INSIDE shelf STEP 1 Lay the rear legs on a carpeted surface exactly as shown in FIGURE 1. Slide bottom and middle onto the legs so that the brackets are inside the shelves as shown in FIGURE 2. Holes MUST be ALIGNED STEP 2 Slide the front legs onto the shelves so that the brackets are inside the shelves as shown.
PAGE 3
FULLY TIGHTEN THESE ON BOTH SIDES ONLY INSTALL IN THESE LOCATIONS BOTH SIDES STEP 3 HAND TIGHTEN shelves and legs with bolts (AA) and nuts (BB). ONLY install side hardware and middle shelf hardware as indicated. FULLY TIGHTEN MIDDLE SHELF HARDWARE. BB AA STEP 4 Insert each caster into the bottom of each leg. If caster does not insert easily, use a rubber mallet to tap caster in place. Once caster are SECURELY in place, stand unit upright.
PAGE 4
MIDDLE SHELF ATTACHMENT BOTTOM SHELF ATTACHMENT STEP 5 Attach L-brackets to one side of the cart. These should be mounted on the side that you wish the utility shelves to be installed on. Attach each bracket (2 per shelf) with screws (CC) and nuts (JJ) as shown.
PAGE 5
MIDDLE SHELF ATTACHMENT BOTTOM SHELF ATTACHMENT STEP 6 Attach the rack rails to the L-brackets with screws (CC) and nuts (JJ) as shown. The threaded holes (smaller) are facing out. CC JJ NOTE, THE RACK RAIL MUST BE INSTALLED AS SHOWN.
PAGE 6
NOTE: Separate slides by pulling on black tab. STEP 7 Separate each slide and attach outer slide piece (2 per bracket) to the slide brackets using screws (EE) and nuts (FF) as shown. NOTE: Slide may need to be extended some to align attachment holes. EE FF STEP 8 Attach each slide bracket using screws (CC) and washers (DD) as shown.
PAGE 7
STEP 9 Attach inner slide piece to keyboard shelf with screws (EE), washers (DD) and nuts (GG). EE DD GG STEP 10 Attach door stop brackets to both side of the bottom shelf with screws (HH) and nuts (I I) as shown.
PAGE 8
Panel bottom flange MUST hook onto bottom shelf STEP 11A Carefully, lay cart down as shown and slide on front panel (the one without the grommet hole). Make sure panel’s bottom flange hooks onto the bottom shelf. NOTE: Rear panel (the one with a grommet hole) goes on the same side of the cart as the grommet hole in the middle shelf. STEP 11B Attach side panel in each corner with bolts (AA) and nuts (BB). HAND TIGHTEN FOR NOW. ONCE THESE STEPS ARE COMPLETE REPEAT THEM FOR THE REAR PANEL.
PAGE 9
STEP 12 Slide top shelf onto cart as shown. Secure all 4 corners with bolts (AA) and nuts (BB). NOW TIGHTEN ALL CORNER BOLTS AND NUTS ON THE ENTIRE CART. STEP 13 - FOR TC15FF MODELS ONLY Attach the UCSE10 unit to rear panel as shown using screws (KK) and nuts (GG).
PAGE 10
STEP 14 Attach the utility shelves to the rack rails as shown with screws (MM). NOTE: You can install the shelves in any desired location along the rails. MM STEP 15 Attach a handle to each door using screws (NN) as shown.
PAGE 11
STEP 16 CC Attach the doors to each side of the cart using screws (CC) as shown. STEP 17 Slide both keyboard drawers into the cart. Part # 031-7463 Rev. 08.13.