Sub-Frame Hitch Installation Instructions Mfg. No. 1695196 For Prestige / 1800 / 2800, Conquest / 1700 / 2700, & Broadmoor / 1600 / 2600 Series Tractors This kit is required when installing front mounted snowthrowers.
Installation Instructions Sub-Frame Hitch Main Hitch Components (All Applications) 28 29 27 30 29 25 41 33 39 38 40 37 36 35 42 1 3 2 28 27 51 43 33 25 33 25 33 29 28 28 25 25 27 27 25 50 30 28 27 4 28 22 31 5 32 22 46 27 34 26 6 25 45 49 7 24 48 8 23 9 15 9 9 47 17 16 10 13 18 21 Front Hole for Dozer Applications Rear Hole for Snowthrower Applications Hydraulic 20 Lift 14 11 13 11 9 Figure 1.
Installation Instructions Sub-Frame Hitch Ref 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 42 43 44 45 46 47 48 49 50 51 52 Part No. Qty.
Installation Instructions Sub-Frame Hitch NOTE: Please read through these instructions and the instructions of any other attachments before beginning installation. Assemble Push Bar Latch 1. Attach Push Bar Latch (B, Figure 3), to hitch. Secure with four .31-16 x 1 bolts (A), and four .38-16 flange nuts (C). WARNING Before beginning any service work turn off the PTO, set the parking brake, turn off the ignition, and disconnect the spark plug wire(s). B INITIAL ASSEMBLY C Assemble Hitch 1.
Installation Instructions Sub-Frame Hitch INITIAL INSTALLATION Snowthrower & Dozer Applications Manual Lift Models E LIFT LINK - EARLY VS. LATER The early model lift link (A, Figure 5) was used on early production Conquest/1700/2700 Series tractors. It must be replaced with the later model lift link (B) included with this attachment. The later model link works in all applications. Discard the early model link (A).
Installation Instructions Sub-Frame Hitch A B C D E Figure 8. Install Hitch A. J-Hooks B. Hitch Rod C. Hitch Rod D. Hook E. Clamp Plate Install Hitch 5. Push the clamp plate (D) backwards until it is snug against the lift shaft. Tighten the clamp plate hardware (E). 1. Slide the hitch under the tractor. 2. Raise the rear of the hitch and place the hook (C) over the lift shaft. 3.
Installation Instructions Sub-Frame Hitch D A B C A C B Figure 10. Install Lift Rod - All Models A. Lift Lever B. Lift Rod C. Clip Figure 9. Install Lift Lever A. Lift Lever B. Lift Shaft C. Safety Clip D. Clevis Pin Install Lift Rod 1. Slide the lift lever (A, Figure 9) onto the end of the tractor lift shaft (B) under the right side footrest. 2. Use the tabs on the lift lever (A) to capture the tractor lift arm. Secure in place with a clevis pin (D) and safety clip (C). 3.
Installation Instructions Sub-Frame Hitch Snowthrower Position C D A B E F A. Hitch Rod B. Hitch Rod C. Lift Lever Extension D. Lift Link (Manual) E. Pressure Lock Plate (Hydraulic) F. Hook Figure 11. Normal Installation & Removal REMOVAL NORMAL INSTALLATION NOTE: After removing components, reinstall the clevis pins and clips to prevent loss. 1. Insert the hook (F, Figure 11) into the back of the hitch. Mount the rear of the hitch on the lift crossshaft. 1.
Installation Instructions Sub-Frame Hitch Snowthrower & Dozer Applications Snowthrower & Dozer Applications E A A B F C D E C B D Mower Applications Mower Applications G A A B F G F E Figure 12. Lift Lock Plate - Hydraulic Lift Models A. Lift Cylinder B. Flat Head Pin (Original) C. Flat Head Pin (New) D. Lock Plate E. Hair Pin Clips F. Lift Shaft Assy. G. Washers C D Figure 13. Lift Link - Manual Lift Models A. Pin B. Rear Hole of Lift Bar (Snowthrower Applications) C. Spacer D.
Installation Instructions Sub-Frame Hitch NOTES MANUFACTURING, INC. 500 N Spring Street / PO Box 997 Port Washington, WI 53074-0997 USA Form No. 1733911-04 Rev. 01/2007 © 2007 Briggs & Stratton, Inc.