Models 2230 and 2240 Overview ............................................................... 2 Tools Needed.......................................................... 2 Hardware................................................................3 Assembly........................................................... 4-13 Installation............................................................ 14 Document 101294 RevA 1 Drawer Removal ................................................. 15 Operation ...............
OVERVIEW COMPONENT IDENTIFICATION Perform the following sequence in order when setting up the table: Unpacking Assembly Leveling the Table Installing the Paper Roll NOTE: Save all packaging in case re-shipment is required. NOTE: Inspect all boxes and contents for damage. Report any damage to the carrier immediately. MODELS 2230 & 2240 For the above models you will receive three separate cartons: a frame & shelf carton, an upholstery carton, and a drawer carton.
MODELS 2230 and 2240 HARDWARE 1/4”-20 x 4” Screw A (Qty. 1) Allen Wrench (Qty. 1) 1/4”-20 x 2” Screw B (Qty. 11) 1/4”-20 x 1 1/4” Screw C (Qty. 8) Snap Rivet (Qty. 32) Bumper (Qty. 2) 10-24 x 1 1/4” Screw D (Qty. 2) 8-32 Nut K (Qty. 8) 8-32 x 1 1/4” Screw E (Qty. 8) Cap (Qty. 2) 1/4”-20 Nut H (Qty. 6) 1/4”-20 x 1” Screw F (Qty. 8) Clevis Pin (Qty. 2) 1/4”-20 x 1/2” Screw G (Qty. 5) J-Bolt R (Qty. 2) Cotter Pin (Qty. 2) 3/8” Nut L (Qty. 2) Document 101294 RevA 3 Washer M (Qty.
MODELS 2230 and 2240 STEP 1 Notch Screw C Screw C STEP A: Start with table frame inverted: note the position of the Notch in the drawing above is facing upwards. STEP B: Positon legs (see drawing above). Insert Screws C (1/4”-20 x 1 1/4”) and snug up by hand only at this time.
MODEL 2230 and 2240 STEP 2 Drawer Supports with holes upward and toward Foot End Screw B Foot E nd Screw B Tab Screw B Drawer Supports with holes upward and toward Foot End Screw B Screw B Shelf Support STEP A: With table in the upright position install Shelf Support using 4 Screws B (1/4”-20 x 2”). Do not tighten at this time.
MODELS 2230 and 2240 STEP 3 Caps Tab Upper Leg Screws Head End STEP A: Remove 2 Upper Leg Screws at Head End of the table, one on each of the two legs. (See illustration above.) STEP B: Insert Caps into two leg tops and seat with a rubber mallet. STEP C: Install Upper Leg Screws. Do not tighten at this time.
MODELS 2230 and 2240 STEP 4 Top Rail Tab Paper Shelf Drawer Support Head End Remove this Screw Only STEP A: Remove one Drawer Support screw from the Head End of the table as shown. STEP B: Insert Paper Shelf between the Top Rail and the loose Drawer Support. Make sure the Paper Shelf is mounted below the Tab as shown. STEP C: Reinstall the Drawer Support and its corresponding screw. Do not tighten at this time.
MODELS 2230 and 2240 STEP 5 Backrest Catch Screw G Snap Rivet Screw B Paper Shelf Nut H Snap Rivets STEP A: Install Backrest Catch as shown in the drawing above. CAUTION ! The Backrest Catch needs to be positioned on top of the Tab shown in STEP 4. STEP B: Install Screw B (1/4”-20 x 2”) through frame rail and into Backrest Catch and tighten Nut H (1/4”-20). Insert Screw G (1/4”-20 x 1/2”) through Backrest Catch and Tab. Tighten Nut H onto Screw G. STEP C: Install 3 Snap Rivets.
MODELS 2230 and 2240 STEP 6 Detail of Hinge Assembly Screw G Head End Nut H STEP A: Align holes in Hinge with holes in frame. Hinge must be oriented as shown with Hinge mounting flange facing the Head End of the table. STEP B: Install 4 Screws G (1/4”-20 x 1/2”) into the Hinge and through the frame. Fasten with 4 Nuts H (1/4”-20) and tighten.
MODELS 2230 and 2240 STEP 7 Detail of Drawer Slide Bumpers LH Side RH Side Drawer Support Screw E Drawer Slide Nut K Shelf Support STEP A: The Drawers can be installed so they open from the right hand side (RH Side) or the left hand side (LH Side) of the table. The view above and the instructions below are for a right hand installation. STEP B: Position the (4) Drawer Slides on top of the Drawer Support rails. The rubber bumpers should be on the LH Side of the table, facing upward.
MODELS 2230 and 2240 STEP 8 J-Bolt R Screw D J-Bolt R Screw D Bumper Backrest Support Bumper Nut L Cotter Pin Screw F Washer M Screw F Cotter Pin Clevis Pin Clevis Pin Foot End Clevis Clevis Tab Hinge STEP A: Lay upholstered backrest on Foot End of frame as shown. STEP B: Slide backrest down until it bumps up against Hinge. STEP C: Insert the four backrest-to-hinge Screws F (1/4”-20 x 1”) and tighten. STEP D: Insert Screws F (1/4”-20 x 1”) through Clevises and tighten.
MODELS 2230 and 2240 STEP 9 Rounded Corner Back Section Foot End Screw A Backrest Bracket Screw B STEP A: Rotate Back Section until Backrest Bracket is engaged or top is horizontal on frame. STEP B: Set upholstery bottom on frame, with Rounded Corners placed at the Foot End of the table. STEP C: Install Screw A (1/4”-20 x 4”) through frame and into upholstery. STEP D: Install 2 Screws B (1/4”-20 x 2”) through frame and into upholstery. STEP E: Tighten Screws.
MODELS 2230 and 2240 STEP 10 Snap Rivet Shelf Side Plate Screw B Lower Shelf Support Snap Rivet Snap Rivet STEP A: Loosen Screws B at the foot of the table where indicated just enough to allow installation of the Side Plate. STEP B: Mount Side Plate so that the slots of the plate straddle the Screws B that were just loosened. STEP C: Press the top of the Side Plate up against the frame and align the top hole of the plate with the hole in the frame. Insert Snap Rivet into the aligned holes.
INSTALLATION Leveling the Table (Figure A) A Leveling Screw Pad is located at each corner under the table’s base. Adjust the four Leveling Screw Pads, by turning them up or down, to achieve a solid, level installation. Installing the Paper Roll (Figure B) Slide the Dowel Rod through the paper roll and hang the Dowel Rod on the J-Bolts. Ensure a secure fit before using the paper roll dispenser.
DRAWER REMOVAL Retaining Clips Drawer (Bottom View) To remove Drawer from bottom slide support: Fully extend the Drawer, locate the Retaining Clips and push both clips in a clockwise direction as you pull the Drawer forward and out. OPERATION Back Section To Raise Back Section: Lift Back Section of upholstery to desired inclination and secure Backrest Bracket into one of the six Backrest Catch slots.
MAINTENANCE Preventative Maintenance • Inspect the mechanical functions to ensure satisfactory operation. • Check fasteners to make sure they are present and secured tightly. Cleaning Upholstery Regular care should be maintained by daily wiping with a damp cloth or sponge and periodic cleaning with a mild soap and water solution. Let air dry before placing anything on top of upholstery.