The Briarwood By Blaze King Model BRII/90 Insert Solid Fuel Heater Residential Approved LISTED BY: READ THIS MANUAL PRIOR TO INSTALLATION OR OPERATION OF THIS APPLIANCE. PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE.
To Our Valued Customers Dear Customer: Thank you for purchasing the BRIARWOOD II, wood burning insert (hereafter referred to as "stove"). This owner's manual explains the steps required to safely assemble, install, operate, and maintain your new stove. Be a responsible stove owner; PLEASE CAREFULLY READ THIS ENTIRE MANUAL BEFORE YOU INSTALL AND USE YOUR NEW STOVE. FAILURE TO FOLLOW THESE INSTRUCTIONS MAY RESULT IN PROPERTY DAMAGE, BODILY INJURY, OR EVEN DEATH.
Table Of Contents Description Page # General Information ................................................................................................................................... 4-8 Warranty ...........................................................................................................................................4 Approval Label ..................................................................................................................................5 Safety .............
General Information—Warranty BLAZE KING—Briarwood—LIMITED WOODSTOVE WARRANTY WARNING: TO VALIDATE THIS WARRANTY YOU MUST COMPLETE AND RETURN THE ENCLOSED WARRANTY CARD WITHIN 20 DAYS OF THE DATE OF PURCHASE. WHAT THE WARRANTY COVERS: Blaze King Industries and/or Valley Comfort Systems Inc. shall be referred to throughout this document as "Blaze King". This warranty contains different terms which cover different parts of the stove.
General Information—Approval Label BRIARWOOD II/90 INSERT WH- LISTED SOLID FUEL BURNING FIREPLACE INSERT MODEL: BRII/90 Tested to : UL 1482-1998 / ULC S628-M93 CERTIFIED IN BOTH UNITED STATES AND CANADA PREVENT HOUSE FIRES- Install and use only in accordance with Blaze King’s installation and operation instructions. Install and use in a code complying fireplace only. Stainless steel flue liner is required in Canada and recommended in the United States.
General Information—Safety BRIARWOOD Model BRII/90 - Fireplace Insert Residential Approved Briarwood Room Heaters have been developed, tested and constructed in accordance with the requirements of UL 1482-1998 / ULC S628-M93. Safety testing was performed by Intertek Testing Services laboratories. These units are designed as safe and efficient, solid fuel burning heaters, but they must be properly installed and operated.
General Information—Safety 13. Provide for adequate fresh air supply in the room while the stove is in operation. 14. Do not leave the house unattended for long periods of time when the stove is in operation. 15. Make sure pipe connections cannot accidentally come apart. Use sheet metal screws to secure pipe connections. 16. Clean your chimney and associated components regularly. Do not allow excessive build-up of ashes in the stove, or allow ashes to spill from the stove when the door is opened. 17.
General Information—Maintenance REMOVABLE BAFFLE PLATE The baffle is the part of the stove which receives the most heat. For this reason, as well as for chimney cleaning ease, it has been made to be easily removed. Remove the screws on each side of baffle and the bolt from the rear center of the stove, this will allow the baffle to slide forward and out. The baffle plate may be damaged by over firing and burning improper fuels. Baffle plate damage is not covered by warranty.
Installation—Location & Clearances YOUR STOVE'S LOCATION 1. Plan ahead to be certain that furniture will have ample clearance, and that drapes and curtains cannot come in contact with the room heater. Refer to the approval label on the stove for correct clearances to combustibles. 2. This stove must be connected to a chimney. It must be vented to the outside. Never permit your stove to ventilate itself into any room in the building. 3.
Installation—General BRIARWOOD II INSERT STOVE INSTALLATION PROCEDURE AFTER YOU READ AND FULLY UNDERSTAND THE MATERIAL IN THIS MANUAL, YOU ARE READY TO PROCEED WITH THE INSTALLATION OF YOUR STOVE. SAFETY NOTICE: IF THIS HEATER IS NOT PROPERLY INSTALLED, A HOUSE FIRE MAY RESULT. FOR YOUR SAFETY, FOLLOW THE INSTALLATION DIRECTIONS. CONTACT LOCAL BUILDING OR FIRE OFFICIALS ABOUT RESTRICTIONS AND INSTALLATION REQUIREMENTS IN YOUR AREA.
Installation—General INSTALLATION INTO FACTORY BUILT FIREPLACES In addition to the general instructions presented throughout the manual you must take care to ensure the following steps are correct when installing this insert into a factory built fireplace. 1) The factory built fireplace must be listed per UL127 or UL S620. 2) All clearances to combustibles must be maintained as shown on the label. 3) The installation must include a full-length liner, which is attached to the insert and to the chimney cap.
Installation—Chimney CHIMNEYS: GENERAL Refer to the chimney and chimney connector manufacturer’s instructions for additional information. If this stove and its chimney components are not properly installed, a house fire may result. For your safety, follow the installation directions. Contact local building or fire officials about restrictions and installation requirements in your area. We recommend that your chimney should be at least the same dimension (inside diameter) as the flue of your stove.
Operation—General ANDIRONS OR GRATES - (Not For Use On The Briarwood Insert) Briarwood Stoves are designed for the burning of wood directly on the firebrick. Best efficiency and burn characteristics are obtained when a half-inch bed of ashes is maintained in the firebox. STARTING YOUR FIRST FIRE (Curing Your Stove Paint) Make sure you provide extra ventilation by opening a door or window as the paint will give off fumes while it is curing. There will be some paint odor during your first few fires.
Assembly—General Assembly Instructions for Briarwood II/90 Insert There will be local building and fire codes which could affect this installation. Be sure you check with your local building inspector, fire inspector or other local authorities having jurisdiction in your area before you begin installation. This insert is certified only for installation into a masonry fireplace which has been carefully inspected and is in good condition.
Assembly—General / Optional OPTIONAL INSTALLATION INSTRUCTIONS Optional Gold Trim Installation: Assemble the trim strips as shown in (fig 12) and attach to the shroud outer edge using the screws provided. to step 4 and continue the installation. Return Optional Fans Installation: (Note: The following instructions pertain to both fans on the left and right sides of the stove.) 1. Determine which side of the stove the power cord for the fan should be located. 2.
Assembly—Diagrams OM-BRII/90I.PUB Page 16 Rev.
NOTES OM-BRII/90I.PUB Page 17 Rev.
