With Programmable Clock/Timer and Lighted Display Models: 1033519 20333 S. Normandie Ave. Torrance, CA 90502 Tel. (310) 787-5444 • (800) 421-6860 • Fax (310) 787-5412 U.S.A. E-Mail: brew@brewmaticusa.com Int’l E-Mail: brew_equip@brewmaticusa.com Website: brewmatic.com FM CS135 REV. F 8-22-07-Condensed Parts & Service B.I.C.A.
CONTENTS: Important Information Page 2 Appliance Information Page 3 Control Location & Description Page 3 Wiring Diagram Page 4 Trouble Shooting Guide Page 5 - 6 Parts Diagram & Parts List Page 7 - 8 Programming ( For Machines made starting from Serial No. 3432583 and Higher) Page 9 - 10 Programming ( For Machines made before Serial No.
APPLIANCE INFORMATION Appliance Specifications: Model Numbers: Descriptions: Dimensions: Volts: Watts: Amps: Hertz: Phase: Power Supply Cord: Plug: Power Supply Required: Wall Receptacle Required: Listing: Settings And Adjustments: 1033519 BICA With Programmable Clock/Timer and LIGHTED Display 13” W x 3-9/16” H x 9-3/16” D 120 1600 13.6 60 1 4 Ft. 3 Wire + Ground NEMA 5-15P. Furnished and attached 120Volts, 15 Amp, dedicated circuit. 15Amp. NEMA 5-15R.
WIRING DIAGRAM *For Fuse see page 7, Item 75 * Wire Diagram (Use for machines before serial no. 3432583) Wire Diagram ((Use for machines with serial no.
TROUBLESHOOTING SERVICE SHOULD BE PERFORMED BY QUALIFIED SERVICE PERSONNEL ONLY. WARNING: Turn off the "Power-Fill” toggle switch. Unplug the power supply cord and allow the coffee appliance to cool before servicing unless electrical testing is required. WARNING: Make sure installation instructions have been followed before attempting to test this coffee appliance. Note: Allow the coffee appliance to heat up to brewing temperature BEFORE testing the temperature, water volume or the hi-limit thermostat.
Symptom Possible Causes Remedies 10. Poor tasting coffee. Water deposits are plugging the spray head or siphon tubing. Water deposits are plugging the spray head or siphon tube. Clean the spray head and use the clean out spring. See the Maintenance And Cleaning section. The brewing temperature has not been adjusted correctly. The amount of coffee being used may not be correct. Change the amount of coffee being used. Use only one paper filter for each brew cycle.
PARTS DIAGRAM & PARTS LIST – Final Assy. Some Items have been removed for clarification Item No. 1 2 2a 3 Part No. Description Item No. Part No. Description 24 9903591 Clamp, Hose Double Tang 1031354 Weld Assy., Shell Elect. BICA (Use for machines with serial # 3432508 and higher) Weld Assy., Shell Elect. BICA (Use for machines before serial # 3432508) 26 9303104 Washer, Lock W/Int Tooth #8 1031355 32 1031357 Plate, Power Supply Assy.
PARTS DIAGRAM AND PARTS LIST Item No. Part No. 4 9907223 Description Gasket, S/S 13/32 ID x 11/16 OD 5 9202120 Nut, Hex 1/8-27 6 6000792 Fitting, 1/8 Str. Pipe x 5/16H 7 1030617 Spray Head 18 6000736 Tube, Silicone .5 OD x .297 ID x 2” Lg. 25 9903490 Clamp, Hose Miniature, 7/32 to 5/8 (Worm Drive) DETAIL -A Spray Head Item No. Part No. Item No. Part No. Description 23 9201145 Nut, Hex Std #8-32 S/S 26 9303104 Washer, Lock W/Int. Tooth #8 28 9001110 29 9203105 Screw, Mach.
PROGRAMMING YOUR BREWMATIC: (See Fig. 7) (ALL MACHINES STARTING FROM SERIAL NO. 3432583 AND HIGHER) SETTING THE CLOCK: Fig. 7 1. Press and Hold the “PROGRAM” button for approximately 3 seconds to enter Program Mode. The colon (:) on the display will begin to flash and a beep is emitted by the brewer to confirm that it is has entered Program Mode. 2. 3. To set hours, press and hold the plus (+) button; hours on display will advance from 00 to 12pm.
To Cancel the Programmed Brew Time 1. 2. 3. Press and Hold the “PROGRAM” button for approximately 3 seconds to enter Program Mode. The colon (:) on the display will begin to flash and a beep is emitted by the brewer to confirm that it is has entered Program Mode. Press the “PROGRAM” button one (1) time. Display will show the actual programmed brewing time To cancel the Programmed Brew Time, press the flashing “VOLUME SELECTION BUTTON”, the light will turn off.
PROGRAMMING: ALL MACHINES MADE BEFORE SERIAL NO. 3432583) PROGRAMMING YOUR ELECTRONIC BUILT IN COFFEE APPLIANCE: (See Fig. 2 for Control Location) SETTING THE CLOCK: 1. Press and hold the program button for 3 seconds; the display will first show the brew time, press once again and the display will show the clock time as indicated by the flashing colon (:). 2. To set hours press and hold the plus (+) button; hours on display will advance from 00 to 12pm.
ADJUSTMENTS CAUTION: Only those persons trained and qualified in equipment repair should attempt to open this coffee appliance. Make certain the appliance is not in brewing mode before making adjustment to the coffee appliance. Note: The brewing temperature of this appliance is preset at the factory. To adjust the temperature to a different setting, follow instructions below. ADJUSTING THE TEMPERATURE: (Fig. 3) (For Machines Made Before Serial Numbers 3432508) 1.
MAINTENANCE & CLEANING CAUTION: CAUTION: Note: Note: Only those persons trained and qualified in equipment repair should attempt to open and clean the inside of this coffee appliance. Turn the power switch off, unplug the power supply cord and allow the coffee appliance to cool before cleaning. Do not use abrasive or harsh cleaners as they may damage the finish of this coffee appliance. Failure to follow these cleaning instructions may damage this coffee appliance and may void the warranty.
20333 S. Normandie Ave., Torrance, CA 90502 (310) 787-5444 • (800) 421-6860 • Fax (310) 787-5412 USA E-mail: brew@brewmaticusa..com Int’l E-mail: brew_equip@brewmaticusa.com Website: brewmatic.