FORM NO.80324 November I. 1996 Read this document before operating the spreader . This manual is for Fisher Regular and High Capacity Hopper Spreaders with serial numbers (2600 - ).
PREFACE Welcome to the growing family of FISHER@ spreaderowners. substitute items as they could affect the perfonnance and warranty of this product. This manual provides safety, operation, maintenance, repair parts, and accessories information for your new FISHER spreader.To keep your spreader operating safely and efficiently, insist that all operators and maintenancepersonnel read and understand this manual.
T ABLE OF CONTENTS PREFACE Gear Case. 20 TABLE OF CONTENTS Gear Case Assembly. 2I SAFETY GENERAL Safety Battery Spreader Definitions. Precautions. Safety. INFORMA Labels. TION 1 ... I I I 2 4 TorqueChart Material Detennining Weights Vehicle Payload 4 . 4 5 OPERATION. Cab Control Engine Starting Stopping the Engine 21 Input Shaft Pre-assembly 21 Assembly of Pre-assembled Parts. ..21 Gear Case Disassembly. 22 Feed Gate -Regular 22 Capacity. Feed Gate -High Capacity.
SAFETY Safety .Stop the spreader before leaving the vehicle to unclog, adjust, oil, or clean the Definitions spreader .Before servicing the spreader, wait for all movement to stop. .Keep hands, feet, and clothing away from power-driven parts and the conveyor chain. .Do not climb on or allow others to climb on the spreader at any time while operating. C AUTION: Indicates a situation that, if not avoided, could result in damage to product or property. .
SAFETY Spreader Labels The diagram below indicates the location of the safety and identification labels. The numbers in the diagram correspond to the numbers listed below. 7~ 53~ 7 , 5 11 , /~ 3 9 0 FISHER@ Deca14-1/2 0 Serial X 15 (PN 20724) 8 Number Label (No p .N.) 0A Form No.80324 2 November 1.
SAFETY ~ Form No.
GENERAL Torque INFORMA TION Chart Regular Capacity When tightening fasteners, refer to Table I, See Figure 1 to determine the correct amount of Torque Chart, for the recommended fastener torque values. spreading material for the regular capacity hopper spreader . Table 1: Torque Chart Figure 1 High Capacity See Figure 2 to detennine the correct amount of spreading material for the high capacity hopper Material Weights spreader.
GENERAL Determining Vehicle INFORMA TION 4. With the occupants in truck for nonnal Payload hopper spreader operation, weigh vehicle to obtain gross vehicle weight (GVW). 5 Subtract the GVW from the GVWR to detennine the available payload to carry the material. 6. Obtain the weight per cubic yard (lb./cu. yd.) of the desired material from Table 2, page 4. Divide the weight into the payload to detemline the maximum volume of material that can be carried. Use Table 3 to record information. I.
GENERAL INFORMA TION Table 3: Determining Vehicle Payload Example: Coarse Salt -Dry Material Type Equipment installed when vehicle RC Mild Steel 8' was weighed Hopper Spreader Front Gross Axle Weight Rating (FGAWR) Rear Gross Axle Weight Rating (RGAWR) Gross Vehicle Weight Rating 8600 (GVWR) (lb.) Gross Vehicle Weight (GVW) (lb.) -6500 (empty) = Payload Available (lb.) 2100 Material Weight (lbJcu. yd.) + 1431 Maximum Volume (cu. yd.) = 1.47 Maximum Height (Approximate) ~ (in.
OPERA TION Cab Control 8 When the engine starts, release the ignition Identification switch. N OTE: If the engine does not start after 10 secondsof cranking, turn both vehicle and spreader ignition switches to OFF and see the Briggs & Stratton Owner's Manual that is shipped with the spreader. 9. After the engine starts, move the throttle switch to IDLE and hold for 1/2 -1 second to release the choke. 10. To control the engine speed: .Increase: hold the throttle switch at CHOKFlFAST . Figure 3 .
~ OPERA TION Clutch .Start Operation Baffle Adjustment the engine. Spread pattern and the amount of material dispensed depends on engine RPM, gate position, and baffle settings. 2. Adjust the speed to slightly above idle. 3. Move the clutch switch to ON. .Decreasing RPM and/or gate-opening will decrease the amount of material coming to the spinner. .Increasing RPM and/or gate-opening will increase the amount of material coming to the spinner. See Figure 4, and Figures 5 and 6 on the next 4.
OPERA TION These figures are as viewed from the top of the spinner looking down. Figure 5 Form No.
MAINTENANCE .Maintain spinner shaft-to-gear case roller chain tension. Correct chain tension allows 5/16" deflection midway between the sprockets. See Figure 7. To increase chain tension: loosen the bearing mounting hardware and pull the spinner shaft away from the gear case. Make sure the spinner shaft is vertical and the sprockets are lined up before re-tightening the fasteners. Oil this chain after each use, and at the end of the season.
MAINTENANCE Periodically check the conveyor chain tension. To check the tension, measure in 201'-24" from the rear edge of the sills. Push up on the chain with your hand. The conveyor chain should lift 1"-3" off the conveyor chain guide or cross angles. See Figure 9. Electric Clutch To minimize problems and extend the life of the electric clutch, do the following: .At the end of each snow season,remove and clean the clutch. .
PARTS DIAGRAMS Items with a single part number or description are 11 ~ AND LISTS ' .0 0..", "' 25 common to regular capacity mild steel and 16-gauge stainless steel 14- 24 " 14" and 26" chute assemblies. 23, .0 -8 0-/ 10 17, 18 (2 REa), 19, 20 ""', 2 6--4 ,3 ~ /~- 17, 18 (2 REO), 19, 20 , ,/ 6/ 5 , I 9 / 5 / / 12 / ~ /13 / / ITEM PARTNO. 1 1 1 9189 9031 9194 1 2 2 9032 .9298 .20092 2 .9299 2 3 4 .20093 ..9195 ..9201 5 ..91004 6 7 ..9261 ..
~ PARTS Chute Assembly -High DIAGRAMS AND LISTS Capacity 11 - , ~~~ 25 22 23, 24 " """' ," O /8 14 26 10 / r--. " " , 17, 18 (2 REa), 0 --? 20 -21 .~ ~ 18, ./ 19, -2 20 7 6 6- 19, b+--3 17, 18 (2 REQ), 19, 20 65 .9 /1 LJ / / 5 12 13 / / ,j/ ITEM PART NO. 1 2 9107 .20318 3 4 ..9195 ..9201 5 6 7 ..91004 ..9261 ..20599 ITEM QTY.
PARTS DIAGRAMS Conveyor Drive and Idler -Regular AND LISTS Capacity N 'm No.80324 14 OTE: Assemble chain link and pin to chain bar as shown. November 1.
PARTS DIAGRAMS Conveyor Drive and Idler -Regular AND LISTS Capacity Items with a single part number or description are common to regular capacity, mild steel and 16-gauge stainless steel spreaders. ITEM PARTNO. QTY. DESCRIPTION I I 4 5 6 10 11 12 13 14 16 17 18 20085 20094 9171 9169 9167 9172 9184 9164 9182 9183 9163 9174 9177 19 20 21 22 23 24 25 26 27 27 28 28 29 .9181 .9178 .9179 .
PARTS DIAGRAMS Conveyor Form No.
PARTS ITEM I 4 PART NO. 20327 9171 5 9169 6 20328 10 9172 II 20329 12 20330 13 20331 14 20332 16 20333 17 9174 18 20334 18 20335 1 1 1 ENGINE BASE HC MS GEAR CASE DRIVE SHAFr COUPLING 1 2 1 WIPER BELT HC STRAP, RUBBER HOLD illLER SHAFr HC ZYC 1 2 2 2 1 1 DRIVE SHAFr HC ZYC ROD END HC illLER SPROCKET 8T DRIVE SPROCKET 8T SPROCKET, #40 X 16TX 1.0" ill CONVEYOR CHAIN 8' HC 1 (16"-123 LINK) CONVEYOR CHAIN .20336 .9178 .9179 .
PARTS DIAGRAMS Form No.
PARTS DIAGRAMS Engine Drive with Clutch -Regular ITEM PART NO.
PARTS DIAGRAMS AND LISTS Gear Case Form No.
PARTS DIAGRAMS Gear Case ITEM PART NO. QTY. DESCRIPTION AND LISTS ITEM PART NO. 1 9171 1 GEAR CASE 17 .67258 AR 2 .67245 .67259 .67246 .67247 GEAR CASE HOUSING GEAR (BRONZE) WORM GEAR 18 3 4 1 1 1 19 .67260 I I SNAP RING WOODRUFF 5 6 7 .67265 .67266 .67249 1 1 INPUTS HAFf OUTPUT SHAFf 20 .67261 I (# 18 -HARDENED) WOODRUFF KEY 21 22 .67262 .67263 .67264 .7621 ("A" -HARDENED) 1/8 VENT PLUG .67248 .67250 .
PARTS DIAGRAMS Insert an output bearing cone and the bronze gear into the housing. Slide the output shaft through the bronze gear and bearing cone, taking care not to scratch the shaft. AND LISTS Items with a single part number or description are common to regular capacity, mild steel and 16-gauge stainless steel spreaders. N OTE: The end of the output shaft should extend 1.9411 beyond the machined mounting surface on the back side of the housing.
PARTS Feed Gate -High ITEM PART NO. DIAGRAMS AND LISTS Capacity QTY. DESCRIP'nON ITEM PART NO. QTY.
PARTS DIAGRAMS AND LISTS Cab Control Front View 2 0 D Electric Throttle 2/ ITEM PARTNO 1 2 3 4 5 6 7 * 20354 .9427 .9422 .67026 .20162 .9237 .67027 .65368 8 9 10 11 12 13 14 * * .20088 .20089 .20090 .20086 90681 9472 9415 3042 8329 Form No.80324 QTY. DESCRIPrION 1 1 1 I I 1 1 1 1 I I I AR AR AR AR I CAB CONfROL (ELEC.
PARTS Vehicle Part DIAGRAMS AND LISTS Harness Number: 20072 Brown -Electric , l GREEN RED BROWN BLACK ORANGE WHITE Orange -CHMSL , -Vehicle ~ Ground ~ Green -Electric Throttle Switch , ~ / Green -Electric Throttle Switch Spreader Part Number: Gray -Electric Switch ~Clutch Green GRAY Throttle Red -Electric Throttle Switch White -Starter Relay Ignition Switch ~ Black- Magneto \ Ignition Switch Green -Ground Ignition Switch Harness Black - 20073 White -Magneto RED BROWN ORAN
PARTS CI~,..tri,.. Electric Thrnttl~ Throttle Throttle DIAGRAMS AND 3--~ Pin~3 LISTS Crank (shown against the Electric Throttle Bracket ~ ~, according to step 4 of the ... installatIon 2 InstructIons below.) Engine Mount 9 ITEM PARTNO > ITEM QTY. DESCRIPTION I 2 20163 20134 I I ELECfRIC ELECfRIC THROT11.E THROT11.E BRACKET MOTOR 3 4 5 20129 67091 91027 I 3 3 ELECfRIC THROT11.E ARM #6-32X5/8 SBH CS STS #6-32 PT HX LK NUT NYIS STS Disconnect the battery cables.
A CCESSORI Center High-Mounted Stoplight ES (CHMSL) Kit 1 ITEM PARTNO. QTY. DESCRIP110N KIT ASSEMBL rrEM 10 I. 9486 9487 I I STOPLAMP STOPLIGHT 2 * * * ..9488 .9489 .9493 ..9490 I I I I GASKET STOPLIGHT GASKET VEmCLE HARNESS-STOPLIGHT PARTS BAG ASSY PROTEcrOR PLUG 5 6 * * * * * Y W/ PART NO. ..90693 ..90694 ..5793 ..8329 .3666 .6456 .13658 QTY.
ACCESSORIES Inverted Vee Assembly -Regular Capacity Mild Steel EndPlate 15,16,17 2 15, 16, 17 / '< G """ Cross Channel 1 ITEM 20 PART NO. 9138 1 .20164 2 .20165 3 .65994 Installation QTY .DESCRIPTION 1 1 1 1 INVERTED INVERTED INVERTED INVERTED ITEM VEE VEE VEE VEE KIT RC MS PLATE SUPPORT RC MS 15 16 17 PART NO. .90103 .90361 .90334 QTY. DESCRIPflON 10 10 10 3/8-16Xl HX CS 05 ZF 3/8 SF LK WASHER ZP 3/8-16HXNUTZP Indentedpartsare includedin the assemblyunderwhich they are listed.
ACCESSORIES Inverted Vee Assembly -Regular Capacity Stainless Steel Cross Channels / / 3,4, / 5 / I / / ~/ "'2 ~ ITEM PARTNO. QTY.DESCRIPTION I 20166 I INVER1ED VEE KIT RC MS 2 .65995 I INVER1ED VEE RC STS 3 .91015 4 3/8-16X1 HX CS STS 4 .91007 4 3/8 SPLK WASHER STS 5 .91008 4 3/8-16HX NUT STS Installation Indented parts are included in the assembly under which they are listed. Instructions 3, 1. Select the height for the inverted vee for the material being spread: .
ACCESSORIES ITEM PART NO. I 9347 I 9155 2 .20348 2 .20349 Installation QTY .DESCRIPTION I I I I INVERTED INVERTED INVERTED INVERTED ITEM VEE VEE VEE VEE KIT 8' HC MS KIT 10' HC MS 8' HC MS 10' HC MS PART NO. QTY .DESCRIPTION 4 .90103 12 3/8-16X1 5 6 7 .90361 .90334 .20165 12 12 2 3/8 SP LK WASHER ZP 3/8-16 HX NUf STS INVERTED VEE SUPPORT HX CS 05 ZP Instructions 1.
FISHER ENGINEERING 12 WATER STREET p .0. BOX 529 ROCKLAND,MAINE M Form No.80324 A DIVISION OF DOUGLAS Printed in the U.S.A. 04841 DYNAMICS, L.L.C. November 1.
